Search Documents

By E. D. Eastman

"The factors that determine the efficiency of reduction of iron oxides by gaseous reducing agents may be considered in two classes; those which effect the equilibrium between the reacting substances end their products, and those which affect the rete of reaction. Both sets are of prectical importance, the former as influencing the maximum possible efficiency and the latter as determining what fraction of the maximum yield may be readily or profitably obtained. In addition, the thermal changes attending the reduction greatly affect the chance of successful industrial application of any such process, and knowledge of them is necessary for the intelligent design of apparatus and control of the reaction. Some aspects of each of these three divisions of the problem are discussed below.I. The Maximum Reducing Power of Fuel Gases on the Oxides of IronsThe gases that heve been considered specifically in this work are coal gas, water gas and producer gas, typical analyses” of which are given in Table 1 Of the various hydrocarbons represented in Table 1, (several being grouped or averaged as C2R4), methane is the only gas assumed to be capable of existence at appreciable pressures under the conditions of interest here. The equilibria in the several systems which may ensue when one of the above gases is allowed to react with the iron oxides, may therefore be represented in the most general case by equations of the type of the following arbitrarily chosen ones:"

Jun 1, 1923

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

By F. W. Lee

The paramount importance of water to life of all forms on the earth is too well known to require elaboration in this brief paper. It has repeatedly been termed the most valuable of all our mineral resources. Its importance is justifiably recognized in the extensive areas covering the earth which receive sufficient rainfall to sustain a relatively luxuriant vegetation; but in those areas where rainfall is insufficient to support anything but a relatively meager plant growth, the location of a water supply and its development become of even more vital interest to those attempting to obtain a living from the soil. Geological investigations concerning the water supply of the United States have been most extensive, important work having been accomplished by Federal, State, and local governments and by private enterprise. A casual examination of the titles of the 739 Water-Supply Papers published by the United States Geological Survey3/ alone testifies 'to the vital nature of our water resources and the extensive work that has been done on them.

Jan 1, 1936

By Ralph H. Whaite

The Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region is described. A catalog of the maps that have been microfilmed in the Eastern Middle anthracite field--the first area to be covered in the program--is presented. Additional catalogs will be published as significant mining areas are completed.

Dec 1, 1964

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety, is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks, supplied-air respirators (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks),2 dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch, approval tests of other types of respira- tory protective equipment are conducted by the Health Branch, These branches are in the Health and Safety Division.

Mar 1, 1948

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950

By Liming Yuan

A computational fluid dynamics (CFD) study was conducted to model effects of coal properties on the potential for spontaneous heating in longwall gob (mined out) areas. A two longwall panel district using a bleeder ventilation system was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the three dimensional CFD modeling. The spontaneous heating is modeled as the low temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted for three different US coals and simulation results were compared with some available test results. The effects of coal surface area and heat of reaction on the spontaneous heating process were also examined.

Jan 1, 2008

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By F. E. Block, T. T. Campbell, D. Z. Hobbs

Several methods were investigated for the preparation of high- purity elemental boron in an attempt to develop a feasible process for producing boron on a large scale . In the work described in this report , the metal was prepared by metering boron trichloride gas into a crucible containing molten metal reductants . It was necessary to remove reaction byproducts by acid and aqueous leaching . Magnesium and sodium were tested as reductants , but best results were achieved using lithium or zinc as reductants . Contaminants originating from the materials of construction were the chief impurities in boron made by this method . Impurities ranged from 0.5 to 5.0 percent . Impure boron ( 85 to 90 percent ) was also prepared by the magnesium reduction of boron trioxide in a thermite - type reaction . This product contained magnesium as the chief contaminant . Impure boron made in this way could be upgraded by fusing with potassium fluoborate or potassium acid fluoride . After acid leaching the fusion cake , a product containing 95 to 97 percent boron was obtained . Analytical techniques for accurate determination of impurities in elemental boron are a major problem , requiring solution before a valid comparison can be made of the quality of boron prepared by these various methods .

Jan 1, 1964

By John B. Gayle

The suitability of fluid petroleum coke as a blending agent for producing metallurgical coke has been investigated using the Tuscaloosa and sole-heated experimental ovens. From the results of tests with three representative blends, it has been fond that additions of fluid petroleum coke effect the following changes: (1) Increase in size, resistance to shatter, and apparent specific gravity of cokes produced; (2) little or no change in coke hardness and stability or in the amount of breeze formed; (3) increased charge density; (4) modification of expansion characteristics of blends charged; and (5) decreased ash and increased sulfur contents of blends charged and cokes produced. Substitution of a calcined sample of fluid coke of greatly reduced sulfur content resulted in a coke of inferior physical properties. This effect indicates that additions of the calcined product should probably be limited and that other methods for producing a low sulfur fluid coke should be considered.

Jan 1, 1956

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By Lloyd Carpenter

Eighteen elements were determined spectrochemically in vanadium metal and its compounds in the general range of 1 to 1,000 ppm by means of spark-ignited unidirectional arc excitation. The samples were converted to vanadium pentoxide and combined with a mixture of graphite, lithium carbonate, and gallium oxide. For the molybdenum determination, the oxidized samples were mixed with sodium chloride and packed in copper electrodes. Average precision of the method was 15.6 percent relative standard deviation and relative error was 4.4 percent.

Jan 1, 1963

By M. E. Adam

This report describes the construction and testing of large (30 ft high by 55 ft wide) stopping and overcast structures in an oil shale mine. The work was undertaken to develop construction techniques and cost data, and to measure leakage rates on full scale structures in an oil shale mine. A design data base was developed by reviewing industry practice, oil shale industry plans, and technical literature. Alternate layouts for room and pillar mining were examined to find ways to reduce the size and number of ventilation control structures. Six full size stoppings and one overcast were built in the Colony Pilot Mine. Leakage rates were measured using both SF6 tracer gas techniques and the ?brattice window? method. The leakage was measured both before and after a full scale face blast. Blast air pressures were measured across two of the stoppings. Cost and leakage data were used to evaluate the projected overall performance of various combinations of the stoppings in a two-panel oil shale mine.

Jan 1, 1986

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By G. M. Potter

During the investigation of the occurrence of manganese deposits in the western United States, examining engineers of the Bureau of Mines collected samples from four properties in Siskiyou and Mendocino Counties northern California. As the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were made between 1941 and 1945 to determine the amenability of the ores to concentration. The Johnson and Reynolds properties are near Fort Jones Siskiyou County. The ore occurs in a number of small lenses in that area. Samples were taken for testing for amenability to treatment in a small custom-gravity plant, tentatively planned. by the Waiter Johnson interests of San Francisco. A 2-ton representative sample was obtained from numerous exposed portions of an outcrop on the property of the Mayland Mining Co. The Mayland mine is about 8 miles from Sawyers Bar in Siskiyou County. The ore body consists of stringers and irregular masses of oxide, and. silicate ore scattered through quartz, which these minerals have replaced.

Jan 1, 1952

By Hylton R. Brown

Although extensive research has been carried on to determine the factors affecting the explosibility of carbonaceous dusts, as much has been published on coal-dust and grain-dust explosions recent reports of loss of life and property in explosions if metal dusts emphasize the lack of information on the extent of the dust-explosion hazard in plants manufacturing or handling; aluminum, magnesium, or zinc powder, as well as other metal or mineral dusts. Early investigators believed that only the carbonaceous dusts formed explosive mixtures with air, and it was not until near the beginning of the present century that the explosibility of certain metal and mineral dusts was recognized generally. In his book, entitled "Fire and Explosion Risks," published in 1904, Von Schwartz called attention to such hazards. Many vague references to metallic-dust explosions are found in the literature, such as "a severe explosion of aluminum dust occurred in the Middle West several years ago," but very little information seems to be available on the extent of the hazard, the number of explosions, or the amount of loss caused by explosions in pants handling metallic or mineral dusts or powders other than those of a carbonaceous nature. A search of the records of insurance companies, rating bureaus, fire underwriters,and fire-protection associations as well as the files and records of Government agencies has been made to obtain authentic data on explosion losses. To indicate the extent of the hazard a summary of laboratory tests covering the explosibility of certain metal dusts, with brief reference to their uses and Methods of manufacture, and the data compiled from the information available on losses are presented in this publication.

Jan 1, 1941

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By Eugene Frey

"INTRODUCTION The Blue Bell fluorite deposits were examined in August and November 1944 by an engineer 3/ of the Bureau of Mines, and an underground project was set up. The Bureau of Mines began development of fluorite here February 10, 1945, and completed its survey on June 21, 1946.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepared the final report. The Metallurgical Branch, C. C. Ralston, chief, analyzes samples and perform beneficiaticn tests. The exploratory project was under the direction of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch. Acknow¬ledgment is due R. Thurston of the Federal Geological Survey for mapping the topography of the area, and to F. H. Gunnell and W. A. Young of the divisional office for detailed mapping of the surface and underground development and interpretation of the results.The chemical analyses included in this report was performed under the direction of H. E. Peterson, analytical chemist; the petrographic studies on the ore were written by LaMar Evans, petrographer; and the beneficiaticn section was written by C. H. Schack, metallurgist, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

Jul 1, 1947