Search Documents

By W. C. Phalan

"Prewar Conditions:Metallic magnesium may be considered a war metal, but a war metal with a future, so far as the industry in the United States is concerned. Its production in the United States prior to 1915, on a commercial scale, was negligible, but imports prior to that year may be taken as a gaze of the demand for the metal. Unfortunately, magnesium was not listed separately by the Department of Commerce prior to the war, among the importations, but was included with other metals, as follows: ""Barium, calcium, magnesium, sodium, and potassium, and alloys of which said metals are the component materials of chief value."" However, the imports of metals enumerated other than magnesium were probably small, so that the importations under the above caption may be considered chiefly metallic magnesium in one form or another and, therefore, is an approximate gage of the demand for the metal in the United States. These imports were as follows:These figures are so close that they give a good idea of the figures for the respective calendar years.Of this prewar use, it has been estimated that about 85 per cent was used annually and in approximately equal quantities in the production of (1) flash-light powder, (2) fire works, (3) aluminum casting work, and (4) nickel and nickel-copper alleys, such as monel metal, etc. The re¬maining 15 per cent was employed for general uses, such as deoxiding brass and other copper alloys in foundry work, and to a small extent in laboratory and research work."

May 1, 1920

By R. M. Santmyers

Of the sand and miscellaneous silica produced in the United States , ordinary sand and gravel are , of course , the most important, at least as regards volume of output . The building- construction industry absorbs approximately 75 per cent of the total value of all quartz and silica , as shown in Table 2 of Quartz and Silica, Part I, under "General summary . " Because of their unusual physical properties tripoli and diatomite find extremely wide uses in industry, and as the commercial deposits of these ninerals , especially tripoli , are scattered, large quantities enter into interstate commerce . Whereas ordinary sand and gravel are bulky commodities , these specialties have a fairly high unit value and hence can be transported relatively long distances .

Aug 1, 1931

By M. R. McKenzie

This paper describing the milling methods at the Walkermine concentrator, Plumas County, Calif., is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to James O. Elton, manager of the International Smelting Co., and to Henry A. Geisendorfer, manager of the Walker Mining Co., for permission to present this paper; to H. A. Geisendorfer and J. D. Roberts, shift boss, for historical facts, and to D. D. MacLellan, geologist, for geological information.

Jan 1, 1932

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

By Virgil J. Stachura

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine that resulted in smoother highwalls. The 17; were smoother due to reduced overbreak and inherently safer A, to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delays, which changed the effective delay pattern geometry and the direction of burden movement. The blast delays in the highwall holes were 50 to 100 ms longer than the mine's nominal design pattern (flat V, 17- by 42-ms surface delays, 200-ms in-the-hole delay). The burden movement was effectively changed from a 45* angle to 90* with respect to the highwall. The results of the blast delay changes were evaluated using terrestrial photogrammetry to generate vertical profiles at regular intervals. This evaluation showed that delay changes produced generally smoother vertical profiles.

Jan 1, 1984

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By W. W. Adams

"The results of the fourth annual safety contest, 'mown as the National Safety Competition, contacted by the United States Bureau of Mines are herein announced. A bronze trophy, ‘Sentinels of Safety’, the gift of the Explosives Engineer magazine, has been awarded to the leading mine in each of the five groups into which the mines and quarries that participated in the contest were arranged. These five groups were: anthracite mines, bituminous coal mines, metal mines, nonmetallic-mineral mines, and carries and open-pit mines. The leading plant in each group was the mine whose employee lost the smallest number of days from accidents in proportion to the total number of man hours worked. Where two or more mines operated without a lost-time accident, the winner was adjudged to be the plant which operated the largest number of man hours during the year.The contest was based upon reports of accidents and exposure sent by the competing companies to the Bureau of Mines. Records of the five leading companies in each group were made known to a Committee of Award, consisting of the following seven members: H. Poster Bain, Secretary of the American Institute of Mining and Metallurgical Engineers; James F. Callbreath, Secretary of the American Mining Congress; W. H. Cameron, Managing Director of the National Safety Council; H. L. Gandy, Secretary of the National Coal Association; A. T. Goldbeck, Director of the Engineering Bureau of the National Crushed Stone Association; William Green, President of the American Federation of Labor; and A. J. R. Curtis, Assistant to the General Manager of the Portland Cement Association. Members of the committee voted for the winning company in each group in accordance with the rules governing the contest.. A majority vote prevailed."

May 1, 1929

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By A. B. Needham

A number of the pegmatites in the southern Black Hills of western South Dakota contain sheet mica; and as the demand increased during World War II the area became an important producer of strategic qualities of mica. During this period of maximum activity, the U. S.. Geological Survey made detailed studies of the geological structural control, the mineralogical associations, and the production Of many pegmatites in the Black Hills. On the basis of results of this study, and at the suggestion of the Geological Survey, several of the pegmatites were examined by the Bureau of Mines, and a few were selected for further investigation. Accordingly, the White Bear, Silver Dollar, Buster Dike, and Hot Shot mines were diamond-core-drilled in 1947. The Hot Shot mine was investigated further by deepening the shaft and crosscutting the pegmatite in 1948. The mica-bearing deposits occur in lenticular intrusions of pegmatite in schists of various mineral composition. Eleven diamond-drill holes, totaling 2,111.4 feet in length, were completed on the four deposits. The shaft on the Hot Shot deposit was deepened 44 feet to the 112-foot level, and crosscuts were driven from the bottom of the shaft to the hanging Wall and foot wall of the pegmatite. This publication briefly describes the location, ownership, and history of the deposits and gives details of the work done by the Bureau of Mines and the Geological Survey.

Jan 1, 1950

By F. E. Brantley

Blister copper was successfully deoxidized with any of a variety of reducing gases; lancing techniques or a vertical-column furnace were used to contact the copper and gases. Of the gases tested, butane, when used to lance molten copper at about 1,200° C, reaction temperature, was slightly more effective than propane, natural gas, carbon monoxide, or reformed gas for deoxidizing copper from about 1.0 to less than 0.1 percent oxygen content, Laboratory-scale tests revealed that the vertical furnace, composed of a heated column packed with silicon carbide chips or hollow carbon cylinders, was significantly faster and more efficient than the lancing technique for deoxidizing molten copper with any of the gases tested. Comparison of the gaseous-reduction method with the conventional poling method suggests that the gaseous method has important technical and economic advantages for deoxidizing blister copper to any readily controlled amount of residual oxygen content.

Jan 1, 1962

By Donald W. Ross

Petroleum oils of widely different grades have long been clarified or decolorized by contact with fuller's earths. More recently, so-called activated clays have also been used for this purpose. Still more recently ouch clays have been used in the form of nodules termed "catalytic pellets." Clays of varied appearance and from different localities possess the desired bleaching qualities, but evaluation of such clays, so useful to the oil industry, has not been simple. Previous methods of identification and evaluation have largely followed procedures of production methods and were not primarily based upon the fundamental properties of the clays. Thus) a false assumption has grown up that) bleaching clays probably have no common properties on which a-method of comparison can be based. Fuller's earths and activated clays have a large absorptive capacity for the color constituents of petroleum and its products decolorizing is accomplished by bringing the oil into intimate contact with the clay and later separating the decolorized oil from the clay with its load of absorbed coloring matter. Former practice in absorbing "color" was to use the clay as granules or In' powdered form. More recent practice is to use clay pellets that are more abrasion-resistant than the granules. The oil is either filtered through a bed of clay, percolation method, or agitated on contact with the clay, contact method. Viscous oils are decolorized at an elevated temperature, so that their viscosity is lowered to the point at which thorough contact with the clay is insured. Nonhumidifying, nonoxidizing gas, such as dry steam or dry nitrogen, is used to seal such hot oil masses from the atmosphere.

Jan 1, 1948

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking focused the attention of the Bureau of Mines on the need for safety standards For such operations. Information Circular 7810 was published to meet that need. The current revision updates and replaces IC 7810. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1968

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By John Nagy

The Bureau of Mines adapted thermal theories explaining combustion of gases to correlate parameters affecting ignition of dust dispersions. The dust dispersions were ignited in a Godbert-Greenwald furnace at atmospheric pressure. Ignition temperature and the concentrations of fuel, admixed inert powder, and atmospheric oxygen were related mathematically. Values for these parameters obtained in laboratory experiments for cornstarch agreed with theory. The developed equation permits extrapolation; the predicted upper igni-tion limits correspond with limited experimental data from laboratory and large-scale tests. Explanation of the effect of fineness of dust on ignition parameters is attempted by introducing a surface-area constant to modify the activation energy. Arguments are presented to show that the ignition process is a solid-gas phase reaction rather than an ignition of prevolatilized gases.

Jan 1, 1966

By K. J. Liles

The U.S. Bureau of Mines evaluated the physical properties of ceramic particulate composites made from titanium nitride (TiN), alumina (AI203), and aluminum nitride (AlN) as part of a program to meet the high-performance demands on structural materials for new and emerging technologies. Samples containing from 20 to 80 wt pct TiN were pressed and fired, and their composition, Vickers hardness, modulus of rupture (MOR), and fracture toughness were determined. X-ray diffraction and scanning electron microscope (SEM) analyses showed that, depending on the amount of TiN added, the microstructure of the samples consisted of either a titanium-aluminum-oxynitride (TiAlON) particulate in a spinel matrix or a spinel particulate in a TiAlON matrix. The best results of the physical tests were achieved on a mixture of 40 wt pct TiN, 30 wt pct A1203, and 30 wt pct AIN. Sintering aids were added in 1-and 3-mol-pct increments to the 40-30-30 mixture to determine their effect on microstructure and physical properties. Results of an analysis of variancf' on a 4 by 4 factorial analysis showed significant effects on density, MOR, and Vickers hardness.

Jan 1, 1989

By Berger

A detailed description is given of radio apparatus for controlling a coincidence outfit for relative gravity measurements. This is probably of little interest, since many types of apparatus could be used. The general method employed is the interesting thing about this paper. As long ago as 1883 von Sterneck made a proposal to control two coincidence boxes with the, seine, clock, and many persons have suggested the use of radio for this purpose. In accomplishing this it would appear to the reviewer that this method is probably inferior to that used by the Marland Oil Co., but Berger and Brückner must be given the credit for important advances in the coincidence method. In their apparatus a clock at a central station actuates a relay, which operates a short-wave transmitter (40 m.). At the receiving station the amplification is accomplished at low frequencies... The signal operates a relay which moves a slitted screen in a coincidence apparatus. This screen has been improved considerably, to decrease the mean error in observing a coincidence. As usual, a telescope is used to observe the flashes of light. It has a scale in its focal plane and positions of successive flashes are easily read off and recorded by a second observer. This makes possible' a: higher accuracy in determining the exact instant at which coincidence would have occurred at the zero point on this scale. This method obviously depends on the constance of the mechanical and electrical lag inn both sending and receiving apparatus, and may be adversely criticized from this standpoint. -- A. E. Ruark.

Jan 1, 1929

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By Sidney Katell

This study presents the economics of the hot-carbonate purification process for removing C02. It considers three variations of the process in order to meet the design specifications, which call for a feed-gas flow of 10 million standard cubic feet per hour (std.c.f.h.) with C02 inlet concentrations of 10, 20, and 30 percent and exit C02 values of 5, 2, 1, 0.5, and 0.1 percent. Inlet pressure and temperature are 350 pounds per square inch [e] (p.s.i.g.) and 300° F., respectively. Estimated capital and operating costs are shown in the following to tabulations: [ ]

Jan 1, 1960