Search Documents

By Robert R. Perron

The U. S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 15 to 30 ampere fault to ground, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1975

By J. W. Davis

The storage stability characteristics of a diesel type fuel were determined to evaluate the effect of the polar compounds in the fuel. These compounds, comprising most of the nitrogen and oxygen containing compounds and many sulfur containing compounds, were separated from the fuel with a chromatographic column. This fraction was further separated into three polar extracts by graded elution through the column. Each extract was characterized. A storage program using the depolarized fuel, the fuel as received, and blends of the extracts with both fuels, was conducted. Results showed that the removal of the more polar components stabilized the fuel. Blending the polar extracts with the original fuel and with the depolarized fuel in the same ratio as they existed originally and at two and three times the original ratio increased the amount of gum present before storage, but had little effect on the formation of additional gum during storage. Distillate fuels produced by commercial refining of petroleum contain traces of organic nitrogen, sulfur, and oxygen compounds that are more polar4 than the remainder of the fuel. Recent laboratory studies by the Federal Bureau of Mines (1),6 in which these compounds were removed from a fuel, have shown that they influence its storage stability. The objective of this work was to determine the amount of these compounds present in a fuel and their effect upon its stability in storage. To evaluate the role of these polar compounds, it is necessary to remove them from the distillate fuel. Many can be removed by chemical treatment (2), but such treatment precludes reblending the polar components to approximate the original fuel composition. Solvent extraction is free of some of the criticism of chemical treatment, but it is more difficult because of the complex mixture from which compounds must be removed.

Jan 1, 1961

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By Floyd R. Anderson

Noise control of existing pneumatic drills is difficult and runs into cost, performance and weight penalties. A need exists for a start-from-scratch approach for quiet pneumatic rock drills. The designs based on Leavell Principles which has been successfully used in demonstrating a quiet and vibration free paving breaker, is the concept chosen here. This report shows the feasibility of a quiet stoper for drilling roof bolt holes in coal mines. The work is directly applicable to pneumatic percussive rock drills. The report shows an oscillator based on patented Leavell concepts which results in a vibration free tool and noiseless exhaust. Dynamics of the oscilator is analyzed. Independant rotation of drill rod is provided by an air motor (screw expander) and flushing of cuttings is accomplished by an air ejector in a compact lower housing. The feasibility of no exhaust noise, low drill machine noise, and vibration free casing is discussed.

Jan 1, 1977

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By S. M. Runke

[The coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, end metallurgists. These studies have amassed a rather astounding array of published and unpublished information. Correlation of geological studies between individual pegmatites, as well as between major districts, has brought fort come semblance of order to the knowledge of the structure and mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain pegmatites and pegmatitic zones into several grouts of associated minerals, based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or trouping of minerals, with the methods that have been developed for recovering certain of these minerals, possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by u single integrated process.]

Jan 1, 1952

By C. H. Fisher, Abner Eisner

"INTRODUCTION Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils 4 such as gasoline, kerosene, and neutral oils from coal—tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 60 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin—free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin—free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water—soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiatingbetween cyclic (naphthenes) and acyclic hydrocarbons (paraffins). Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons,It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings."

Dec 1, 1937

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By R. A. Guereca

Preliminary to an experimental study of selected physical properties of helium and related gases) the Bureau of Mines Helium Research Center conducted a data-gathering literature survey. This report combines the results of the 1961-63 literature search into a usable format. The data accumulated on the physical properties are presented in tables and graphs. The data in the tables were chosen for exact representation and comparison of specific values. An attempt was made to select the most reliable and consistent value available for a given property without extensively analyzing each source reference. The methods of evaluation are discussed later. The graphs show trends and anomalies which may be obscure in tabular form. (Reprints of the graphs) with the scale grid enlarged 2 1/2 times) are available upon request through the Research Director) Helium Research Center.) The literature search was conducted using Chemical Abstracts as the primary reference source with additional information drawn from Applied Science and Technology Index) Chemical Reviews) Physics Review) Science Abstracts (Physics») and other abstracting services. Part of the data included in this report have been tabulated previously by others (£-1).5 In a few areas) the sources of information are scarce and obscure (for example) refractive index and dielectric constant). The search was extensive; however) some sources

Jan 1, 1967

By R. V. Higgins

The results of two separate but related studies are given. In the first study, four equations were tested; the object was to determine which would produce a curve that would best fit data points that represent a trend of declining oil production in 90 California fields. Two conventional equations (the Arps and semilog) and two novel equations (extreme-c and double semilog) were tested. The curves were first fitted to the initial 9 years of the 15-year production data and then extrapolated for 6 years to determine how well the extrapolated curve would fit the data points. The generated curves were also extrapolated beyond the last data point to predict rates of future production. The results of the first study showed that no equation was clearly superior to the others in all respects. The semilog equation resulted in the best fit to production data for the first 9 years, but the Arps and extreme-c equations produced a better fit for the extrapolated data for the period of 9 to 15 years. The Arps and extreme-c also gave more realistic production rates when extended to the point where cumulative production equaled reserves. A second study was made to determine if the least-squares technique applied to the Arps equation would result in more accurate extrapolations. The merits of the logarithmic and the nonlogarithmic forms of the Arps hyperbolic equation were also tested. For the logarithmic expression, it was found that one of the constants of the Arps equation reached a value so small or so large that the equation was not applicable to the data of 40 of the 90 California fields. The nonlogarithmic form of the Arps equation was applicable to neither the same 40 fields nor to a few additional ones. When the data and the Arps equation were compatible, the use of the least-squares technique as compared with other methods improved the extrapolation accuracy somewhat.

Jan 1, 1971

By P. S. Jacobsen

In 1960 over 93 percent of the coal cleaned mechanically in the United States was cleaned in processes that utilized water or dense-medium suspensions of fine solids in water. Thus, in the process of removing deleterious ash-forming and sulfur-bearing minerals, another deleterious substance--water-- is added to the coal. The subsequent removal of the water from the coal, and the concomitant recovery of the coal from the water, is not troublesome in the sizes coarser than 1/4-inch. In the finer sizes, however, it is a difficult procedure that often costs more than the original washing operation. Because of the importance of liquid-solids separation in coal preparation, the Bureau of Mines has a continuing program of research in this field. The objective is to make available information on the performance characteristics of various types of equipment available for liquid-solids separations, thus promoting the wise selection of equipment for specific applications, and, thereby, more effective processing of coal. Results of work on flocculation as an aid to filtration5 and the sieve bend screen6 have been published. The present investigation of the screw-type classifier operating in combination with the cyclone was undertaken primarily because such classifiers are comparatively new to coal preparation and information on their performance is not available. The cyclone has become well-known since its introduction in this country by the Bureau of Mines in 1948.7 Use of the cyclone in conjunction with the screw-type classifier represents an attempt to provide the maximum recovery of solids at minimum moisture content.

Jan 1, 1962

By W. S. Wright, A. W. Tolonen

"INTRODUCTION The Mount Andrew iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by an engineer 4/ of the Bureau of Mines accompanied by geologists 5/ of the Federal Geological Survey. From October 20 to 27, 1942, two engineers 6/ of the Bureau of Mines made a further preliminary examination and took three large samples of magnetite and magnetite-copper ore for metallurgical testing. During the stunner of 1942 an investigation of the Mount Andrew-Stevenson-Mamie area, including topographic and geologic mapping and a magnetic survey, was made by geologist 7/ the Federal Geologically Survey. On May 31 and June 2, 1943, two Bureau of Mines engineers 8/ conducted a preliminary examination in which special attention was directed to trails, camp, and drill sites. They were accompanied on May 31 by L. A. Warner of the Geological Survey.During the period from September 1943 through September 1944 Bureau of Mines engineers 9/ completed a thorough investigation which included trenching, core drilling, and sampling. A Federal Geological Survey representative 10/ examined all trenches and cores for geological data.LOCATION AND ACCESSIBILITYThe deposit is situated at latitude 55º 31' N. and longitude 132º 18' W. on the north side of Kasaan Bay on Prince of Wales Island, Southeastern Alaska. The general location is shown on figures 1 and 2. The deposit is 5 miles southwest of the village of Kasaan and by water, 27 miles northwest of Ketchikan; the main tunnel portal is 7/8 mile north of the Mount Andrew landing on Kassan Bay."

Nov 1, 1947

By Parry. V. F., W. S. Landers

"INTRODUCTION Approximately 1,250,000 tons of 2-1/2-inch and 1-1/2-inch slack, representing over half of the output from 40 to 50 mines, is produced in the Denver region each year. Part of this slack is made by crushing lump, and some of it is rescreened to make pea and modified pea sizes measuring 1-1/2 inches by 2-1/2 inches and 3/4-inch by 1-1/2 inches, round-hole. Modified pea is popular as domestic stoker fuel. Approximately 900,000 tons of slack 0 by 2-1/2 inches, 0 by 1-1/ 2 inches, and 0 by 3/4-inch in size are consumed by industrial plants, the principal consumers being a large power plant and the beet-sugar industry. The power plant uses annually 250,000 to 275,000 tons of pulverized fuel and can pulverize slack of any size, while the sugar factories consume about the same quantity of coal in stokers. The sugar factories store about 110,000 tons of 2-1/2-inch slack under water from January to October, and burn the remainder of their consumption directly during the campaign season from October to December. For this purpose, sugar-factory power plants can use any size of slack, which is recrushed to pass a 3/4- or 1/2-inch screen before burning on chain-grate stokers. About one-third of the 2-1/ 2- inch slack produced in the field is used in smaller industrial plants that employ stokers.Certain factors affect the utilization of 2-1/2-inch slack in the Denver region. The increasing production of hydroelectric power has reduced the consumption of coal at power plants slightly. If more hydropower is generated, the trend of consumption of slack might be downward, unless industrial activity offsets this greater output. Rapid increase in number of domestic stokers during recent years has necessitated preparation of greater quantities of stoker coal, with the result that more lump is crushed, and preparation facilities are changed. At present about 19 percent of the coal produced is crushed to meet the constant demand for industrial fuel as well as the increasing but variable demand for the small domestic stoker sizes. The quantity crushed has increased 12 percent during the last 6 years. These factors are shifting constantly. The trend toward the use of clean and smaller sizes for domestic stokers gives a slack having a larger proportion of fines. In future, even greater quantities of small stoker coal probably will be prepared, and the resulting greater quantities of small slack will have to be used for industrial purposes."

Aug 1, 1942

By Jr. Gabler

World resources of cobalt appear ample for the foreseeable future; however, political and economic events have caused concern over the availability and reliability of an uninterrupted supply. Because of this concern, the U.S. Congress requested that the U.S. Bureau of Mines initiate a study of the flow of cobalt in the economy that would delineate and quantify the production areas where metal values are lost. As a result, the Bureau has developed a computerized commodity flow model. A major attribute of this model is that it is amenable to updating as supply, demand, and/or production data change. This report follows the flow of cobalt through its metallurgical and chemical applications and highlights areas where significant losses occur due to downgrading, export, or disposal. The study indicates that about 4,300,000 lb of cobalt-bearing materials are lost each year, representing 24 pct of U.S. domestic demand.

Jan 1, 1990

By G. R. Peterson

To determine the availability of aluminum from world bauxite resources, the Bureau of Mines investigated 139 bauxite deposits worldwide and evaluated the potential production of aluminum based on the demonstrated resources of bauxite ore from 91 mines and deposits in 22 market economy countries. The demonstrated resources of the bauxite mines and deposits included in this study represent an in situ resource of 20.2 billion metric tons of bauxite. Total identified bauxite resources in market economy countries amount to roughly 31.9 billion tons. Of the demonstrated resource, some 18.8 billion tons of bauxite considered minable provide a production potential of 3.6 billion tons of primary aluminum. Given the wide geographic distribution of bauxite deposits, stable supplies of bauxite for aluminum production seem assured well into the next century. However, a tight market situation could develop during the 1990's unless the real price of aluminum increases enough to stimulate massive new investments in production capacity, particularly in refining and smelting. This study indicates that a real price of at least $0.85 per pound (in January 1980 dollars) would be necessary to stimulate the required investments and provide a sufficient rate of return on invested capital.

Jan 1, 1983

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This article focuses on U.S. Bureau of Mines (USBM) and National Institute for Occupational Safety and Health (NIOSH) research to examine factors that had a significant influence on mine face ventilation design during the past century. Several "milestone" events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative face ventilation designs and a consistent commitment to mining health and safety. Ventilation has always been a concern in underground coal mining. For many yeas, there was no appreciation of how ventilation could be used to remove harmful contaminants from the air or how to control airflow quantities. The first known problems with ventilation date back to the 14th century, when it was recognized that lack of air was a major impediment to the expansion of mines. The common method of solving ventilation problems at that time was to abandon the existing mine and start a new one nearby. Ventilation in the early days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings. Later, in the 18th and 19th centuries, a furnace was introduced underground to increase the updraft in the return shaft. This allowed for a larger quantity of air in circulation. When mines went deeper and became larger, mechanical ventilation became necessary and was first accomplished by steam-driven fans. These fans became more prevalent as furnaces were prohibited in underground mines, especially after the Avondale disaster in Pennsylvania in 1869 (Roy, 1876). Eventually, these fans were replaced by more powerful, electrically [ ]

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989

By Benjamin C. Pollard

The location and production potential of a large block of strippable reserves in North Dakota were determined by using published data as a base and adding new drill hole data or other data contributed by companies that presently own or lease coal lands. Only beds exceeding 5 feet in thickness, under less than 120 feet of overburden, and in large blocks of 5 million tons or more were included in the estimates. All such reserves are in the Fort Union Formation of western North Dakota and are lignite in rank. Sixteen large blocks of reserves evaluated in this study are estimated to contain a total of 4.1 billion tons of strippable lignite.

Jan 1, 1972

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966