Search Documents

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By Donald O. Capstick

A mineral survey of the approximately 144,000-acre Borah Peak study area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Forest Service. The area studied included the Borah Peak RARE II roadless areas (No. 14210, 119,864 acres of land recommended for wilderness designation; and No. X4210, 18,440 acres of land recommended as non-wilderness) and other contiguous Forest Service administered land. The study area is in Challis National Forest in southeast Idaho about 30 miles south-southeast of Challis, ID. Burnt Creek, a conterminous study area to the northeast, on lands administered by the U.S. Bureau of Land Managment, was examined concurrently. Dolomite and limestone inferred reserve bases exceed 1 billion tons each within the Borah Peak study area. The material is widespread and of high quality. Extensive sampling and more detailed mapping are required to better define the resources; however, ample dolomite and limestone occur nearby, outside the study area. Dolomite is the main constituent of several geologic formations within the study area. Sample analyses indicate that the more than 1,000-ft-thick Jefferson Formation dolomite is the most pure and is equivalent to material being mined at a dolomite-to-magnesium processing plant near Addy, WA. Analyses from limestone-bearing formations underlying much of the study area indicate that large quantities of the limestone may be suitable for a variety of uses.

Jan 1, 1987

Provide long-term measurement of mine sidewall closure in backfilled stapes subject to flooding. Approach A water resistant extensometer is made by enclosing a rod-actuated transducer in a telescoping tube which is enclosed within an oil-filled outer housing. How It Works To assemble a water resistant extensometer, a cylinder -shaped transducer and two support rings are pushed into the small-diameter section of the telescoping tube where the transducer is held in place by friction. The outside of the small-diameter section of the telescoping tube is then greased and slid into the slightly larger-diameter section. See drawing. The cylinder-shaped transducer contains a potentiometer whose actuating arm is attached to a stainless steel extension rod that passes through one end of the telescoping tube. A similar rod is attached to the opposite end of the transducer body, and extends through the other end of the telescoping tube. A coil spring inside the large diameter end of the telescoping tube extends the tube

Jan 1, 1978

By F. S. Crawford

"After many years of safety activity in the United States in one form or another it becomes increasingly evident to those in contact with safety work that to achieve continuous good results in accident prevention there must be an aggressive organization behind the safety movement at each mine with fairly definite plan and policy. A study of the methods used by various companies and the results they have attained will be of value to the common cause of safety promotion.A study has been made of the safety records of the Menominee iron range in the Lake Superior district, and of data from the county mine inspector's report. Several companies on this iron range that have attained a certain measure of success in their work of accident prevention have given data, and a summary of their safety methods is presented.The Menominee iron range of Michigan lies in the southern portion of the upper peninsula of Michigan, bordering on Wisconsin. It consists of two main. divisions--the West Menominee Range, situated in Iron County in the vicinity of Iron River and Crystal Palls, and the East Menominee range situated in Dickinson County in the neighborhood or iron Mountain, Mich. The mines about Iron River and Crystal Falls are peculiarly subject to fires in a carbonaceous, sulphur-bearing black slate which appears in the footwall. This gives considerable trouble because fires in this material start from spontaneous heating. The methods of mining are top slicing and open stoping, working on benches along the sides of the stopes. The character of the ground varies from medium Soft ore to relatively hard ore which permits open stoping. Approximately one-third of the operating mines are equipped with a fan for main mechanical ventilation. The remainder are ventilated by natural draft. The East Menominee range is the older, top slicing having been used there for a number of years, and the timber mats have boon well developed. In common with all districts, some companies pay more attention to safety than others, although, those which do riot have the best records do pay some attention to safety.During the past three years the annual production per man employed has remained about constant, but in many mines a general decrease is shown in the accident record. The variation in the results attained can be ascribed mainly to the earnestness with which accident-prevention work is pursued, essentially regardless of the method of mining used. This is shown to be generally true, because the record indicates a steady decrease in one mine with an active safety department, while in adjoining mines with the same kind of ground and method of mining but where not such intensive attention has been paid to safety work, the accident record is high."

Oct 1, 1931

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By W. H. Somerton

The basic objective of this project was to determine the permeability of coal fracture systems as a function of effective stress. The detailed steps in accomplishing this objective are given in Article I of the contract under which the work was conducted as follows: Sec. 1.1 The objective shall be to determine the permeability of the coal fracture system as a function of effective stress. At least three bituminous coals shall be studied and at least five samples of each coal shall be tested. The sample size shall be as large as possible to be representative of coal found in the seam; a minimum of four inches is preferred.

Jan 1, 1974

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

By P. L. Woolf

Blast furnace coal injection tests conducted by the Bureau of Mines in cooperation with a consortium of 22 steel companies in 1963-1964 are described. These tests were part of a program of extensive investigation of auxiliary fuel injection in the Bureau's experimental blast furnace located at Bruceton, PA. Seventeen coal tests are described on various coals ranging from anthracite to subbituminous. Factors affecting maximum rates of injection were studied. These included coal size, coal type, and oxygen enrichment. The effect of high sulfur content coal and the means to control metal sulfur were investigated. An epilogue briefly describing the commercial experience with coal injection from 1960 to the present has been included.

Jan 1, 1985

By R. W. Stahl, H. E. Sanford, J. B. Benson

Immediately following the capitulation of Germany in World War II, the German State was occupied by various allied forces, who supervised all indus- trial activities in the area. Coal production is vital to the industrial life of Germany, and most of the coal is mined in the American- and British- occupied zones of western Germany. The British-occupied zones include the Aachen and Ruhr districts, from which approximately 90 percent of the coal is obtained. Figure 1 is a map of the Ruhr district. Because of the magni- tude of the task of insuring an adequate supply of coal and the necessity for united action, it was deemed best to reorganize the coal-producing facilities in the British zone undor the joint supervision of American and British authorities. As a result, the UK/US Coal Control Group was established accord- ing to the organization plan indicated in figure 2. Headquarters for the group was established at Essen, in Villa Huegol, the prewar home of the Krupp family (fig. 3). One of the many problems recognized immediately by the UK/US Coal Control Group was the necessity of preventing disasters and reducing accidents to work- men in mines undor military-governmont control. Consequently, the United States Bureau of Mines was requested to furnish the services of qualified men to search for the hazards incident to coal mining and to prepare comprehensive reports on the results of their investigations. The authors, who wore selected for this task, spont about a year in Germany and visited all except a few of the smaller mince. Whereas their principal purpose was to investi- gate safety conditions, somo of the operating conditions and practices also wore studied. The results of the studies and investigations are embodied in this circular with the hope that some useful information will be disseminated to the mining industry of the United States, including supervisory officials, safety directors, engineers, and mine workmon.

Feb 1, 1950

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981

By Sheridan J. Rodgers

Toxic fumes generated during shot firing under actual mining conditions were measured. Eight shots with Gelodyn-2X and seven shots with Tovex-100 4VT were monitored. Average CO values for Gelodyn-2X and Tovex-100 4VT were 0.20 ft3/lb and 0.09 ft3/lb, respectively. Average N0x values for Gelodyn-2X and Tovex-100 4VT were 0.049 ft3/lb and 0.026 ft3/lb, respectively. The results obtained with these in-mine tests will be used by the U.S. Bureau of Mines in the development of a large chamber method of measuring fumes from shotfiring of explosives.

Jan 1, 1977

By A. H. Shoemaker

This paper describing the mining practices at the Old Dominion mine, Globe, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various minim districts in the United States. The Old Dominion mine is situated in the eastern port of the Globe-Miami district, about 1-1/2 miles north from the center of the town of Globe. An average of nearly: 1,200 tons per day was mined during 1928. The prevent production is about 1,500 tons per day; of this amount,, approximately 100 tons is direct-smelting ore that is shipped to the smelter at Miami and 1,400 tons milling ore which is treated in the company?s concentrator at Globe. About 600 men are employed at the mine.

Jan 1, 1930

By David C. Oyler, Hakan Gurgenli, Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

By Sean Gallagher, Thomas G. Bobick, William S. Marras

Twelve healthy, experienced underground cool miners performed lifting capacity tests in stooped and kneeling postures using a modified psychophysical procedure. Subjects adjusted weight in a lifting box to the maximum they could handle without undue fatigue in an asymmetric lifting task. Lifting periods were 20 min in duration and the frequency was 10 lifts/min. Tests were performed under a 48-in. roof that restricted the subject&apos;s posture. Psychophysical. physiological, and biomechanical dependent measures included the maximum acceptable weight of lift (MAWL), heart rate (HR), rate of oxygen consumption (VO2), ventilation volume rate (VF), respiratory exchange ratio (R), and integrated electromyography (EMG) of eight trunk muscles. Results indicated that the MAWL was significantly lower when kneeling than when stooped (p < 0.05), Furthermore, metabolic demands were greater in terms of HR (p < 0.005) mid VO2 (p < 0.05) when kneeling. Left and tight erectores spinae muscles exhibited increased EMG activity- in the kneeling posture (p < 0.001). It was concluded that psychophysical lifting capacity is decreased, while the metabolic stress and internal load on the spine are increased, in the kneeling posture. Results of this Bureau of Mines study indicate that it may be advisable to reduce the weight of materials that are handled repetitively in the kneeling posture.