Search Documents

By P. Lozada

The objective currently demanded from controlled blasting techniques is to minimize damage to the remaining rock mass while protecting the integrity of mine walls and ensuring the quality of the fragmented material for easier extraction. Finding this balance represents one of the three main challenges faced by large open-pit mines. They must achieve mine stability by complying with slope designs while also maintaining good results in terms of fragmentation and equipment productivity. The main constraints are related to unfavorable geological conditions, water presence, limited drilling diameters and available explosive products, as well as managing drilling times and blast scheduling, among others. For slope control, in addition to presplitting, blasting designs generally include buffered rows, drilled with smaller diameters, and loaded with fewer kilograms of explosives than production holes. The objective is to reduce the powder factor (kg/t) to minimize the energetic influence on the walls and attenuate damage. However, this often requires using very short charge lengths compared to the bench height (one-third or less) and reducing the pattern geometry, which increases the number of holes per ton and drilling costs. This traditional technique of reducing powder factor in the buffered rows has the main limitation of not being able to distribute the explosive energy throughout the entire column, leading to fragmentation issues mainly in the steaming area. Measurements conducted by Orica in their operations indicate at least a 30% increase in P80 particle size in the buffer zone associated with this condition. To improve energy distribution, techniques such as decking, or vertically decoupled charges can be employed. However, these techniques cannot be applied under wet conditions, and strict control over implementation quality is required to avoid deviations, which increases loading operational times and resource required. In this sense, the use of less energetic and lower-density explosives is a better alternative. On one hand, they allow for complete charge columns in the buffered rows, ensuring homogeneous fragmentation, and on the other hand, they reduce the energetic influence on the slopes, significantly decreasing vibration levels. With less energy per kilogram of explosive (MJ/kg) and less charge per linear meter (kg/m), it becomes possible to handle higher specific charges and longer explosive columns, providing flexibility in drilling and loading design options without compromising slope stability.

Jan 1, 2024

By Dr. Bronwynne Victor, Quentin Steyl, D. Scott Scovira

Bulk emulsions and emulsion blends may be formulated with a single salt, dual salts, or multiple salts. Blasting professionals familiar with single salt ammonium nitrate emulsion products may be less acquainted with dual and multiple salt emulsion products that may include calcium nitrate, sodium nitrate, and urea in their formulations.

Feb 1, 2020

By Gavin Yuill, Kameron Ray

"The impact on vibration model accuracy by input data that is inaccurate was previously unknown, butthought to introduce significant error. This paper explores the impact of accuracy of different GPSreceivers, bulk truck density fluctuations, and charge weight location convention on the accuracy of the final vibration model output. GPS accuracy is compared between a professional Differential GPS, a “prosumer” GPS unit and a standard consumer GPS chip commonly found in cell phones. Bulk truck density fluctuations are compared from the density given by the operator and the actual cup density measured in the field. Charge weight locations explored are from the bottom of the blast hole, center of the powder column, and collar of the hole. The findings show that the weakest link in vibration model creation is actually low seismograph accuracy standards. Errors introduced from such are generally greater than those introduced from other sources."

Jan 1, 2017

By Braden Lusk

This paper includes results from analysis of recorded Acoustic Responses of Structures to Blasting. The analysis was performed to determine specific characteristics of sounds experienced inside homes during blast events. Data was collected in a typical house within the Boone North No.2 Coal Surface Mine in Ashford, WV which was instrumented for several blast vibration and acoustic responses. The instrumentation consists of four acoustic microphones distributed throughout the internal areas of the house and three geophones buried near the house. Two additional channels collect the trigger signal and Air Blast information. For each blast event recorded by the system, the mine blast reports were used to obtain major blast characteristics such as distance from the blast to the instrumented house, weight of explosive used, number of boreholes, delays, and other important parameters. This information allowed study the relationship between the acoustic response and the blast design. From a database of 43 records, five records were chosen for complete analysis. These records were chosen based on distance from the blast to the house, and specific blast parameters. This paper presents the result of the relationship between the frequencies and amplitudes for the entire trace of acoustic records, the response due to ground vibration (GV), and the response due to air-blast (AB). Frequency content was obtained through Fast Fourier Transforms (FFT), using D-Plot software. The records have a typical shape that permits cutting and analyzing each part of the signal with respect to GV and AB separately. Some conclusions are reported concerning the relationship between blast parameters and acoustic response of structures.

Jan 1, 2009

By Jerome H. Stofleth

In June of 1998, the DeBruce Grain Elevator was devastated by an accidental explosion caused by the unintentional ignition of grain dust. The DeBruce grain elevator was the largest ‘single head-house’ grain elevator in the nation. It was comprised of 450 cylindrical grain silos, 30 feet in diameter by 120 feet tall, with a centrally located headhouse. Immediately after the explosion, rescue operations were started for seven missing workers. The Federal Emergency Management Agency (FEMA) had taken over operations of the site by day two. On day three FEMA contacted the Washington DC office of the Department of Energy for explosive expertise, who in turn contacted explosives experts at Sandia National Laboratories (SNL) and Los Alamos National Laboratories (LANL). FEMA was looking for guidance in making the decision to downgrade their operation from a rescue to a recovery operation. Based on some chemical equilibrium calculations, and basic explosive engineering techniques, the SNL/LANL team was able to provide the necessary input to allow the decision to be made for the operational downgrade. At this point, only one worker remained un-recovered.

Jan 1, 2004

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

Jan 1, 2004

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By Dale Preece, Vanessa Berg

This paper presents a two-pronged vulnerability analysis approach for treating minimally reinforced concrete (RC) structures subjected to explosive events. This work was motivated by a heightened interest in homeland protection involving both malevolent and accidental explosions and the need for assessment of critical facilities subjected to an explosive detonation. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN, while the second part of the analysis employs Single-Degree-of-Freedom (SDOF) methods, each predicting the dynamic response of the minimally RC walls, slabs and columns to explosive loading. The concrete is treated with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model, which accounts for failure mechanisms in brittle materials. Predictions from AUTODYN are verified using the equivalent SDOF reinforced concrete code, SPAn32, developed by the US Army Corp of Engineers and agreement between the results indicates a high level of accuracy in both methods of analysis, allowing for accurate predications of airblast-structure interactions and failure mechanisms.

Jan 1, 2004

By Robert Cefalo

Drill and Blast Engineer Abstract In 2019, the Bingham Canyon Mine, owned by Rio Tinto Kennecott Utah Copper Company, mined through the active underground that dewaters the pit. The active underground required the limitation of vibrations to avoid catastrophic damage or damage that would require work to the shotcrete and additional roof support. The surface design of the current sector next to and through portions of the active underground. The drill and blast group was required to test site law vibration parameters to ensure that vibration limitations were lower than limits set by the underground management team. Seismographs were used to validate the vibration prediction model and check performance of blast in areas of the underground. The bench conditions and limited pounds-per-delay created large obstacles for the blasting team, making it difficult for them to accurately load the pattern with the number of decks in the blast. Methods were used to improve the loading instructions and ensure that each hole achieved pound requirements based off of the distance to the underground that it was designed to protect. The project evolved from start to finish, and the process to estimate distances and loading improved to make the blast a more repeatable process for the size of the project.

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By Nolan Eckroade

The demand for blast optimization within the quarrying industry calls for more effective, faster and safer methods of quantification of blast performance. Drones provide the ability to safely and quickly capture high resolution imagery of a muckpile for use in fragmentation photo analysis. Oversize material within a muckpile is an expensive and universal problem affecting quarries, especially in situations where cap rock is present. Although the amount of oversize material in a blast is a key indicator of blast performance, it is difficult, hazardous and slow to measure across an entire muckpile using traditional methods. By piloting a drone using an automated flight plan with set amount of overlap across images, the images can be processed into a single, high resolution orthomosaic image for use in fragmentation photo analysis software.

Jan 1, 2018

By Chuck Kliche, Bill Clements

This project involved the removal of the top of an old water supply reservoir tank for the City of Lead, SD by explosives. The general contract called for the removal of the concrete top without damaging the sides or floor of the reservoir. The option of a rock hammer was eliminated, due to the possibility of an unpredictable collapse damaging the sides or floor of the reservoir. Different blasting options were discussed between the primary contractor and the blasting contractor, along with the pros and cons of each. The primary contractor settled on the option of drilling the structure for blasting versus using shaped charges

Jan 1, 2007

By Earl C. Hutchison, Wade C. Hutchison

To effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre and post blast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By Z X. Zhang

In sublevel caving mines, eyebrow break usually gives rise to lower ore recovery and worse safety in the field. Eyebrow break is caused mainly by two tensile stress waves: one from the front surface of a blasting ring, and the other from the roof of the drift. In order to reduce the two waves and finally to reduce eyebrow break at Malmberget mine, we employed two methods: (1) cartridge charge, and (2) double-primers in each blasthole. The two methods were tested in one ore body called ViRi. A total of 10 rings with the cartridge charge and 25 rings with the double-primers were blasted. At the same time a total of 34 ordinary rings were blasted in the same ore body. The result shows that the eyebrow break is 3.0 m for the ordinary rings, 2.3 m for the cartridge charge rings, and 2.1 m for the double-primer rings, respectively. In addition, the ore recovery for the double-primer rings is increased by 3% on the level of ViRi930, compared with that for the ordinary rings.

Jan 1, 2011

By Per-Anders Persson

TIGERWIN, now on CD, is a user-friendly personal computer code (running under Windows) which determines the detonation and expansion state of an explosive from its known chemical composition. TIGERWIN is intended for users in the mining and commercial explosives industry who do not routinely program or run Fortran codes. The code allows the user to open a window on the computer screen and enter the initial density and the weight percentage composition of an explosive, ingredient by ingredient. Alternatively, the code can balance the composition with one or more ingredient percentages fixed, while proportionally adjusting the others automatically to give a total of 100%. The equation of state and its parameters can be user-selected from several proven and tested versions of the BKW, the JCZ, and the ideal gas equations of state. TIGERWIN allows the user to select several options for different additional calculations, such as determining the constant volume explosion, the Chapman-Jouguet (C-J) point, the detonation Hugoniot, the expansion isentrope from the C-J point, and point calculations with selectable specific volume and temperature. Additional options include calculations of detonation data with one or more ingredients partially reacted, assuming either temperature equilibrium between reaction products and unreacted material, or keeping the unreacted material “cold” at the initial temperature. Thus the code can run both ideal and non-ideal detonation calculations. The code automatically saves the input and output files in a separate directory for future reference. The output from several calculations can be displayed and printed in the form of a comparison table. In it, the key results of up to five calculations with different explosive compositions can be compared. The results from an individual calculation can be displayed graphically and printed with expansion work, pressure, or temperature as functions of specific volume. A complete listing of the details of the calculation results, similar to those from the original Fortran Tiger calculations, can also be displayed and printed. No computer experience is required to run the code and workshop participants are encouraged to bring in their own formulations to try out on TIGERWIN

Jan 1, 2000

By Paul Worsey, Seokbin Lim

In many high explosive applications, the explosives are covered or clad by a metal. This metal cover may serve a variety of purposes including: 1) to protect and prevent the disturbing or misshaping of the explosive during its transportation, handling and use, 2) in many military applications the cover material itself is used to provide a required effect, for example, the shrapnel from grenades, the metallic liner of shaped charges, and the confinement of explosives so they perform optimally, and, 3) in civilian applications in the use of well perforating shaped charges and linear shaped charges used for the demolition of steel structures such as bridges. For these reasons the interactions between the explosives and their covering materials are of great importance in understanding the performance of these devices.

Jan 1, 2005

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By James G. Stuart, Tassilo N. Baur

We will discuss the kind of procedure that we use to predict the no-fire (for safety) and all-fire (for reliability) current levels for any given type electric detonator. The basic idea is to expose several detonators to different levels of electric current, so we can estimate the probability of firing as a function of current. We call this a statistical firing test. But what about the uncertainty in measuring the current? Suppose we are not quite sure what stimulus level we apply? This is the question that we will consider here. This relates to both safety and reliability. Surprisingly enough, we will find that some uncertainty in measuring the levels during our statistical firing test improves our long-term safety and reliability

Jan 1, 2019

By Harry Verakis, Thomas Lobb

Widespread use of ammonium nitrate compositions for mine blasting operations has led to various bulk transport vehicles designed especially for the explosives industry over the past half century or more. The advancements in explosives technology and continuing developments in bulk transportation have resulted in a variety of blasting agents and, more recently, oxidizers being transported and used from specially designed bulk transport vehicles. It is estimated that about 2000 bulk transport vehicles are used in mining operations. Many of the bulk vehicles carry about 15,000 to 33,000 pounds (6808 to 14,968 kilograms) of payload and some can carry up to 50,000 pounds (22,679 kilograms) for large open cast mines. Thus, it is imperative that detailed knowledge and safety instructions are available from the blasting personnel and mine management should an unplanned incident such as a fire occur with a bulk transport vehicle at a mine site.

Jan 1, 2008