Search Documents

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

By D Rubery, C Croker

The Boddington Gold Mine (BGM) is located 120 km south east of Perth, Western Australia. The operation is managed by Worsley Alumina Pty Ltd and mined by contractor Henry Walker Eltin (HWE). The mine has been operating since 1987 with ore extracted from a series of pits along strike. Ore is contained within the basement rock, which is overlain by a cap rock layer and transition zone. Cap rock and basement zones require blasting.As the mine neared completion, a high-grade deposit was discovered within 50 m of an existing Western Power substation and 100 m from the processing mill. The substation provides power to the Boddington area and is a back-up power supply to the city of Perth. Due to the delicate nature of the transformers located at the power station, overhead power lines and the mill, blasting in the area was considered very high risk. As such blasting needed to be controlled for flyrock, airblast and most importantly peak vibration and frequency limits which had the potential to damage the transformers.The mine was due for closure in March 2001. The decision to mine the pit was based on its high grade, ability to be blended with lowering grades from other pits and changing of the processing technique with the expansion. This decision extended the life for a further six months.Due to the high potential risks a detailed risk assessment was conducted by Orica, Worsley and Henry Walker Eltin. The completed assessment and the major design parameters were presented to Western Power for approval. The ability to reduce the blasting risk was focused on limiting of vibration through controlling maximum charge initiated per delay, blast timing and firing direction, and other innovative control measures. OricaÆs SHOTPlan« and Sabrex« computer modelling packages were used to predict the outcome of blasts.The success of this project has opened the doors for other high risk blasting projects, which otherwise may be left unmined.

Jan 1, 2002

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

By M Sherman

The challenge facing the engineering provider is to calculate throughput rates when faced with disparate specific energies calculated by different testing methodologies. Typically, an ownerÆs team would expect that the throughput calculations be checked using more than one method, therefore it is inevitable that there will be differences, based on which methodology is used. This engineering challenge is exacerbated by the continuing evolution of contemporary circuit configurations such as two stage pebble crushing with or without high pressure grinding rolls (HPGRs) as the second stage, or second stage pebble crusher product reporting to the ball milling circuit, etc.This paper is a companion to the paper first presented at SAG 2011, which showed that the Bond Indices are an excellent tool for estimating the specific energy requirements for semi-autogenous grinding (SAG) mills in single-stage SAG milling (SSS) circuits, SAG and ball mill circuits (SAB) or SAG and ball mill circuits with pebble crushers (SABC). This paper presents how the Bond Indices have been used to calculate ball mill specific energies, and therefore throughput rates, for SAG mill based circuits. Once the ball milling specific energy is known, tower mill and vertimill energy requirements can also be calculated. It is noteworthy that the method presented in this paper does not require the use of any unpublished correction factors: the proposed method uses the Bond parameters and equations published by Rowland in 1982.CITATION:Sherman, M, 2013. 21st century bond, in Proceedings Iron Ore 2013 , pp 309-312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D Garcés, M Meléndez, R Castro, E Viera

Enhancing the understanding of gravity flow in caving operations is a key factor in the design, operation and success of caving methods. Consequently, much research has been performed to increase knowledge about gravity flow. Many valuable theories have been gained from different research approaches, which include physical modelling, numerical modelling and a limited number of full-scale tests. Recent advances in technology have allowed Codelco Chile to carry out trials using Smart Markers technology. This technology was used in Esmeralda mine’s Block-2 at El Teniente mine from August 2012 to January 2015. This paper aims to determine the characteristics of the extraction zone and obtain the data that will allow greater understanding of gravity flow for design and draw control purposes.The collected data from recovered markers were analysed using a linear interpolation of both the initial position of the markers and drawbell accumulated drawn tonnage. For each drawpoint in the trial, the regularity or irregularity of flow was analysed based on the recovered markers and the drawn tonnage. Correspondingly, the relationship between flow characteristics and observed fragmentation in drawpoints was analysed. The gravity flow of the Smart Markers revealed that current drawpoint spacing provides the interaction conditions of adjacent flow zones. However, it is possible to increase the drawpoint spacing while allowing caved rock to be extracted from the major and minor apexes.The results of this research also verified that full-scale test data are the predominant factor in the production level design and production control at El Teniente mine.CITATION:Garcés, D, Viera, E, Castro, R and Meléndez, M, 2016. Gravity flow full-scale tests at Esmeralda Mine’s Block-2, El Teniente, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Size Separation Pretreatment and Alumina Recovery from Bayer Red Mud

Sep 13, 2010

Procedures employing thiocyanate and dithiol complexes of molybdenum have been developed for the determination of the metal in the presence of large quantities of ferric iron. The procedures are developed for field application and it is possible to complete 200 analyses per day with laboratory accuracy. Use is made of sulphuric acid extraction and ascorbic acid reduction in the case of the thiocyanate procedure whilst the reducing system in the dithiol procedure is potassium iodide-sodium sulphite. Using a simple photometer the range of determination possible is 0-10~g for the thiocyanate procedure and 0-5 g for dithioI.INTRODUCTIONOf the many colorimetric procedures that have been developed for the determination of molybdenum only those using the thiocyanate or toluene-3, 4-dithiol complexes of the metal are sufficiently free from interference to be of use in geochemical prospecting. Rapid methods based on both these complexes 'have been developed at the. Broken Hill Division of The University of New South Wales as part of a general programme designed to improve geochemical procedures. Whilst speed rather than high accuracy is the important factor in prospecting, the aim of the programme is to develop procedures which will allow determination of 200· samples per man-day without loss of normal laboratory accuracy for the methods concerned.In most geochemical procedures visual estimation of a coloured complex is used in the determination of the quantity of metal present. At the high rate of sample determination of the improved methods this procedure places severe strain on the eyes. For this reason all methods are designed for determination by means of a simple filter photometer...

Jan 1, 1965

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Met M, Worner H. K

In pursuance of the investigation into the influence of various elements on the properties of lead during the past year, the effect of several elements on the creep rate of commercially pure lead has been investigated; a standard initial stress of 500 lb. per sq. in. having been adopted for comparison purposes. Other work which has been carried out indicates that the relative results of creep tests may be altered by varying the applied stress, but this aspect of the problem will need to await further investigations for itscomplete elucidation. The results obtained with dilute tellurium alloys are considered sufficiently interesting, and in some respects are so extraordinary, as to warrant publicatiorr at this stage.n must be realised however that, since the results obtained appear to be at variance with those said to have been obtained in practice and those previously published, the present investigation can only be considered as a contribution to our knowledge of the general problem.Consequently it is not considered advisable or necessary to offer detailed explanation of the results given. In fact, some features of the tests about to be described will need further investigation before an adequate explanation is possible.

Jan 1, 1936

Effect of Anionic Surfactant on Silica Particle Attachment at the Oil-Water Interface Controlling particle attachment is crucial where powdered solids come into contact with oil and water. Particles are trapped in a deep energy well at the oil-water interface, stabilising emulsions. Here it is shown that adding anionic surfactant causes dramatic changes to the bulk and interfacial structure of silica particle-stabilised oil-in-water emulsions. Exposing particle-stabilised drops to surfactant concentrations above the critical micelle concentration enhances the rate and extent of creaming and flocculation. Mixing particle-stabilised emulsions with surfactant solutions causes drop fragmentation. As the surfactant concentration increases, the average drop size decreases and particles are displaced from the interface during the mixing process.

Sep 13, 2010

By J L. Mauk

 Broken Hills is an adularia-sericite epithermal Au-Ag deposit, hosted in flow-banded rhyolites and overlying rhyolitic pyroclastic rocks in the eastern Hauraki Goldfield. The 7.1 Ma deposit was the largest producer of gold in the eastern Hauraki Goldfield, and was one of very few economic deposits hosted in Pliocene rhyolites. This paper presents the results of a recent study in the upper levels of the deposit. Maps and cross-sections constrain structural and lithological relationships, and the lateral and vertical extent of a breccia pipe û the major feature of the upper levels.   Previous studies in the upper levels of Broken Hills have shown that gold and silver values are concentrated around and within a large breccia pipe, mined by a series of æcaveÆ stopes and in veins. Contour diagrams of Au-Ag data from channel samples indicate that the breccia pipe was a major fluid channel-way for mineralising solutions.   The breccia pipe deposits are part of the dynamic geothermal system that formed the Broken Hills ore bodies; they developed as a result of hydrothermal brecciation in areas of structural weakness within a rhyolite pyroclastic unit that overlies a massive rhyolite lava-flow unit. The main breccia pipe begins near the rhyolite/pyroclastic contact, having the shape of an inverted, inclined cone, and consists of silicified breccia, stringers of quartz, and irregular patches of clay-altered country rock. Smaller zones or pockets of hydrothermal eruption breccia are silicified and contain low grade gold in the matrix and in the adjacent silicified wall rocks.   Quartz has been classified according to its physical characteristics as seen in situ and hand specimens indicate that vein definition decreases upwards, perhaps as a result of changing lithological conditions and/or increasing proximity to the paleosurface. Hydrothermal quartz is widespread as veins and as a replacement mineral, or lining fractures and cavities and overgrowing rock fragments. Breccias contain vein quartz, but some quartz veins cross-cut breccias, indicating that vein and breccia formation was relatively synchronous and overlapped in time.   Disseminated gold-silver mineralisation is associated with vein quartz and silicic alteration of the wall rock within the breccia pipe. The auriferous zones are highly irregular and erratic, and sampling results show a wide range of gold-silver ratios, suggesting that highly volatile physiochemical conditions prevailed during mineralisation.

Jan 1, 2005

By M J. Shearer

An investigation into the reliability of the data being collected at the Mount Isa Mines site operated by Glencore in Queensland allowed on-site ventilation personnel to scrutinise pressure and volume measurements collected from the primary surface fans. The investigation effectively identified discrepancies being reported to the on-site remote monitoring system. The difference between the real-time and static measurements on the P63 RAR shaft identified that the in situ differential pressure transducer and piezo annubar system was not operating correctly. This indicated a deficiency of approximately 30 per cent reporting back to the remote monitoring software versus the live readings measured with the Pitot tube bomb and ALNOR AXD610 pressure micro-manometer.Constant monitoring of an operations ventilation network is imperative to ensuring that the underground atmosphere provides a safe and healthy workplace. Further benefits to real-time monitoring allows for the early indication of network failures and promotes increased availability. An innovative approach to out engineer and improve the existing measuring equipment from the 1970s was sought.The use of ultrasonics in the mining industry is not new with ventilation management systems (VMS) equipment available within the marketplace. The introduction and implementation of a reliable product for real-time monitoring was a challenge to overcome due to limited access and suitable measuring points within the mine. The available equipment on the market through mainstream suppliers was not suitable for the unique application required due to the in situ installation of the surface fans. A solution was identified in the oil and gas industry through collaboration and innovative thinking. This paper describes the sustainable approach to implement a reliable air flow monitoring system on-site.CITATION:Shearer, M J, 2017. Case study – an analysis of reliability and efficiency: ultrasonic versus annubar technologies, in Proceedings Australian Mine Vent Conference 2017, pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Effect of Bulk Iron Concentration on the Copper Activation of Sphalerite at pH 9

Sep 13, 2010

The mineralogy and textures of a portion oC ore from the 25 level northern orebody, North mine, Broken Hill are described. This ore, in places, contains up to 70 per cent cubanite (CuFe2S3 ) which has crystallized directly with other sulphides and associated gangue minerals.Several breakdown reactions involving the cubanite are also considered.

Jan 1, 1969

By G F. Brent, R D. Hart, C Carr, F Felipe

In underground operations, where copper, gold and other metals are mined, the open stopes can be backfilled to stabilise surrounding workings. This fill may consist of tailings from the processing plant, usually mixed in slurry with a binder such as ordinary Portland cement (OPC). Extensive use is made of tailings in OPC-based paste fill, cemented hydraulic fill or cemented aggregate fill applications. A large underground operation such as the Mount Isa Copper Operations utilises over three million tonnes of backfill per annum. Geopolymers offer an alternative binder system with significant environmental advantages over OPC. Geopolymers are formed by polymerisation of aluminosilicate precursors in an alkali medium. They generally form products with superior strength characteristics as well as increased resistance to degradation, particularly under acidic conditions. Geopolymers have lower carbon dioxide emissions associated with their manufacture than OPC and offer further potential advantages, such as the use of less water and more waste materials. The application of geopolymers to weak material systems such as mine backfill has not been widely studied. The aims of this investigation were to assess a range of Australian mine process wastes for suitability as feedstocks in fill applications and to construct a range of these cemented minefills using a geopolymer binder. The physicochemical characteristics of each of the wastes are discussed as well as how they ultimately contribute to the geopolymer cement through direct replacement of OPC. Results from various tests on the candidate geopolymer fill formulations are presented and the potential of such fill formulations to replace OPC in mine backfilling operations is highlighted. The significant potential contribution to reducing greenhouse gas emissions from the use of geopolymer-based mine backfill across the industry is noted. Conversion of a single mine, such as the Mount Isa Copper Operations, is shown to match the reductions in greenhouse gas emissions due to the current total installed photovoltaic electricity generation capacity of Australia. A similar examination of wastes available to a gold mine could potentially yield new binders for use in established or new fill systems.

Jan 1, 2007

By Holmes R. J, Miles J. G

An on-stream shale detector has been developed that is suitable for use on conveyor belts carrying iron ore of up to 200 mm particle size. The shale is distinguished from high-grade iron ore by means of the substantially greater total natural gamma-ray activity (400-3000 keV) of the shale, which is due to the presence of uranium (214Bi), thorium (208TI) and potassium (40K). Other gangue materials, sueh as highly siliceous cherts and jaspilites, escape detection because of their low activity. A dynamic trial of the shale detector at Mt Whaleback, using a large-volume (100 × 100 400 mm long) "Polyscin" Nal(TI) gamma-ray detector, demonstrated that as little as 20 tonne of ore on a conveyor belt (equivalent to partial truckloads of ore) can readily be monitored for shale content.

Jan 1, 1981

A New Online Detection Method for Arsenic Minerals in Process Streams

Sep 13, 2010

A summary of a proposal to develop a 20 000 tpa underground gold operation in a Forest Park. The environmental constraints are severe and affected the mine development planning and choice of mining method. The mine will use trackless methods to access the narrow 1.5 m ore shoots, and to mine ore by cut and fill methods. The use of Microscoop and CT 1700 HE electric LHDs for mucking, together with special drilling attachments for drilling, is central to efficiency and small Kubota diesel haulers will be used for carrying ore to surface.

Jan 1, 1986