Search Documents

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By AIME AIME

Change of Meeting from Birmingham to Chattanooga. In consequence of the disturbed conditions attending a long¬continued labor strike in Alabama, the meeting of the Institute was changed from Birmingham, Ala., to Chattanooga, Tenn., where it will. begin on Thursday evening, Oct. 1, 1908. Information. of this change bad been sent to the newspapers through the Associated Press, and by circular to all members, when news was received of the sudden and unexpected termination of the strike referred to. It was, unfortunately, too late to change once more the arrangements for the meeting. But it is hoped that the cordial invitation of the citizens of ,Birmingham may be renewed and accepted at a future time, not too remote. Office Facilities for Visiting Members. A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the temporary use of members of the Institute or of sister societies, or visitors suitably accredited. Members of the Institute visiting New York for a short time, who need office facilities during their stay, or members residing in the city. who need temporary office accommodation, can arrange to have set apart for their exclusive use a room, equipped with office furniture, telephone, etc.,. in the suite of the Institute. It is not the intention to give possession of the room to any individual for an indefinite time, but to offer to members of the Institute an opportunity to acquire a well-located, well-equipped business headquarters to carry on transactions which

Jan 9, 1908

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By Carl Henrich

Jan 1, 1893

By I. C. Edwards, G. E. Agar

INTRODUCTION Many research efforts over the past years have been devoted to the study of energy consumption in comminution and the characteristics of the broken material. The old "laws" have been superseded by more general methods of analysis1,2,3 but these methods have not received much attention outside the laboratory. The work to be described here was done in order to obtain scale-up information on wet rod milling of sylvinite. EXPERIMENTAL A 30 x 51 in. Denver rod mill with a scoop feeder was used for these tests. Ore was fed from a variable speed screw conveyor into the feed box along with saturated brine. The mill was filled to approximately 45% of its volume with 2400 lbs of a mixed rod charge. The minimum possible feed rate was 2.5 tph and the practical maximum for this mill was 8 tph. Individual tests were run by setting the solid feed rate, then adjusting the brine flow rate to give the desired pulp density. After steady state, as evidenced by constant discharge pulp density, had been reached, samples of the discharge were taken at 15-minute intervals. These samples were filtered, washed with alcohol, dried, then screened on Tyler screens using a Ro-tap shaker. The sylvinite feed was regular plant feed that had been scalped at 20 mesh and was tapped from the coarse ore bins. It had been previously passed through a roll crusher set at 3 inches and after scalping was essentially minus 1 in. plus 20 mesh. RESULTS The screen analysis of samples from each series of tests was plotted on double logarithmic scale paper to determine the reliability of the series. In some cases, a faulty sample or screening procedure dictated that the results of one test be discarded. The criterion is a simple one — if the slope of one plot was noticeably different from the others in the series, it was discarded. The only cases that caused difficulty were those in which the brine was not thoroughly displaced from the solids. When this occurred agglomerates were easily identified on the screens and the whole of the sample was retained on 3 or 4 screens. There were no border line cases. The number N given in Table 1 is the number of size analyses that were pooled to form the data shown in Fig. 1. While examining the reliability of the sizing and sampling by plotting the data, it became apparent that there was no significant difference between grinds made at 50 and 60% solids. For the analysis given here, these tests were regarded

Jan 1, 1967

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant&apos; have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh&apos;s work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-&apos; and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

Organization Place Date 1919 American Railway Engineering Association Chicago, 111. Mar. 18-20 Society of Industrial Engineers New York, N. Y. Mar. 18-21 American Electrochemical Society New York, N. Y. Apr. 3-5 National Foreign Trade Council Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y. May American Institute of Electrical Engineers Lake Placid, N. Y. June

Jan 3, 1919

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever&apos; and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell&apos;s heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,&apos;, steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell&apos;s part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O&apos;Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O&apos;Brien&apos;s paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

By F. C. Langenberg, J. Chipman

Jan 1, 1959

By J. Spotts McDowell

Ackowledgments........................... 5 Introduction............................. 5 The Silica Minerals. Stability Relations......................... 6 Optical Properties........................ 9 Density.............................. 10 Melting Points....;..................... 10 Thermal Expansion..................,..... 10 Solubilities............................ 12 Identification of Cristobalite and Tridymite.............. 12. The Silica Refractories. Raw Materia1........................... 13 American Deposits....................... 13 Properties Determining Usability................ 15 Expansion on Heating..................... 16 Texture........................... 17 Silica Brick............................ 17 Manufacture........................... 18 Properties of Silica Brick .................... 19 Analysis ......................... 19 Density......................... 19 Porosity......................... 20 Strength....................... 21 Melting Point....................... 22 Specific Heat....................... 22 Thermal Conductivity................... 23 Expansion........................ 24 Effect of Rapid Temperature Change.........:... 26 Constitution......................... 26

Jan 1, 1918

Jan 1, 1971