Search Documents

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

G. R. Compton (Gold Mines of Kalgoorlie (Australia) Ltd., Fimiston, W. A.) : In congratulating Mr. Hooker upon his resume of Mr Parry's paper I have in mind the fact that he carried out the research into pipe pressures. Hydraulic filling as practised in Kalgoorlie has created world wide interest, with these pressures and percolation being vital points.Early in the 1950s, representatives of the Kolar field were conduGted over the local mines where stopes at depths below 2,000 ft were being filled. The problems of pipe pressures were their main consideration since depths of up to 10,000 ft were envisaged.Mr Krishnaiah and Mr Murthy from the same field are with us today and perhaps we may hear of their experiences with depths of 6,000 ft and long lateral lines.J. Holly (Lake View and Star Ltd., Fimiston, W.A.): There is one phase, which I would like to mention myself, that has been very evident in Kalgoorlie operations. That is, we do not get the percolation properties that are obtained on many other fields in the world, and our tendency here has been to assess the quality of our fill more by its settling rate, i.e. the rate at which we can draw off clear water at the surface of the filling levels, rather than the rate that this water percolates down through the fill before it consolidates.We are tending now to measure the quality of our fill as a settling rate rather than as a percolation rate.Americans talk about percolation rates being the important property: If anyone has any experience on operating with fills with different percolation rates, I think their views would be very interesting to the meeting art this stage. Mr ...

Jan 1, 1965

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

By É. Roberge, S. Makni, G. Gagnon, F. Lavoie, A. Faucher

"Feed particle size is an important variable for the primary grinding mill operation. Several commercial vision systems have proven to successfully measure online many types of ores and are used for automatic control. However, due to limitations associated with segmentation algorithms, these systems fail to provide good measurements when the feed is composed of a specific bimodal particle size distribution: very big rocks and a large amount of fine particles. This is typically the case for crushed iron ore. This paper presents a technique to overcome the limitations of existing vision systems by using 3D cameras and appropriate processing methods. It provides online particle size distribution indicators and bulk volume flow rate measurement. It is designed to be very cost-effective, robust, precise, easy to install and to maintain. The 3D system was validated in two iron ore processing plants and the results clearly show that it can be used to optimize primary grinding mill operation where 2D segmentation vision systems fail.INTRODUCTIONFragmentation measurement using digital image processing has successfully been applied in mining and mineral processing operations. Several maintenance and operating applications are already deployed in the industry: Measurement of rock fragmentation after blasting (Maerz, 1999; Palangio, 1999) (Pragyan, 2012) Truck inventory (Palangio, 2005) Monitoring of crusher mantle wear Automatic control of crushers and SAG mills (Bouajila, 2000) (Bartolacci, 2001)Commercial technologies like WipFrag (Maerz, 1999), VisioRock and others proved to be very efficient to precisely measure the particle size distribution of many types of materials. These products are mainly composed of a camera, a lighting system and an image processing system based on a segmentation algorithm. By controlling adequately the lighting conditions and with periodic maintenance on the segmentation algorithm calibration parameters, it is almost always possible to achieve reliable measurements.However, the segmentation algorithm is not adequate when the particle size distribution contains big rocks and a large amount of fine particles. In this case, the area containing the fine particles is accounted as a big rock while big rocks get segmented as multiple smaller sized particles, leading globally to a wrong measurement. This situation prevails for crushed iron ore and coke, among other materials. Figure 1 shows a picture of a material which is typically very difficult to process through segmentation techniques."

Jan 1, 2015

By P. Pyykkö, E. Peuraniemi, J. Järvi, P. V. Latostenmaa, V. Törölä, S. Junnikkala

"Nickel concentrate smelting started in Harjavalta in 1959. First, flash smelting - Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes. In 1995 the original smelter flow sheet was simplified with the novel DON (Direct Outokumpu Nickel) technology. In Harjavalta with the DON technology, high-grade nickel matte with low iron content is produced in flash smelting furnace directly without subsequent converting stage. The metal values in the smelting slag are recovered in an electric furnace as an iron containing bottom alloy. Main special features in Boliden Harjavalta nickel smelter are smelting of high-magnesia concentrates, the high recoveries of nickel and copper, as well as those of PGM`s and cobalt.Sulfur and dust emissions to air can be seen generally as one main disadvantage of nickel smelting operations. In Harjavalta continuous improvements in environmental performance has been rewarded by minimum sulfur and dust emissions to the environment and working atmosphere. Today Boliden Harjavalta’s nickel smelter is presenting state-of-art-technology at nickel smelting.This paper describes the nickel smelter process and includes recent production and emission data. It describes features required to achieve environmental and occupational hygiene goals and compares environmental performance data to that published on other smelting operations. General description of New Boliden Way is presented and a case example of production stability project is also presented."

Jan 1, 2014

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By M. Hancer, J. D. Miller

It is known from soluble salt flotation practice that the K, Mg double salts of kainite (KClMgSO43H2O), and carnallite (KClMgCl26H2O) are difficult to float and must be converted to other salts such as schoenite (K2SO4MgSO46H2O) and sylvite (KCl) in order to recover potash values. The flotation characteristics of these double salts have now been confirmed in some detail by carefully controlled laboratory experiments with both cationic and anionic collectors. The experimental results are discussed in view of recent experimental findings regarding the flotation characteristics of simple salts, in which the flotation response was shown to be determined by the interfacial water structure and whether the salt could be considered to be a water structure maker or a water structure breaker. The same approach can be use to explain the flotation response of the potassium double salts ; schoenite, kainite, and carnallite. In addition, the sign of the surface charge of schoenite (K2SO4MgSO46H2O), was determined as a function of pH from nonequilibrium electrophoretic mobility measurements. Schoenite appears to exhibit three charge reversals (CR) which can be explained based on surface hydrolysis reactions. The flotation behavior of schoenite is further considered based on solution chemistry calculations, electrophoretic mobility measurements, and microflotation results.

Jan 1, 2001

Rutile Beach Sand from Hard Rock

Sep 13, 2010

By Michael A. Knott

Large lateral forces on bridge foundations due to extreme events such as vessel collisions, earthquakes, and wave forces on storm surges during hurricane events are often the controlling design condition for bridge foundations. A review of the American Association of State Highway and Transportation Officials (AASHTO) vessel collision analysis and design codes used in the United States for highway bridges will be presented. The paper includes the background and development of the AASHTO Guide Specification and Commentary for Vessel Collision Design of Highway Bridges (1991) and vessel collision provisions of the AASHTO LRFD Bridge Design Specifications (3rd Edition 2004 and the approved 2005 Interims). Experience in using the AASHTO codes will be discussed and observations on the adequacy and gaps, comparison with the European Standard Code, and recommendations for immediate and long term needs will be presented.

Jan 1, 2013

By Philip Thompson

Many new evaluation tools have been developed since the early 1990’s to aid the minerals processing test engineer. The areas of comminution, gravity concentration, flotation, and process mineralogy have received particular attention. This paper will describe new laboratory procedures in the areas of SAG mill testing, gravity concentration, and flotation testing. Computer assisted mineralogical examination equipment, new generations of mass balancing programs, and simulation programs will also be discussed.

Sep 12, 2005

By P L. McCarthy

In an environment of accelerating capital costs, limited capital availability and strongly cyclic metal prices, there is a difference between a robust mining and processing operation and one that would maximise shareholder returns in an idealised world. A higher cut-off grade policy is likely to improve operating margins and may reduce the scale of operations and thus limit capital exposure. This will leave some metal in the ground, but it is marginal material which carries the greatest cost and risk exposures. Where do we draw the line?CITATION:McCarthy, P L, 2013. Is bigger better? Building market resilience into process plant design, in Proceedings MetPlant 2013 , pp 66-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Dennis W. Boehm

The building boom of the late 1970's and early 1980's has all but used up most of the better sites across the more populated metropolitan areas of the United States. This means that current buildings and other types of structures are being founded on more marginal sites. The use of marginal sites has placed ever-increasing quality control on the installation of the deep foundation systems utilized for these sites. Several remedial techniques are available for the repair of the deep foundation systems. These include minipiles, compaction grouting and jet grouting. Eight case histories are cited where these methods have been utilized to repair deep foundations.

Jan 1, 1999

Situated in the Greymouth Coalfield, the Mt Davy Block contains a significant resource of high quality bituminous coal suitable for use in metallurgical coking coal blends. The coal, which is all low sulphur, is seen as a complementary deposit to export coking coal at Stockton Mine.   Previous drilling by State Coal Mines (1948 - 1953) and Japanese interests (1970's) have been supplemented by Coal New Zealand drilling (1992 - 1993) and surface mapping. A mining feasibility study was completed in late 1993 and approval gained for the driveage of an exploratory tunnel to the target seam.   Following construction of surface facilities, tunnel driveage on a 1:5 decline commenced from Rewanui in May 1995 and to date about half the required length has been driven. When the seam is intersected a comprehensive geotechnical testing programme will be undertaken to assess the in-situ mining conditions. It is expected that the results will confirm the assumptions made in the feasibility study.   The Mt Davy Mine, at depths of 500 - 700 metres, will be the deepest underground coal mine ever inNew Zealand and in-situ stresses (orientation and magnitude) will be important considerations for mining engineering. The coal has a high gas content and suitable techniques for gas control and prevention/mitigation of coal outbursts will be necessary.   Mine development is scheduled to commence in mid 1998 and an annual production level of 500 000 tonnes is forecast. The coal seams will be developed by continuous miner and coal extraction will be by hydraulic monitor. Coal will be pumped to the surface and from Rewanui transported five kilometres to Dunollie either by truck or slurry pipeline. At Dunollie a coal dewatering plant, coal stockpile and rail loadout will be constructed.

Jan 1, 1996

THE method depends upon:--1. The position of the mill.2. The space available for stacking the residue.3. The nature of the residue as discharged from the mill.4. The value of the residue for re-treatment.5. The requirement of the residue for underground filling.Originally the conditions in this district varied mainly in the position of the mill, some mills having an elevated site with plenty of dumping space for the time being, whilst others had a flat site, and very little dumping space near at hand; but in most cases the residue discharged was in the form of filter-press cakes, suitable for conveying on belts, or in trucks, and stacking in a high clump; and, while a portion of the residue was used for underground filling, the dump was regarded as a valuable asset, to be re-treated later. Under these conditions, conveyor belts, electric trams, aerial trams, and hose trucks, all gave satisfactory results, and the following figures, taken from "'West Australian Metallurgical Practice," will show how these methods compared as regards costs...

Jan 1, 1909

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By C E. J de Ronde, I C. Wright

Oceanic subduction-related volcanic frontal arcs extend over 20 000 km within the western Pacific basin and over 21 500 km worldwide, yet they remain largely unexplored with respect to active seafloor mineralization. Systematic exploration of 26 major submarine volcanoes along ~840 km of the Kermadec arc northeast of New Zealand has documented ten (39 per cent) as being hydrothermally active. This frequency of venting is comparable to that on slow-to-moderate rate spreading mid-ocean ridges, which comprise ~80 per cent of the 60 000 km-long global system of spreading centers. The chemistry of fluids discharged from the Kermadec arc volcanoes is moderated by magmatic components in both the gaseous (CO2 + SO2-H2S) and liquid (Fe) phases at very high concentration.The high frequency of venting coupled with chemically rich discharge discovered during this first systematic survey of any arc system forecasts submarine arcs as being important sources of chemicals to the oceans and as potentially lucrative exploration sites for seafloor mineralization. The exploration protocols developed during these surveys include bathymetric mapping of mostly unknown volcanic edifices, followed by detailed water column profiling and sampling to detect and characterize volcanic fluid emission signatures. These procedures are being refined as the survey progresses, both for efficiency and as direct seafloor observations become available for predictive application of water column plume information to guide seafloor mineral exploration.

Jan 1, 2002

By AIME AIME

TRANSFER to the Bureau of Mines of the responsibility for conservation and production of helium, and announcement that a proposal has been made to the President for commercial operation of the Los Angeles has attracted new attention to the helium program of the Government. The matter is one in which mining engineers, and the mining industry in general, have a peculiar interest. Helium is a byproduct of the petroleum and natural gas industry. It is found in certain of the natural gases which have themselves been discovered, in the main, in the search for oil. If it is to be produced on a large scale, the conservation and development of the fields will necessarily be done by the men of the oil and gas industry. There is no known or expected source of supply of quantities of commercial importance save in the natural gas fields. Not all gas wells supply helium and none of them supply it in important percentages. If it were necessary to prospect a field, develop it, lay pipe lines and build production plants for the helium alone, the cost would be prohibitive. On that basis helium would necessarily be restricted to essential war uses, where cost is subordinate to need. As a byproduct of the natural gas in certain, at least, of the fields in the United States there is distinct reason for anticipating that it may be produced in amounts and at a cost that will permit its regular use in commercial airships.

Jan 1, 1925

By A. C. Johnson

The Bureau of Mines explored the Three Kids deposit in 1941 as part of a strategic minerals program. Earlier mining and exploration had established the presence of a substantial tonnage of medium-grade wad ore, and drilling and sampling by the Bureau of Mines, in collaboration with the Federal Geological Survey, indicated an additional tonnage such that development and exploitation became more clearly feasible. Private interests, with Government support, undertook to produce metallurgical-grade manganese. The present paper describes the Bureau of Mines exploration and subsequent development. Manganese in the Three Kids area is found in one of the lower members of the Muddy Creek formation in a bed of fine sandstone and silt, which outcrops around the north edge of the River Mountains and generally dips 20° to 40° away from the hills. There is considerable variation in the thickness and grade of the ore. The ore is light weight, having a density of 1.2 to 2.

Jan 1, 1956