Search Documents

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By A. J. Davidson

A Cu-conducting solid electrolyte was used to develop the sensor. Instead of measuring the potential across the electrolyte from the reference material to the Cu-containing phase, a potential was applied and the stable current measured. This gave reasonable readings for copper-tin alloys, which agreed with the theoretical calculations, but was less satisfactory in the case of mattes because the surface area of electrolyte presented to the matte phase varied from sensor to sensor. To overcome this problem the potential was applied, the current was measured and then reversed and remeasured and the ratio of the currents was calculated. The current ratio is shown to be independent of the resistance of the electrolyte and the surface area of the electrolyte offered to the melt, but strongly dependent on the activity of the copper

Jun 21, 1905

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

By Margaret Anne Stephenson

While the concepts of Aboriginal title share a similar jurisprudence in both Australia and Canada resource development regimes on Aboriginal title lands differ significantly. In Australia, the process is the right to negotiate with mining proponents. In Canada, the process is the duty to consult with government regarding mining projects. This paper compares and assesses the processes for ?consultation and negotiation? with Indigenous peoples when development actions (particularly in the context of mining resource development) impact Indigenous property rights and how agreement making can be progressed. This paper will question whether the resource development processes afford Indigenous people?s property rights full respect when mining developments on Indigenous lands are proposed.

Aug 1, 2013

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By P. J. Rowsell, M. D. Waller

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The applications of artificial intelligence systems in the upstream petroleum industry are reviewed. Particular emphasis is placed on current and potential applications in drilling engineering. Several recent advances in drilling technology have led to a large increase in the quality and volume of data available. This combined with the escalating cost, particularly of off-shore operations, is testing the traditional reliance on the skill and judgement of rig operators. AI systems offer enormous scope in enhancing and aiding the performance of these operations

Apr 1, 1994

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

By F. H. Willcox

This publication is the third of a series of reports on hazards and the prevention of accidents at blast-furnace plants that is being published by the Bureau of Mines, Technical Paper 106a being the first and Technical Paper 136b the second of the series. This bulletin, which is arranged in three parts, treats of the causes and prevention of blast-furnace breakouts, explosions, and slips. The first part discusses blast-furnace breakouts, the hazards therefrom, causes, and features of furnace design and methods of operation that tend to prevent breakouts or lessen their number, and points out safety measures to be adopted. The second part takes up the theory and causes of gas explosions at blast-furnace plants and reviews the better methods in use for handling gas. The third part analyzes the causes of hanging and scaffolding in blast furnaces, with the resulting slips that frequently cause injury to the plant and danger to the workmen, describes features of construction and furnace design and methods of operation employed to prevent hanging and slipping, and suggests precautions and safeguards.

Jan 1, 1917

By H. M. Lawrence

"Florida, the State that supplied 82 per cent of the phosphate rock sold in the United. States in 19284, has two producing areas - the hard-rock and the land pebble districts. Production of the hard-rock field, decreasing importance in recent years, is now confined to mines near Dunnellon, in Marion and. Citrus Counties. The land-pebble district, with a production of almost 80 per coat of the nation's requirements, is located, in Polk and Hillsborough Counties. In the land-pebble area the phosphate deposits - probably Pliocene in age, derived by marine action from underlying, older, phosphate-bearing formations - consist of beds of phosphate matrix, covered by practically barren sands and clays. The overburden, ranging in thickness up to 45 feet, is removed by hydraulic methods or by drag-line excavators. The matrix, ordinarily less than 25 feet in thickness, is mined by hydraulicking and is pumped to adjacent washing plants for beneficiation. The dried product of the washing plants is the Florida pebble rock that is sold in foreign as well as domestic markets.The beneficiation of phosphate ores in the land-pebble district of Florida has been largely limited in the past to the recovery of the coarser pebbles. By washing and screening the crude matrix a separation is effected at about 20 mesh (0.033 inch). The coarser material is the phosphate-rock product of the plant and the finer material is discarded. The amenability of the washer- rejects to treatment by other processes is being investigated. Of methods that may have some application to the treatment of the low-grade phosphatic sands that comprise the greater portion of the washer-rejects, gravity concentration has received some study.Laboratory experiments to determine the amenability of phosphate sands to gravity methods of concentration were first performed in October, 1927. Later, in the winter of 1928-1929, a further series of teats was made,. In these later tests phosphatic sands were concentrated by hydraulic classification, and. also by hydraulic classification followed by tabling. In these experiments concentrates with an analysis above the minimum grade of commercial phosphate rock (66 per cent bone phosphate of lime - B.P.L.) obtained. The recovery of the phosphate varied but was promising enough to warrant further study. A more comprehensive investigation was therefore outlined. This paper presents the results obtained from an investigation, of classification and tabling of phosphatic sands recently completed by the United States Bureau of Mines Su cooperation with certain Florida phosphate companies, the Missouri School of Mines and Metallurgy, and the University of Alabama."

Jul 1, 1930

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but attention in order that others may be rather more fully dealt with; for instance, referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c. The plans of the tin-streaming shed, sluice and feed race, and overburden tail-race represent types of the most modern design.GEOLOGY. The principal alluvial dcposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma River or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank...

Jan 1, 1910

Although the pattern of metamorphic zones south of the Thackaringa-Pinnacles Fault is much obscured by polymetamorphism, displacement of the orthopyroxene isograd by the fault agrees with the displacement of a horizon of "banded aplite" mapped by Andrews (1922). A dextral transcurrent component of 20,000 ft is indicated.INTRODUCTIONThe east-west Thackaringa-Pinnacles Fault (Andrews, 1922; King and Thomson, 1953), one of the major geological structures in the Broken Hill district, New South Wales, cuts across the general north-easterly strike of outcrops and fold structures of the Willyama Complex. The degree of shearing and recrystallization in its unusually wide crush zone and the manner in which adjacent rock units and structures have been dragged into conformity with its strike denote considerable movement on the fault. Information concerning the nature of this movement is of critical importance in the search for possible continuations or repetitions of lead-zinc mineralization south-west of Broken Hill.A transcurrent movement of 20,000 ft, with the southern block moving west, was estimated by Andrews (1922), who correlated prominent outcrops of "banded aplite" at The Pinnacles (north of the fault) and Big Hill (south of the fault). Displacement of this order, however, does not seem sufficient to explain the extent and character of the fault zone. Recent chemical and petrological studies of the banded aplites at The Pinnacles and Big Hill by Vernon (19B1) confirmed their similarity, but indicated an origin by metasomatic replacement of pre-existing folded and metamorphosed rocks. This raises the possibility that some...

Jan 1, 1965

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

A hard lump char containing only 4 to 5 per cent ash, 0·25-0·30 per cent sulphur and a trace of phosphorus has been produced from Latrobe Valley brown coal by slow drying and carbonization of ordinary industrial briquettes at temperatures between 7000 C and 14000 C. The briquette char can be made with a variety of reactivities by varying the maximum temperature of carbonization; the higher the temperature, the lower the reactivity. The strength of the fuel compares favourably with metallurgical coke made from black coal, though it may not be quite so resistant to abrasion. Experiments in a small experimental cupola indicate that it will make a satisfactory fuel for use in iron foundries. It may also find extensive application as a smokeless fuel in other branches of industry and in household heating appliances.INTRODUCTIONVictoria, like South Australia and Western Australia, is apparently without 'significant deposits of black coal of coking quality but there are huge reserves of brown coal of high moisture content (60-66 per cent) in the Latrobe Valley (well over 20,000 million tons have been proved) and there are other important deposits in the south central portion of the State (Herman, 1952).For three decades Victorian industries, including a few metallurgical firms, have been using the briquettes made at the Yallourn factory of the State Electricity Commission of Victoria (S.E.C.). These briquettes, having a moisture content of about 15 per cent and a calorific value of approximately 9,500 B.T.U. per pound, are satisfactory for certain grate-type furnaces but they are not suitable for use in cupolas of other shaft furnaces because they disintegrate badly on rapid heating.

Jan 1, 1956

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931