Search Documents

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

Most mines in the Bundamba, North Ipswich, and Rosewood districts of the West Moreton coalfield of south eastern Queensland have installed washing plants during the last five years. Many problems were encountered in their installation, including the small size of washing plant required in many cases, the economical minimum ash content under present and future market requirements, production from a one-product washbox of large and small coal of quality to satisfy both markets, measures to avoid adding unnecessary moisture to the washed slack coals, and excessive middlings in some coals or soft clay in others.INTRODUCTIONIt was fortunate for Brisbane, which was to become the capital of a new State, Queensland, in 1859, and grow into a city of over half a million people by the time of its centenary, that coal was found in abundance almost on its doorstep near Ipswich, the first mine being opened at Redbank in 1843. This was followed by the opening of many more mines in that district and, some 40 years later, in the nearby Rosewood district where high-volatile gas coal was produced (Fig. 1). These discoveries ensured a supply of reasonably priced coal (currently about 85/- per ton delivered) in Brisbane, but the quality is inferior to that of other coals mined in Queensland beyond economic range of Brisbane.Various factors led to an increase in the average ash content of the West Moreton coals during and after the war. Between 1940 and 1952 the gasworks coals rose in average ash from 13 8 per cent to 23·9 per cent and the powerhouse coals from 17·1 per cent to 27·1 per cent. This drift was arrested by the installation of 28 screening and picking plants from 1952 onward, but it became obvious that mechanical cleaning of the coals was essential due to the competitive market for coal and the worsening quality of reserves.

Jan 1, 1963

By B. R. Broekman, K. J. R. Ford

Over the last decade significant development and use has been made of a simulation model that describes the HCFeMn smelting operations in Assmang Ltd. This spreadsheet based, semi-empirical, predictive model is derived from data from the submerged arc furnaces at Assmang?s Cato Ridge, KwaZulu-Natal smelter site. Departures from the empirical base case mass balance due to changes in the ores, reductant feeds and operating parameters are accounted for by use of fundamental relationships and heuristic type ratios which are applied in an iterative manner in the model. The model performs a sequential set of calculations to iteratively converge on a fully consistent mass and energy balance solution, which predicts Mn alloy and slag output masses and compositions for a given set of feeds. 440 MWh per operating day is used as the basis of energy input. The paper describes the key model components, assumptions made and calculation approach. Added to the mass and energy balance is a cost and revenue balance, which allows prediction of the economic performance for each simulation. Substantial use of the model has been made in simulating the performance of the current Assmang HCFeMn furnaces for both smelter investigations and future production planning. The model has also been a valuable tool in the strategic analysis of the use of future Mn ores and has formed the vital link between mine ore grades (metal and slag elements) and the expected alloy output, grade and profitability. Additionally, the model has been used in benchmarking exercises to predict other Mn smelting operations with remarkable accuracy. The paper highlights some aspects of the approaches taken in using the model to benchmark Assmang?s own furnace performance and cost competitiveness with other producers. For Assmang the development and application of this modelling technology has led to transformation in understanding of the Assmang HCFeMn furnace operations and increased awareness of the potential of its Mn ore bodies.

Jan 1, 2004

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By Susan M. White

Increased coal production, wider use of indiscriminate mining techniques, improved cleaning methods, and greater emphasis on clean fuels is increasing the rate at which wastes accumulate Over the next several years, Colorado Plateau underground coal production is predicted to increase. Currently, mine refuse is deposited in canyons or lowland areas near mines. This study presents information on the nature of coal refuse and disposal practices on the Colorado Plateau. Samples were collected and analyzed to provide information to help formulate alternative methods for reclaiming refuse piles. The analyses were based on determining the capability of unmodified refuse to provide a suitable medium for plant growth. Local topsoils which would be used in reclamation were used as standards. Potential environmental hazards were assessed also. A general cost analysis was done for both surface and underground disposal and the advantages and disadvantages of each were assessed. Several problems were identified which, if solved, would increase the effectiveness of state regulatory programs.

Jan 1, 1982

By Greg Ford

Each year, companies spend millions of dollars on safety training and on safe equipment, money that is generally well spent. Despite that, we still make mistakes. What happens if the mistakes are made not because of inadequate training, but because we are hard-wired to act in a certain way? If you read any of the ?Because of Human Error? text boxes in this document, situations like these may look familiar in your own workplace. ?The issues of risk, health, safety and the environment are getting more attention now than ever before, at all levels of the organization,? said Calvin Price, vice president of Global Health and Safety at LNC-Lavalin Inc., a company with 21,000 workers worldwide. Most would agree with Price that attention to safety is increasing because responsible companies care about their workers and the workers? colleagues, families and communities. However, cynics might say that the safety spotlight is powered by the corporate bottom line. Direct costs created by workplace injuries total $51.8 billion annually and include workers? compensation payments, medical expenses, civil liability damages and litigation expenses. This sum represents a staggering one quarter of each dollar of pretax corporate profits. Indirect costs may run as much as 20 times the direct costs of on-the-job accidents and illnesses. Examples of indirect costs include training replacement employees, investigating the accident and implementing corrective measures, lost productivity, repairing damaged equipment and property, and costs associated with lower employee morale and absenteeism. What?s interesting is that up to 90 percent of incidents are due to human error, not faulty equipment or other factors.

Aug 1, 2013

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

By F. Schlosser

The extension of Montparnasse Station in Paris required the construction of supports of very high unit capacity to support a particularly rigid super-structure. The majority of the site is characterized by the existence of old limestone quarries at a depth of approximately 20 metres. These workings have been backfilled in some places, have collapsed in some places and have given rise to local subsidences in the marne layers above them. This paper addresses the steps taken by the group of companies and their consultants to evaluate the equivalent stiffnesses of the supports necessary for the design of the superstructure, and gives details of the construction techniques chosen by the foundations specialist to adapt to the particular conditions encountered on this site.

Jan 1, 1989

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Martin Herrenknecht

The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge to provide efficient traffic infrastructure, such as a modern public transportation system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are also essential. Additionally, supra-regional transportation routes such as long distance water diversion schemes are the challenges for the future. All these projects are as demanding as they are characterized by a tight time schedule.

Jan 1, 2010

By Dean Workman

Long extensible conveyor systems are an important option for efficient tunnel excavation where intermediate access is impractical. The conveyor system designed for the Pula Subbaiah Veligonda Tunnel #2 in Andhra Pradesh, India will eventually extend to 19.35km. The Ø10.0m water diversion tunnel will be excavated under India?s largest tiger sanctuary using a Robbins Double Shield TBM. Once extended, the conveyor will be one of the longest single-flight systems ever installed in India, and is expected to offer increased system availability over comparable systems using muck cars. This paper will examine the engineering challenges of long-flight extensible conveyor systems in the areas of belt selection, component design, and equipment location in confined assembly and launch areas

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By Don Phelps, Dean Brox, Peter Procter, Andy Saltis, Tom Morrison, Jeff Pringle

The Greater Vancouver Water District is currently constructing the Seymour-Capilano Water Filtration Project to enhance the quality of drinking water in the Vancouver metropolitan area. The Seymour-Capilano Water Filtration Project comprises the 1,800 million litres per day Seymour-Capilano Filtration Plant, the 1,080million litres per day Capilano Pumping Station, twin tunnels with associated shafts, and the Capilano Energy Recovery Facility. The twin tunnels will convey raw water under pressure from the Capilano Reservoir to the Seymour Filtration Plant and return treated (filtered) water for distribution. The Twin Tunnels component of the project comprises twin, 3.7 m diameter, 7.2 km TBM bored tunnels, the 180 m deep Seymour Shaft as the main launch shaft, and two 4 m diameter, 268 m deep raise bore exit shafts at Capilano. The Twin Tunnels have been planned as predominantly unlined tunnels sited at depth entirely within granitic bedrock and cross under two major buried glacial valleys of breadths in excess of 1500 metres that are filled with glacial sediments to depths up to 200 metres. The maximum overburden along the tunnel alignment is approximately 400 metres. Comprehensive site investigations and studies were completed during the detailed design stage of the project. The construction of the twin tunnels started in the fall of 2004 and is planned to be completed by mid-2008.

Jan 1, 2005

Ensuring the success of a major resource development project, whether in the Gippsland Basin or elsewhere, is typically both a complex and costly process. It is therefore imperative from the point of view of the proponents of such a project - and in particular the financiers - that everything possible be done to minimise administrative confusion and delay in the establishment phase of the project, and to put systems in place which enable the project to run smoothly and efficiently in the later stages of its development and operation. An essential element in this process is ensuring that the project management is able to come to terms with and deal effectively with the relevant planning and environmental laws.

Jan 1, 1992

By S. Peterson, E. C. Westman, P. L. Swanson

Coal bumps are brittle, violent failures associated with high stresses and competent host strata. To study bump mechanisms, conditions in the vicinity of a deep longwall mining face in bump-prone strata were monitored using three discrete systems. First, a microseismic monitoring network recorded mining-induced seismic events throughout the mine and surrounding strata. Second, pressure variations and distributions on the longwall shield legs across the face were recorded. Last, tomography surveys imaged seismic transmission properties ahead of the face. Results from the three systems were correlated in an effort to increase understanding of mining-induced stress redistribution and bump potential. An initial, one-week study showed that the correlation between averaged tomogram values and seismically active areas had a coefficient of correlation (R) of 0.89. Further results of these studies demonstrate that the tomography system is capable of imaging heavy shield-leg loading and bump-prone conditions prior to them disrupting the face operations.

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used 1n this report are divided into two components for individual analysis--(1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations. The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By Kimiz Dalkir

Some things to keep in mind? ! What is your role in knowledge management? ! What knowledge-related challenges are you facing today? ! How does important knowledge get shared in your organization? ! Can you name factors that enable/block innovation and organizational learning in your work context? A brief history of KM? ! Top-down / imposed ! Rigid / bureaucratic ! Slow deployments ! Expensive ! Unpopular: empty libraries, info-junkyards, low adoption rates ! Problems measuring success ! The result: traditional KM is not the answer

May 1, 2003

By L Bartsch, M Kelahan, E Wingate, J-S David

The use of column flotation cells for recovery of phosphate is becoming more common practice in certain parts of the world (Brazil, Russia) where igneous phosphate ores are processed. Igneous phosphates are generally finer grained (< 200µm) than some of the traditional sedimentary phosphates (<400µm). Australian phosphate from the Georgina basin is sedimentary, but has a much finer grain size (typically < 106µm) than similar deposits in North Africa and the USA.In 2013, Arianne Phosphate completed a bankable feasibility study for the development of their igneous phosphate deposit at the Lac a Paul site in Quebec. Initially, lab test work and bench scale piloting indicated that using traditional mechanical flotation would be able to produce adequate concentrate grade and an economic level of recovery, but would necessitate the installation of a complex and operationally challenging flotation circuit. Later pilot plant testing using column cells resulted in a significant reduction in process complexity and facilitated the processing of the -20µm ore fraction which resulted in a 10% increase in P2O5 recovery and a 5% increase in concentrate grade %P2O5.Flotation column testing achieved a concentrate grade of 38.6% P2O5 at a P2O5 recovery of 90%. Using a mechanical flotation cell circuit, the concentrate grade was 36.4% P2O5 with a P2O5 recovery of only 78.8%. A noticeable feature of the testing was the simplicity of the column flotation circuit configuration (Rougher + 2 stages of cleaning + Cleaner Scavenger) compared to the mechanical flotation cell circuit (Rougher + Scavenger + 3 stages of cleaning).The financial benefit for this case study was estimated using a sales price of US$ 195/t FOB for a 38.6% P2O5 product, and an assumed cost of production of US$ 95/t, the netback price is calculated at US$100/t. For a daily milling rate of 55,000t/d, the improved flotation performance provides additional concentrate production of 1,203t/d. Using the netback price calculated above, this calculates to additional gross profit of US$ 120,260/d.Annualised, this equals US$ 40.7 million in additional revenue for a similar or reduced CAPEX.The use of column flotation on fine grained phosphate ore types often requires fine grinding and desliming to liberate the phosphate value, such as the Australian sedimentary phosphate ores. This may enable the development of deposits previously regarded as uneconomic.This paper discusses the potential benefits available to operators, and developers of new projects, for the use of column flotation cells in their metallurgical circuits as assessed by an engineering company.CITATION:Wingate, E, Kelahan, M, David, J-S and Bartsch, L, 2015. Does it make cent$ to use flotation columns for phosphate beneficiation?, in Proceedings MetPlant 2015, pp 353–365 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015