Search Documents

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

Let’s start off with your assessment of the mining industry. Today, the status of the mining industry is stronger than it has been over the previous few years. While mining continues to be a major part of the world’s economic foundation, the industry is gaining strength due to rebounding metals and minerals prices. And now, with these rising prices and the changes the industry instituted during the years when mining-related commodities were selling at low prices, our stronger, more productive and internationally competitive industry should flourish. Mining remains an essential business and the industry is far ahead of the game when it comes to the trend of globalization as a key to sustained growth. Also, the industry continues to realize increased productivity through technological innovations. And an increasing number of countries are moving towards capitalism, which opens doors for exploration and mining within their borders. After looking at all of these factors, I believe that the mining industry will only continue to gain momentum in the future.

Jan 1, 2004

The sulphide ores of the principal lodes of the Boulder Mines are mainly composed of a schistose guess with a varying proportion of silica and lime, containing tellurides of gold, silver and mercury, associated with iron pyrites. It is a great difficultyto obtain pure and homogeneous samples of the tellurides for analysis, and from a number of tests made with excellent specimens it was found hardly possible to procure two to agree in analysis, the precious metals being found to be combinedwith tellurium in most varying proportions indeed, a close inspection of a partially crushed specimen will reveal, even to the naked eye, the various shades of colour characteristic...

Jan 1, 1901

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By Joseph J. Feiler

Historical mining operations in Colorado and other western states have resulted in thousands of remnant mine openings. Many are sources of metals loading and acid water generation in surface and ground waters. It is estimated that more than 965 km (600 miles) of streams in Colorado have been impacted by past mining activities. The Animas River watershed in southwestern Colorado is one of the most heavily affected areas in the state. Abandoned mine features pose significant safety hazards to those who enter them. These hazards can include bad air, unstable rock or falls into open shafts, stopes and winzes. Backcountry skiers and snowmobile enthusiasts are particularly vulnerable to falls into snow covered mine openings.

Jan 1, 2006

By Jia-Shyan Shiau, Chung-Ken Ho

An uneven gas distribution through the burden layers inside a blast furnace (BF) results in abnormal gas resistance or pressure changes. Rapid variations in the abnormal gas resistance will lead to the occurrence of channeling. A visualization technology mainly made of pressure distribution was developed to predict BF channeling phenomena in this study. The real-time data of BF shaft pressure was used to create a 3D visual model by neural network algorithms and 3D real-time BF pressure changes were observed. The root mean square deviation (RMSD) of the BF shaft pressure was used as an index to set up the predicting criteria of channeling occurrence with the opening of BF Annular Gap Element (AGE), and a predicting system based on the criteria was built. The two criteria for the channeling alarm are the RMSD of the BF shaft pressure (> 0.15 kg/cm2 ) at the upper two levels, and the AGE opening being greater than 60%. This system has been installed in the China Steel Corporation (CSC) BFs, and the test results showed that a prediction can be obtained 8 to 16 min ahead of channeling allowing sufficient time for the operator to adjust the BF operation in order to avoid the occurrence of channeling.

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts of Mineral County, Nev., made during the month of June and the first 10 days in October 1936.3/ During the field work virtually all the mining districts in the county were visited and many data were obtained relative to active and inactive properties. The report covers the location of the various mining districts, nature of deposits, ownership, information on past and current activity, data on economic conditions, and general information likely to be useful to operators and investors and others interested in mining. The geology of the deposits is discussed only in a general way. For nearly three-quarters of a century mining tin Mineral County has been the principal if not the only industry of importance. At times it has reached a very low ebb, and at other times it has been attended by the wild excitement that usually accompanies valuable discoveries of precious metals.

Jan 1, 1937

By Bruce Richardson

A contractor-manufactured 4.75m (15'-7") diameter EPB shield excavated a 115m (375 ft) long tunnel under the San Antonio River as part of the Salado Creek to Dos Rios Pipeline Interconnect Project in San Antonio, Texas. Lignite, limestone concretions, and sandstone in the face of the tunnel required the use of disc cutters. Less than 7.6m (25 ft) of sand and gravel hydraulically connected the top of the tunnel to the channel of the river. Fully lagged steel ribs with filter fabric were used for initial ground support and water control. This and other contractor manufactured TBMs in the 1.2 to 4.75m (4 to 16 ft) range are presented with descriptions of the jobsites, equipment, performances, and problems.

Jan 1, 2008

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

By C. Bazin

Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action to correct the problem. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality leading to a less efficient grinding operation. A dynamic simulator is used to assess rules for the diagnosis of hydrocyclone faults from the trends produced by sensors.

Jan 1, 2009

By Alvin Kaufman

Increased exploration in Alaska has resulted in many requests to the Bureau of Mines for facts about the mineral resources and mining conditions in the Territory. This report presents information about the minerals of Southeastern Alaska and the factors that affect development of a mining industry in that area. Southeastern Alaska is a narrow coastal strip of rugged mountains and many islands. The climate is mild, with an average annual temperature of 40° and heavy rainfall. Geologically, the region is favorable for deposition of ore; geographic-ally, it is difficult to prospect and to develop, except along areas immediately adjacent to the coastline.

Jan 1, 1958

A simple process for making filter aids from coal by controlled carbonization at 800-1200·C is described.Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization.Product yields depend upon the composition of the parent coal but are always less than the sum of the ash and fixed carbon values determined by the proximate analysis. The product yield also depends on the air-to-coal ratio, which affects the amount of coal substance burned and the temperature attained. Particle residence time and reactor temperature affect the degree of devolatilization of the product and hence its wettability. The filtration behaviour of carbonaceous filter aids is greatly influenced by the size distribution, shape and physical properties of the particles-parameters which are largely determined by fue type and particle sizing of the coal used.Carbonaceous filter aids are distinctly different from other types commonly used and extensive industrial applications are anticipated in a wide range of industries ranging from food to mineral processing.

Jan 1, 1970

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By John D. Campbell

"IS YOUR MANAGEMENT CONTROLLOOP FUNCTIONINGMineral processors make use of hundreds of control circuits in their mills, process plants, smelters and refineries, to optimize throughput and recovery and minimize cost. This afternoon, I would like to discuss what is probably the weakest circuit in any mineral processing operation - the management control loop.In their recent book ""The Winning Streak"", Goldsmith and Clutter describe extensive research on unsuccessful companies. They conclude that ineffective control, which does not immediately identify the problems, is one of the main failings of unsuccessful companies.We will look at the three key components of control which, from the manager's point of view, ensure that the loop is complete. These three are:• measuring what's happening,• assessing its significance, Rnd• altering performance.If we compare management control to process control as shown in this first figure, ""We see that parameter sensing by the analyzer in a process circuit is analogous to performance monitoring by management in a responsibility centre. The analyzer senses temperature, pressure, flow, weight or some surrogate indicator such as colour to indicate ion concentration. For manage1nent, the performance to rnonitor is dependent upon the objectives of the responsibility centre, and the key factors which affect these objectives."

Jan 1, 1985

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

The commercial development of the shallow (2200 ft2 400 ft) Windalia sand reservoir at Barrow Island provided the opportunity to conduct an intensive drilling programme using equipment and techniques designed for optimum performance.During the initial exploratory and reservoir delineation phase, 12 specific Windalia test wells were drilled using drilling equipment with an optimum depth range of 6QOO ft - 8000 ft and a 9 5/8 in by 7 in. casing programme was employed. The average time from commencement of move-in to rig release exclusive of coring for five representative wells was 187 hr during this phase.Development drilling commenced December 1966 with one rig, with the second in operation January 1967.As of January 1 1968, 168 development wells had been completed. The two rigs employed are drive-in units equipped with a telescoping .gelf raising doubles mast.Optimum depth range with 4 1/2 in. drill pipe is 2500-4000 ft. Casing programme is 8 5/8 in. by 5 1/2 in. Efficient performance was achieved immediately. The average time from commencement of move-in to rig release for 15 wells drilled early in the development programme was 99 hr.By application of experience and further modification of techniques, performance was improved to an average time of 72 hr per well for 15 wells recently completed.The major drilling problem on Barrow Island is surface hole drilling due to the very hard surface limestone combined with complete loss of circulation at sea level.In this operation, significant improvements have been effected. During the exploratory phase drilling, 12 1/4 in hole to set 9 5/8 in. casing, average penetration rate was 23 ft/hr. At the commencement of the development programme penetration rate, drilling 10 5/8 in. hole to set 8 5/8 in. casing, was 28 ft/hr for the 15 early wells considered, improving to 55 ft/hr for the 15 recent wells considered.This programme is a team effort and much credit must be given to the enthusiastic co-operation of the two drilling contractors.The current field record is 2 days 4 hr with a 4 1/2 hr move including the drilling of mousehole and rathole.

Jan 1, 1968

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By Keith Merriam, Jim McDonnell, Peter Radziszewski, Rob Rotzinger, Ian DeHart

"Taseko Mines Limited Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.In the second staged development project, a VTM-1250-WB regrind mill was selected to replace the existing conventional ball regrind mill to achieve a target grind size of 80 % passing 45 µm. In the third staged development project, a second VTM-1250 regrind mill was selected for installation in Concentrator #2, to match the existing Concentrator #1 Vertimill. This resulted in approximately 25% spare regrind capacity in the Concentrator #2 design, complete spare parts interchangeability and potential future expansion capacity to 50,000 t/d with no circuit upgrades.In this context, a study was initiated to assess not only the performance of a Vertimill grinding circuit processing a copper concentrate to a particle size of 80% passing 17 µm but also to provide Taseko’s New Prosperity project specific design information for grinding to particle sizes below 80 % passing 25 µm.The objective of the work described in this presentation was to explore Vertimill ultrafine (sub 100 µm) grinding test methodologies at both the lab and pilot scales, compare the scale-up data with operational data from the VTM1250 at Gibraltar Mines and subsequently apply this information to particle sizes down to 80% passing 17 µm. The presentation will describe the results obtained preceded by a description of the Gibraltar regrind circuit historical operation and operational performance as well as a description of the Vertimill technology.INTRODUCTIONTaseko Mines Limited is a mining company headquartered in Vancouver, British Columbia, Canada. In addition to mining development projects for copper, copper-gold, gold, and niobium properties, Taseko Mines is seventy-five percent owner and the operator of the Gibraltar Mine near Williams Lake , British Columbia. Taseko Mines Limited’s Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.Metso is a leading process performance provider, with customers in the mining, oil and gas, and aggregates industries. It has corporate headquarters in Helsinki Finland, offices in 50 countries and manufacturing facilities on five continents. Amongst other types of equipment and services, Metso designs and manufactures VERTIMILL® (VTM) Grinding Mills."

Jan 1, 2015