Search Documents

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013

By C. J. Newman

The new Kennecott Utah Copper smelter, started in 1995, was designed to be the cleanest smelter environmentally in the world. The plant is operating at production rates above the original design capacity. Copper concentrate is smelted in an Outokumpu flash smelting furnace. Matte is granulated and processed using Kennecott-Outokumpu flash converting. Copper anodes are processed in a modernized copper refinery using the Kidd Process while anode slimes are processed for precious metals recovery using a unique hydro-metallurgical process. To allow the production of high quality cathode, using modem smelting and converting technology to minimize emissions, impurity control had to be carefully addressed. All process bleed streams from the smelter and refinery are treated in a hydro-metallurgical plant to fix impurities in a stable form, allow for the rejection of impurities as required and recover valuable metals. Special technology was developed for the copper refinery to ensure production of high quality cathode from anodes containing high levels of impurities. The smelter routinely achieves a sulfur capture in excess of 99.9% which is equal to less than 2 kg of SO2 per tonne of copper produced. This paper describes the design of the smelter and refinery and includes recent production and emission data and modifications carried out to allow operation at above the original design rates. It emphasizes the unique features required to achieve environmental and quality goals and compares environmental performance data to that published on other smelting operations. The processing of intermediate streams, the management of recycled materials and the impurity control strategy will be covered in detail.

Jan 1, 1999

By Eric J. Grimsey

Nickel smelting and converting can be viewed as processes in which iron is either partitioned or transported between matte and slag. Metal recovery depends on the mass of iron transported to slag, the thermodynamic environment in which the transport is made, and the extent to which the slag, once formed, is left in contact with the matte. The importance of these effects is discussed with reference to a new equation which describes metal recovery in terms of a mass balance and a thermodynamically related parameter which is easily measured in practice.

Jan 1, 1993

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By F. J. Tavera

A study on the electro kinetics of lead carbonate, silica, and alumina, in aqueous media was carried out at different pH values. The behavior of potential was determined for these species in the pH range between 3 and 12. Homocoagulation of lead carbonate in aqueous media is analyzed at its isoelectrical point. Lead carbonate heterocoagulation is analyzed with silica, alumina, and silica ? alumina mixtures at low pH values. The experimental results are considered for their possible application to treat residual water polluted with lead.

Jan 1, 2006

By J. B. Vander Sande, I. G. Solórzano, B. S. You, P. M. Jardim, W. W. Park

"Alloys with six different compositions in the system Mg-Ca-Zn were produced by melt spinning. The aging behavior of alloys was investigated by measuring the changes in microhardness after isochronal aging and the microstructure was analyzed by means of transmission electron microscopy (TEM), energy dispersive X-ray spectrometry (EDS), scanning transmission electron microscopy (STEM) and scanning electron microscopy (SEM). All six compositions in the as-solidified condition show a difference in microstructure between the wheel contact side (zone A) and the free surface side (zone B) as a result of the differences in the solidification rate across the ribbons. One of the alloys (Mg-l.5wt%Ca-6wt%Zn) was chosen to be more deeply investigated in this work as it exhibited grain boundary films and an age hardening behavior was produced in that alloy.IntroductionMagnesium is the lightest of all the commonly used metals, and very attractive for applications in transportation. It also has a number of other desirable features, including good ductility, better damping characteristics than aluminum, and excellent castability. However, there are some negative features, such as high reactivity in the molten state, inferior fatigue and creep resistance as compared to aluminum, poor corrosion resistance and high production cost.In recent years there has been a significant increase in magnesium use as a structural material. These structural applications include aerospace, automotive and nuclear industries as well as appliances and sporting goods (1 ). According to reports on Mg-Zn alloys, the addition of Zn (2) in magnesium increased strength. Also, since the maximum solubility of Zn in magnesium is 6.2wt%, a considerable amount of Zn can be retained in solid solution in magnesium alloys by rapid solidification. In addition, Ca is known (3) to be one of the most potent alloying elements for refining the microstructure and precipitates in magnesium alloys, and also to improve mechanical strength and corrosion resistance."

Jan 1, 2000

By Jitka Jandová

In this study, hydrometallurgical processing of waste ZnO flue dust arising during zinc removal from galvanized low-alloy steel sheets was investigated on a laboratory-scale to obtain electrolytic zinc. The flue dust was separated from flue gases, generated during heating waste galvanized steel sheets in an electric furnace under air atmosphere at temperatures of about 1000oC. The dust, comprising tetragonal ZnO and insignificant amounts of SiO2, was contaminated by Fe, Mn, Pb, Al, Mg, Pb, Cu and Ca. The dust was leached in 0.5 and 1.0M H2SO4 and/or in 20 and 30% NaOH at different temperatures and different liquid-to-solid ratios to determine the optimum conditions leading to the highest possible selectivity of leaching and efficiency of Zn extraction in minimum time. The subsequent electrowinning process was performed with refined zinc sulphate leach liquors and/or with untreated zinc caustic solutions. Zinc sulphate leach liquors were purified using a combination of a hydrolytic pH-controlled precipitation, cementation and carbon refining. Effects of operational variables on Zn electrowinning have been studied for both sulphate and caustic electrolytes. The conventional plate-plate electrowinning cell has been explored in this study. Comparison of results obtained for both zinc electrowinning from acid sulphate and alkaline solutions is presented contribution.

Jan 1, 2003

By Andrew L. Puwis

Methodologies were presented for computing the thermal gradient associated with single crystal solidification in macroscopic computer modeling. The. heat transfer, and solidification of a shaped investment casting model were simulated using properties from three different alloys. Following the simulation of solidification, the resultant thermal gradients (G) and rates of solidification (R) from representative points were extracted in various ways and compared: It was discovered that alloy properties have a strong influence on the computed thermal gradient and rate of solidification for the three methods investigated. Data also showed that the computed gradient for each model was very different depending on the temperature range used to compute these values.

Jan 1, 1994

By Gerardo H. Achurra

During the last years, the Caletones Smelter, like others copper smelters in the world, has evolved from the conventional, inefficient, pollutant and expensive technologies, to modern, environmental1y friendly and efficient ones. For this reason as wel1 as to improve its competitive position this Smelter shut down the reverberatory furnace, started up two big acid plants and has developed some pyrometal1urgical technologies. The main facilities of the Caletones Smelting and Converting Process, in the present and the future, are the Teniente Converters, the reactors with a high operational availability that have reached concentrate top process capacities near to 2,400 tpd. These reactors operate in most of Chilean smelters as well as in other smelters in the world such as in Zambia, Peru and Mexico. Since 2000, the Caletones Smelting and Converting Process, has been adapted in two Teniente Converters, four Slag Cleaning Furnaces and four Pierce Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers and two Oxygen Plants have allowed to reach concentrate smelting capacities and copper productions of 1,250 ktpy and 380 kftpy, respectively. Associated to El Teniente Division Expansion Plan, Caletones Smelter, in the first stage, will increase its capacity to 1,440 ktpy in 2004. In the long term, Caletones has different options, such as the processing of 1,600 to 2,000 ktpy of concentrate, producing anodes, white metal or a mixture of them. These options are connected with CODELCO's Smelters & Refineries Strategic Plan, including Mejillones Project. The main challenges of Caletones Smelter are associated to the development and the consolidation of the Continuous and Environmental Friendly Processes, automation and control of different processes and to the improvement of its leadership between other Copper Smelters in the world.

Jan 1, 2003

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By Cheng Pan, Xuewei Lv, Guibao Qiu, Chenguang Bai, Meilong Hu

"Physic-chemical properties of slag at high temperature play an important role in the pyrometallurgical process of production of ferronickel alloy. It determines the operation efficiency, metal recovery ratio, energy consumption and the distribution of elements like S and P between the slag and metals. In the present work, the effect of MgO content in the slag on melting features and viscosity of the slag was investigated. The MgO content in the SiO2-CaO-MgO-Al2O3 -FeO in the quinary slag system varied from 14.5% to 22.5%. The results shown that all slag samples begin to softening at the same temperature, the softening temperature, melting temperature, flowing temperature decrease with the increase of MgO content when the MgO content is in range of 14.5 and 20.5 pct mass, and when MgO content up to 22.5 percent, the temperatures increase sharply. Besides the inflection point temperature of viscosity-temperature curve increase with the increase of MgO when the MgO content is in range 16 and 22.5 pct mass.IntroductionNickel is very important to modern society, without it, we would not be able to share many things in our daily life, such as airplanes, computers and many stainless steel appliances in our homes and workplaces1.. It is the essential element of the stainless steel making, and about 65% of the nickel consumed in the world is used to make stainless steel2., so with the increase of stainless steel, the nickel production and demand has continued to increase3.Nickel is produced from two distinct ore types: nickel sulfide deposits and oxide nickel laterite deposits. The great majority of world’s known nickel resources are contained in laterite deposits3.. The laterite ores are normal classified into two groups: the high-iron laterite ore and high-magnesia laterite ore1. Typical composition of high-magnesia laterite ore is in the range 1-3%, and these ores are suitable for pyrometallurgical process to produce ferronickel4."

Jan 1, 2012

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008

By Na Wang, Chao Du, Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Niobium aluminides were directly synthesized by a sodiothermic reduction process of NbC15 - AlCb which was dispersed into LiCl - KCl - NaCl - CaCb melts. The melt supplied a homogenous reaction medium which was substantially beneficial to the co-reduction of Nb and Al to form niobium aluminides in situ. The reduction was performed at 500°C for 4 hours. The products were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). The corresponding results indicated that niobium aluminides powders were successfully synthesized.1. IntroductionNiobium aluminides have received considerable attention as high-temperature structural materials, due to their high melting points, relatively low density, high strength, excellent oxidation and creep resistance [1-4]. Figure 1 shows that there are three intermetallic compounds in the Nb - Al binary [5], which includes Nb3Al (A15 structure, Cr3Si type), Nb2Al (D8b structure, cr-CrFe type) and NbAb (D022 structure, TiAb type). These niobium aluminides have been used in turbine blades or in stationary gas turbines [6-8]. However, despite their attractive features, the ir applications are still limited by the long and costly fabrication process [9, 10].Niobium aluminides were industrially fabricated by the mechanically alloyed process [11-13]. Traditionally, niobium is extracted from Nb2O 5 or K2NbF7 by a metallothermic reduction process while aluminum is produced by the Hall-Heroult process of Ah03 electrolysis. Based on the extraction of Nb and Al, respectively, niobium aluminides is synthesized by a mechanical powder alloying process. The present process for making niobium aluminides requires a set of complicated equipment, has high production cost and time consuming [14, 15].The purpose of this work is to present the simple, economic and direct synthesis of niobium aluminides powders utilizing a sodiothermic reduction from NbC15 - Al Cb dispersed into molten salts."

Jan 1, 2011

By Sergio Sanchez-Segado, Yuan Zhang, Animesh Jha, Ahmad Fahmi Ruzaidi

Niobium and tantalum are considered critical materials because the increasing demand in the energy sector which is reliant on limited abundance of these two metals in minerals. Traditionally, niobium and tantalum mineralsare digested using hydrofluoric acid at moderate temperatures, producing oxy-fluorides which are separated by solvent extraction, involving the use ofhazardous chemicals. The increasing environmental pressures are forcing the industry to search for alternative low carbon processing methods. In this paper alkali roasting based separation and beneficiation, which is not well understood in the literature, is proposed, for which the kinetics and thermodynamic equilibria for the formation of sodium tantalate and niobate with sodium hydroxide are analyzedat the temperature range of 400ºC to 700ºC. The apparent activation energy of formation,changes from 31.0±0.8 to 22.3±1.2 kJ mol-1 and from 23.8±1.2 to110.2±12.8 kJ mol-1, for tantalate and niobate, respectively. The reaction mechanism is examined on the basis of the analysis of reaction products using X-ray powder diffraction (XRPD) and X-ray fluorescence (XRF).

Jan 1, 2015

By Stefan Mutz

In Germany the automobile recycling is regulated by law. Current legislation requires that by the year 2015, eighty five w.-t. % of the components from used cars ill be materially recycled. Whilst for 10 w.-t. % of the materials a thermal utilization is certified, there are still some concrete questions that remain unanswered regarding the usability of single fractions. The recent innovative approaches to the concepts of used cars dismantling do not alter the fact that the majority of the materials of used cars still have to pass over the shredder and the connected processing aggregates. The status of the so called SLF (Shredder light fraction) which is about 25 w.-t. % w.-t. in used cars, has not been satisfactorily clarified. Furthermore questions still remain regarding the separation of the NMSF (nonmagnetic metal shredder fraction) which has to be separated in the single metallic fractions like stainless tell, copper, brass, zinc, etc. Attempts of optimization can be found. This paper analyses some of the difficulties being encountered by the automobile recycling industry in Germany, before reviewing some of the innovative approaches that the industry has introduced. Finally the paper goes on to describe the potential of automatic picking. Examples of a series of tests, utilizing this technology, in which a variety of products from a range of shredders were isolated are described in detail. This new technology provides a range of applications to the automobile recycling industry.

Jan 1, 2002

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF's. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By Hiroyuki Matsuura

Treatment of electric arc furnace (EAF) dusts has become an important issue from the viewpoint of the environmental protection and recycling of variable resources because these dusts contain considerable amount of zinc and lead. A new recovery process of these metals has been proposed, in which the metals in the dusts react with waste polyvinyl chloride to form metal chlorides. Therefore, it is important to clarify the physicochemical properties and behaviors of zinc, lead and those chlorides and oxychlorides. In the present study, the kinetics of chlorination of ZnO, PbO and ZnFe2O4 mainly contained in the EAF dusts were investigated at 1023 K to 1273 K with Ar-O2-Cl2 gas. Based on these results, the selective chlorination and evaporation process of zinc and lead from the mixture of Fe2O3-ZnFe2O4-ZnO-PbO was examined and the high efficiency of selectivity has been demonstrated.

Jan 1, 2006

By Karen Tempel

Newmont's Lone Tree Mine is located 30, miles east of Winnemucca in Humboldt County, Nevada. Starting in February 1994 a pressure oxidation circuit was commissioned to treat refractory gold ores. Gold is leached and recovered from the oxidized slurry in a six-stage carbon-in-leach (CIL) circuit. Lone Tree has been able to maintain tighter control' of cyanide addition and reduce cyanide consumption its CIL circuit through the installation of Degussa's Cyplus® CCS Cyanide Control System in the spring of 2000. 'The Cyplus® CCS, along with additional inputs' from plant sensors, has allowed tor a more efficient and effective control strategy over the manual control method used ,in the past. This paper documents the key aspects of the Cyplus® CCS installation; the development of the control strategy, and the benefits achieved from enhanced control.

Jan 1, 1998

By Kenji Sasaki

Tamano Smelter started its operation in January, 1972 adopting FSFE ( Flash Smelting Furnace with Furnace Electrodes ) type smelting furnace at a production capacity of 101,00Ot/y of anode copper and 285,00Ot/y of sulfuric acid. Since then, it had experienced several production expansion program, it had twice as production capacity as start. 196,000t/y of anode copper and 436.000t/y of sulfuric acid. This time, we have completed the plan for increasing production capacity up to 226,000t/y of anode copper and 510,000t/y of sulfuric acid, by the oxygen enriched operation. We carried out several improvements and modifications, changing of cooling system ill FSFE, enlargement of converter and anode furnace, and some progresses in sulfuric acid plant and environmental facilities.

Jan 1, 1993