Search Documents

By Jiacheng Wang

The current state of thick seam coal mining methods is illustrated in three typical cases of thick seam longwall mining, each pointing out the outstanding achievements in top-coal caving mining and large cutting height mining in China. At the same time, based on current thick seam mining practices in China, some problems urgently need to be solved. These include improving the recovery ratio of coal reserves, determination of overburden strata pressure, shield support selection, supporting methods for large cross-section in-seam roadways, top coal bulk flow theory, and gas flow and control technology. In addition, the rational production capacity should be studied from both economic and technological perspectives in order to optimize coal recovery and efficiency.

Jan 1, 2011

By G. Skybey

The Skybolt is a new bolt concept, point anchored with resin in large diameter holes of specific sizes 38 mm and 45 mm. The new design achieves the optimum annular spacing required for mixing the resin anchor components which is essential for optimum resin bonding of the bolt to the surrounding rock. This paper explains the load transfer mechanisms between bolt/resin/rock, unique to this bolt concept. It compares the pull-out test results to those of paddle and expansion shell type bolts, and highlights the versatility of Skybolt over existing, currently used, rock support systems and the benefits mine operators can achieve when using the Skybolt.

Jan 1, 1992

By M. V. Kurlenya

The experience of application of geomechanical investigations for substantiation of extraction of undermined ore deposit in the north of Siberia is discussed. The finite element method was used for forecasting the state of massif during the development of mining works. The results of calculations were compared with the experimental data of observations in situ for evaluation of authenticity of numerical modelling.

Jan 1, 1990

By Paul A. Lu

This paper proposes an unconventional, simple, and practical method of measuring mining-induced around stresses with hydraulic borehole pressure cells. The method is a direct ground stress measuring technique. It does not require the value of deformation modulus for back-calculation of stresses; instead, it directly measures the ground stress in situ. The applicability and practicality of the technique are shown by two case studies. The technique may be applied to monitoring a stress build-up that may lead to mine roof failure or to rock and coal outbursts.

Jan 1, 1984

By A. G. Pasamehmetoglu

The swelling process is an important problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from pedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the pedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By Kenny D. Basnett

An analysis of the Roof Falls Data Base (RFDB) for underground coal mines in Illinois for the period 2004?2008 indicated that about 80% of the roof falls occur at intersections and are associated with geologic anomalies or a rapidly changing geologic environment. Most falls are associated with anomalies such as clay dikes, differential compaction faults, shear zones, joints and fractures, and geologic structure. Therefore, a better analysis of the geology with emphasis on mapping anomalies such as joints and fractures and their application is necessary to improve ground conditions and safety. Such studies within Illinois Coal Basin are limited. This paper presents a mapping study of the joint orientations with documentation of dip of the several lithological units that lie directly above the Herrin No. 6 Coal seam around southern Illinois. These units include the Energy Shale, Anna Shale, and Brereton Limestone. The mapping was done in three mines and the data were plotted on a stereographic projection to determine the average characteristics of joint planes. The study mines included two deep underground mines and one shallow highwall mine. This study has helped identify favorable mining and support orientations in areas of highly variable geology. These are currently under review by the cooperating coal company for experimental roof control studies.

Jan 1, 2011

By Zhang Liandong

Roof control in thick-seam mining has long been a difficult problem in mine design and coal mining. In the early 1980's, through ground control instrumentation and investigation the rules of roof strata movement were determined, based on which the sliding roof bar powered support was properly designed and successfully applied to roof control to thick seam mining with caving. Underground trials in Huating Coal Mine produced satisfying results. The technique is being employed in many Chinese coal mines and won the national price for technical advance.

Jan 1, 1990

By Fred Leighton

Outbursts, or the sudden and sometimes catastrophic expulsion of coal and gas into the working area of a coal mine, are a little understood and growing problem. The AE/MS (Acoustic Emission/Microseismic), or rock talk, activity prior to and associated with several outbursts has been recorded using ultrasonic and micro- seismic equipment and has been analyzed by the Bureau of Mines. Analysis of these data indicates that outbursts are comprised of several failures in rapid succession and that anomalous AE/MS data suitable for providing failure warning are generated 15 to 45 minutes prior to the failure. This paper discusses the techniques for recording and analyzing these data and presents sane case histories.

Jan 1, 1982

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The theological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By Ben Mirabile, Alan Campoli, Rodney Poland

"The majority of U.S. underground coal mines use some form of cable bolt as supplemental support to a primary roof bolting system. Many coal operators employ the high load capacity of non-tensioned cable bolts, cable roof trusses, or solid bar trusses in an attempt to suspend the primary bolted horizon to overlying strata. However, in cases where many discontinuities exist in the roof strata or where pre-existing fractures are present, these passive supplemental support systems often cannot adequately control roof deflection. This paper examines the application of tensioned cable systems to minimize roof deflection in very laminated and fractured strata. Three underground case studies are presented to demonstrate the application of tensioned cable bolts. The first case study involves the rehabilitation of a longwall head gate in the Eagle Seam with highly laminated and fractured sandstone. The second case study examines the recovery of a longwall face in the Alma Seam. The final case study addresses rehabilitation of a longwall head gate in the Pittsburgh No. 8 Seam that was developed in a sandstone channel margin area and subjected to horizontal stress concentration.INTRODUCTIONDuring the previous decade, Jennmar Corporation has recognized coal operators' increasing interest in tensioned cable bolts. The majority of these tensioned cable bolt systems have been applied in adverse roof conditions including broken ground, high horizontal stress areas, and highly laminated roof strata. In most cases, qualitative data on roof conditions after application of tensioned cable bolt support indicate successful implementation of these systems. The qualitative evidence suggests that the combination of high load' capacity and applied tension provides superior supplemental roof support in adverse roof conditions. This research aims to quantify the effects of applied tension to cable bolts. This paper will review the types and installation of tensioned cable bolt systems, present initial laboratory test data, discuss successful case studies, and propose an instrumentation system for quantification of tensioned cable bolt performance."

Jan 1, 2010

By Al Campoli

The majority of the 100 million roof bolts installed each year in the United States are 5/8 inch deformed rebar fully grouted into a one inch borehole. Commonly referred to as B-Series or No. 5 bar, this system is proven effective and cost efficient in coal mines with average to above average roof conditions. One of the critical variables affecting resin bolt performance is the size of the resin annulus, calculated as the difference between the hole and bolt diameters. The optimum annulus has been proven to be '/4 inch, which provides for effective mixing of the two polyester resin components and incorporation of the plastic film packaging within the cured resin. Glove fingering occurs when the plastic film is forced against the borehole wall potentially interfering with the mechanical interlock of the resin and the rock mass. Glove fingering is not a problem with the optimum '/n inch annulus but has been know to occur with the B-Series 3/8 inch annulus. Laboratory testing correlated the degree of Glove fingering with resin formulation and the bolt head to shaft axes alignment. Glove fingering occurred over 45 % of the grouted length of standard B¬Series bolts. The newly formulated Eclipse B-Series resin when combined with a 1/8 inch offset between the bolt head and shaft axes reduced the glove fingering 70%. The Eclipse system allows the 3/8 inch B-Series annulus to achieve the positive mixing characteristics associated with the / inch optimal annulus systems.

Jan 1, 2002

By Kent D. Mctyer

Mining commenced at Tasman Mine in late 2006. The current method of mining is bord and pillar using continuous minerbolters and shuttle cars for first workings and secondary extraction using mobile roof supports. The two stage process was chosen to accommodate irregularly shaped coal deposits, allowing adjustments to be made to extraction ratios for better management of subsidence and to maximize the efficiency of the operation. Following the completion of the first three full/partial extraction panels, the mining method was changed due to variable caving. Another partial extraction method, referred to as the Duncan Method was adopted; it involves stripping the developed square pillars on four-sides on retreat to leave a load-bearing remnant coal pillar. The system of partial extraction has been successful in meeting safety, productivity, and subsidence targets.

Jan 1, 2011

By M. O. Serbousek

In 1975 the Bureau of Mines Spokane Research Center began a series of laboratory and field tests to investigate the feasibility of developing a substitute for the organic chemicals used in resin roof-bolting systems. An inorganic system, comprised of calcinated gypsum, an accelerator, and microcapsules of water was developed and patented by the Bureau in 1977. The system has several advantages including economics, non- toxicity, nonallergenic, inflammability, and is not based on petroleum products. Two roof-bolting systems utilizing inorganic cements are under development at the Spokane Research Center--a cartridge system, using the microcapsules of water and accelerator, and a slurry system, using a mix-inject method which combines dry powder cement with water for simultaneous injection into a predrilled roof-bolt hole. Several underground field tests have been conducted in eastern coal mines. Test results indicate that inorganic cartridge systems are adequately supporting mine roof in several test sections. Economic potential for the bolt systems appears favorable.

Jan 1, 1981

By M. Zaki Rashad

In this paper, if three slant distances are measured from three given points of known coordinates to an unknown point, the position of this point (X, Y, and Z coordinates) can be determined. A computer program was designed for observing the movement of a point in the roof in Abu-Tartour mine (western desert, Egypt) to measure the convergence. This method, for general using, is very fast and can be applied without any restrictions.

Jan 1, 1990

By Thomas W. McClain

This paper describes the importance of considering ground control measures when importing U.S. continuous mining technology in foreign countries. Important ground control factors are discussed. Each year the USA exports a significant amount of continuous miner equipment (i.e. continuous miners, roof bolters, coal haulers, shuttle cars, continuous haulages, scoops and feeder-breakers). International customers see the opportunity to significantly improve their productivity and increase their longwall gateroad development rates by implementing the room-and-pillar (place changing) mining systems used throughout the USA. However, a number of issues are often overlooked or not thoroughly evaluated when selecting the equipment, often resulting in lower than expected productivity. Ground control is one of the critical factors that must be addressed. Since 1993, the author has assisted numerous international customers and manufacturers with implementing or improving the performance of continuous miner and room-and-pillar systems in Australia, India, Mexico, South Africa, and the United Kingdom. An essential first step is to conduct a thorough ground control study, and then integrate its findings into mine layout, equipment selection and section operating plans. Based on actual case histories, the author will present a number of examples and "Do's and Don'ts." Another key to success is the involvement of manufacturers and suppliers with customers when implementing new systems and technology. The importance of allowing for cultural evolution by both management and workers for acceptance and successful implementation of any new system is also discussed. Over the past ten years, the global coal industry has gone through some very dramatic changes. Countries that previously experienced a freight advantage, such as Australia shipping coal to Japan and Korea versus the United States, are finding they are now in a world coal market similar to other commodities and products. Today, coal prices arc stated F.O.B. at the consumer, and the origin is often irrelevant. Also, previously state-run coal industries have been privatized, such as the United Kingdom, and others such as Poland and India are currently going through the same transition from state-run to the private sector. In all cases, the key to continued viability, or survival, depends largely on reducing costs in order to compete for a market share. Two ways exist to reduce costs. First, almost everyone tries to reduce expenditures. Depending on the circumstances at a given mine or in a specific country, this helps to some point. However, most find that secondly, production must be increased to achieve the necessary cost reductions to compete in today's global coal market. As a result, over the past ten years, foreign companies and countries have looked to the USA for new mining methods and systems to significantly increase productivity. Thus, a major portion of American equipment manufacturers and suppliers sales have been exports, which has played a major role in helping to "keep-the-doors-open" for a number of companies through the lean 1990's, when American coal companies were postponing capital expenditures and expansions. As foreign companies and countries have looked to the USA for ways to improve productivity, they have become particularly interested in continuous miner equipment systems and most often "room-and-pillar," "bord-and-pillar" or "place changing" mining systems for four reasons. First, in countries such as the United Kingdom and Germany, who have been longwall mining for generations, there remain numerous remnant small pockets of reserves in existing mines that are either too small or too difficult to longwall mine, and are conducive to the flexibility of continuous miner systems. Second, for countries such as Australia, who have experienced the constant problem of developing longwall gateroads in a timely manner to avoid longwall move delays, new or alternate methods are required. Third, companies and countries using roadheader machines on coal production are recognizing the increased productivity potential of continuous miner equipment. Fourth, countries such as South Africa and India, where a substantial amount of the production comes from conventional mining methods, "drill-and-blast", companies are recognizing the opportunity to improve by implementing continuous miner technology. Colliers & Associates, Inc. has found that over the past eight years too often foreign companies or countries purchase American continuous miner equipment without first conducting a thorough geologic, geotechnical and ground control study for the reserves to be mined. The problems are compounded by not developing mine plans, and submitting them to the regulatory authorities for approval prior to purchasing and even implementing the equipment.

Jan 1, 2001

By Ezzeddin Bakhtavar

There are several geotechnical challenges and risks inherent in the interaction between the open-pit and block cave mining environments. This is especially true when they have to work simultaneously for a short time, as well as when only the caving operation is continued. Some of these challenges and risks include the induced zones of stress due to the large and deep open-pit, instability of the slope, instability of the crown pillar and water inflows, subsidence, and sometimes instability of the main accesses to the block cave portion of the mine. These challenges usually occur due to cave propagation. In this paper, these geotechnical challenges and associated risks have been studied and discussed. It was concluded that the majority of the mentioned geotechnical risks could be decreased, and often eliminated, by considering the appropriate dimensions of a stable crown pillar, especially in simultaneously working open-pit and block caving operations.

Jan 1, 2011

By Robert P. Kudlawiec

The use of Mobile Roof Supports (MRS) in pillar retreat mining has been a fairly recent occurrence in coal mining operations in the United States (1988). Determining the pillar block configuration, the crosscut and entry centers, the number of entries developed, the method of ventilation, and the type and mixture of equipment used arc all factors in establishing a successful pillar retreat operation. This paper will evaluate and report on the history of one coal company's relationship with MRS usage for pillar retreat mining and focus on the company's use of horizontal pillars (inverted-blocks) for the panel configuration.

Jan 1, 2000

By Robert M. Cox

Abrupt tailgate roadway ground failures, described as floor bumps, sometimes occur in the tailgate entry outby the face during the high-speed extraction of coal from mechanized longwall panels. These floor bumps typically damage the tailgate entry support structures for a distance of from 12.2 to 24.4 m (40 to 80 ft) outby the face. The relative closure of the tailgate entry may be a key indicator of potential tailgate ground control problems. Regression analyses of tailgate entry convergence data conducted by the U.S. Bureau of Mines (USBM) indicate that entry closure may be characterized as an exponential function of the distance outby the longwall face. Assuming that the entry closure is caused by the abutment loads created by the excavation of the longwall panel, the resulting convergence equation can be integrated to locate the centroid of abutment loading. This information can be used to document zones of potential ground failure ahead of the operating face.

Jan 1, 1994

By Ross W. Seedsman

The feasibility of 6 m high single pass longwalling has been studied using Newlands Mine as a case study An intensive geological investigation identified a range of hazards but a mine layout was possible that minimised the risks with respect to joints, cleats, angular bedding, coal shears and horizontal stress. Geotechnical design input was required for support capacity, subsidence, gate to face transition, face span, and roof support. It is concluded that longwall face equipment can be made available by modifying existing designs, gate to face transitions will require a number of steps, and a mid-face sprag should not be required for routine operations.

Jan 1, 1992