Search Documents

By Alan K. Burton

Massive increases in the productive capability of open pit nines after World. War II were in a large part made possible by the introduction of ever larger trucks and the supply of a seemingly bottomless ocean of inexpensive and readily accessible oil. Over a period of about 25 years, a variety of technological developments permitted a tenfold truck payload increase, from about 32 tonnes (35 tons) to 320 tonnes (350 tons). There is no, doubt that this was a remarkable achievement resulting in impressive benefits of scale as well as the ability to control what would otherwise have become an intolerable traffic congestion problem in today's large open pit mines. It became fashionable and economically possible during this time to mine large quantities of low grade material and to tolerate very high stripping ratios. As tine has gone by and as easier to get at and higher grade deposits have been depleted, ore grades have tended to decline while stripping ratios have increased. The alternative to reduced revenues has been an ever increasing demand to step up production which in turn has led to a continuing demand for ever larger and larger trucks. While a larger truck has had the effect of reducing the cost of the operator per unit of material moved and of reducing traffic congestion, it has not specifically addressed the subject of fuel cost.

Jan 1, 1981

By Borje Bjorkvall

At LKAB's plants in Lappland, Sweden, sintered pellets are manu-factured according to three different industrial processes, viz. shaft furnace at Malmberget, straight-grate at Kiruna and grate-kiln at Svappavaara. At present the total annual capacity amounts to 4.7 million tons. However, since it has been decided to erect a new straight-grate plant (2.5 million tons) at Malmberget, and because of the decision to extend and rebuild the existing plants, it is estimated that the annual capacity will be increased to somewhat over 8 million tons by 1973. The great majority of the pellets produced is exported. They are thus reloaded several times and generally speaking roughly handled, resulting in larger or smaller product losses on arrival at the point of use. It is there-fore of great economical interest to have a good control over the transport strength of the pellets by appropriate quality testing at the point of production. In addition to good transport strength, further demands are ob-viously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of in addition to good transport strength, further demands are obviously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of

Jan 1, 1972

By Andrew McGrath, Geraldine Lyons, Sarah Barcelona

In the dynamic and challenging modern industry landscape, understanding and unleashing the true role and contribution of technical teams is crucial to business success. The cyclical nature of industries has led to shifts in the technical professional’s place within the organization and the technical skills that are desired most. This paper reframes the pivotal role that technical professionals play within complex operating assets to maximize value and realize full potential. This investigation focuses on the Rio Tinto Kennecott Technical group’s cultural journey, which is underpinned by an investment in its people. The conflict between legacy industry beliefs and the necessity for cultural change emerges. This is illustrated by a deep dive into the evolving case study of Kennecott’s Bingham Canyon Open Pit Mine Technical team. Here, a multi-faceted approach to cultural change is helping to unlock the team’s contribution to the life extension of an aging asset. Guided by a vision and strategic roadmap, this approach is part way through a 5-year implementation period and is yielding encouraging business outcomes.

Feb 1, 2024

By J. Trow

Dowsing is really IESG which inductively locates electric gradients (dv/dx) on the flanks of SP anomalies. "Sensors" are in one?s head. The "meter" consists of one?s body, limbs, and two $.69 welding rods. The method was calibrated near Mamainse Point, Ontario, where IESG-negative chalcopyrite-bornite-chalcocite-native copper ores reveal mineral zoning related to the IESG-positive Keweenaw fault, down which oxidizing solutions moved. In Michigan, the IESG-positive Keweenaw fault suggests that oxygen-bearing solutions from the Jacobsville Sandstone moved downward to oxidize hydrothermal sulfur to produce native copper, and to supply sufficient water to satisfy Walter White.

Jan 1, 1992

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By Robert W. Yokom

As the search for new sources of energy and minerals leads to more remote areas of the country - and the world - the need to plan for adequate housing and community facilities for the construction and operations workforces and their families takes on an importance equal to the mining and processing facilities themselves. A corollary to the need for planning is the increasingly crucial need for development companies to devise effective strategies for dealing with the local communities impacted by these projects. Experience has amply demonstrated the high price to be paid for failure to learn this lesson, a price measured in lost productivity, confrontation with local communities, labor turnover, mental health and other social and eocnomic problems. In Sweetwater, Wyoming, a new industrial activity caused the population to double from 18,000 to 36,000 between 1970 and 1974. During that period industrial productivity fell 25 to 40 percent, cost overruns on the principal new industrial facility exceeded 33 percent, annual employee turnover rates climbed above 100 percent, the local mental health clinic workload increased nine times and complaints to the local law enforcement agency increased 60 percent.

Jan 1, 1981

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type. (1) prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution.

Jan 1, 1978

By H. Demirel

This paper deals with concentration of hematitic-limonitic iron ores. The ore sample obtained from Karakuz (Turkey) contain:. about 40-46 I Fe. First, a low intensity magnetic separation process was employed to separate the strongly magnetic particles cf "-10+2 mm" and "-2+0.075 mm" size fractions and magnetic concentrates with 59.1 % Fe aid % 58.0 Fe were obtained respectively. The non-magnetics of both fractions were then fed to a nigh intensity permanent magnetic separator. The Fe contents of "-10+2 nun" and "2+0.075 mm" size fractions were increased from 28.2 to 51.13 and from 35.4 7. to 43.25 respectively after single pass. Easing on these results, it was concluded that the high intensity permanent magnetic separator could he used as a pre-concentrator f.7.1- hematitic-limonitic Karakuz iron ore.

Jan 1, 1991

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By C. E. T. White

Although trace amounts of Indium are found in many ores, commercial production of the metal has come almost exclusively from residues, flue dusts and slags generated by Zinc recovery operations. Our paper attempts to summarize the various approaches used to recover Indium from these by-products. Some comments on production and price trends are included as well as our views on future availability.

Jan 1, 1982

By William G. Schultz

Sylvite of Canada, a wholly owned subsidiary of Hudson Bay Mining and Smelting Co., operates an 8000 TPD potash mine and refinery located nine miles North East of Rocanville, Saskatchewan. Prior to Hudson Bay's entry in 1968 into potash mining and refining, it was one of the more traditional and conservative Canadian Mining Companies whose principal business had been for many years a successful copper-zinc mining and smelting operation located at Flin Flon, Manitoba. The potash reserves being mined by Sylvite were acquired through the acquisition of Francana Oil and Gas. This acquisition was at the time when several major potash mines were being developed or had recently been brought into production in the Province. These mines are owned by either very substantial Canadian Mining Companies or Multi-National Mining Companies with considerable potash mining experience. At that time, it became very apparent because of the new mines coming into production, potash mining and refining would quickly become a very competitive industry. Because of long term considerations, Hudson Bay decided to proceed with the development of its potash reserves, recognizing the Mine and Refinery would have to be the most advanced available in order to successfully operate. This report deals with the mining operation at Sylvite and the degree of success Sylvite has achieved.

Jan 1, 1972

By W. J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 in New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be widespread through much of the Tasman fold belts of Eastern Australia. Production is estimated to be some 500,000 carats from several small alluvial fields. Despite extensive exploration, though, no primary rock source carrying significant diamond content has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia during the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives. Of those, 180 have been confirmed to be diamondiferous. Only one pipe, however, the 1200 Ma high-grade Argyle lamproite and associated nearby alluvials, has proved to be economically exploitable. Its current annual production is 40 million carats valued at about US$400 million. Production from the open pit will be sustainable until at least 2003.

Jan 1, 1995

By J. A. Ober

"In 2015, the estimated value of nonfuel mineral production in the United States decreased by 3 percent from that in 2014 (Table 1), mainly as a result of decreased metal and metallic mineral prices, especially iron ore, copper and precious metals. Lower metal prices were attributed to decreased consumption, especially in China and increased global inventories. Several U.S. metal mines were idled in 2015, including the only U.S. rare earths mine at Mountain Pass, CA. Downstream processors also were affected, with smelters and refiners either shutting down or idling production lines. Increases, however, took place in the value and quantity of production of industrial minerals, especially those used in the construction sector, including cement, construction sand and gravel and crushed stone. Trends in mineral-related sectors of the domestic economy, except for iron and steel manufacturing, aluminum manufacturing, coal mining and metals mining, all experienced growth (Table 2).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct comparisons based on weight meaningless (Fig. 1).Mineral industry performanceThe estimated value of domestic nonfuel mineral production, including metals ($26.6 billion) and industrial minerals ($51.7 billion), in 2015 declined to a total of $78.3 billion, from $80.8 billion in 2014 (Table 1). However, as shown in Fig. 2, minerals remained fundamental to the United States economy, contributing to the real gross domestic product at several levels, including mining, processing and manufacturing finished products. Net exports of mineral raw materials and old scrap were $14.4 billion. Domestic raw materials, along with domestically recycled materials, were used to produce mineral materials worth $630 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $32 billion) were, in turn, consumed by downstream industries with a value added to the gross domestic product estimated to be $2,490 billion."

May 1, 2016

By Donald A. Brobst

Barite, the sulfate of barium, occurs in many geological environments in sedimentary, igneous, and metamorphic rocks. The commercial deposits of barite may be classified into three major types. 1. Vein and cavity fillings that occur in rock fractures, along bedding planes, and in various solution structures. 2. Bedded deposits in which barite occurs as the principal mineral or cementing agent in stratiform bodies in sedimentary rocks. 3. Residual deposits occurring in unconsolidated material formed by the weathering of preexisting rocks. The geologic characteristics of each type of deposit are of fundamental importance to the successful search, development, and economic use of barite deposits.

Jan 1, 1980

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By H. Ehnes

"“Industry 4.0” – “Mining 4.0” - perhaps you have already heard of these terms? These keywords signify the next stage of industrial production. The internet and production technologies are growing closer together. Machines can communicate with one another, wherever they may happen to be located. The “Internet of Things” is the appropriate term. But what does SAFETY 7.0 mean? It is both brand new and traditional at the same time. It also has to do with the success of companies, with efficient production. And yet there is a great deal more at stake. It has to do with our lives and our safety – the supreme commodity in this world. What exactly SAFETY 7.0 means, what the number 0 stands for and the meaning of the number 7, and what this all has to do with mining will be explained in the following article. Mining is a fascinating undertaking. Mining is indispensable for a country’s economic development, whatever that may concern: infrastructure, energy supplies or raw materials for industrial production. Mining has brought forth many technological developments and innovations that can currently be found in our daily lives. Mining is impressive, grandiose and repeatedly fascinates mankind with its immense dimensions. Miners throughout the world still work hard and, for this reason, are bound to one another in a special way. In mining, every man looks out for the other; you have to be able to rely on each other. That creates a strong bond. The other side of the coin is that mining and disasters belong to normality in the media and thus also in our perception. Accidents at work and even catastrophes occur in mining, quarries, or raw material operations almost on a daily basis somewhere in the world. They are often associated with extremely serious injuries, or even a fatal outcome, for the miners affected and, in turn, dramatic consequences for the families of those involved. It could be in China, India, Russia, or somewhere in Africa, Asia or America – it mostly does not happen in front of our door or in our neighbour- hood. Perhaps because of this in the daily concert of negative headlines, we do not register these catastrophes any more in our minds. We write them off under the heading “Nothing special”, since there are, day in day out, more terrible news items about wars, civil wars, famines, or ecological disasters. Things only really change if there is a dramatic number of deaths or when we are personally affected, close by in the vicinity, or can witness the rescue action live. In Europe, these three mining disasters in particular have recently generated media resonance:"

Jan 1, 2016

By Barry A. Hillman

The rapid evolution of computer and field sensor technology is now providing the ability to integrate mine and office operations. Digital maps and mine plans as well as CAD and GIS can be transferred to ruggedized field computers for development of real-time mine surveys and real-time GPS machine navigation and monitoring. Surveyors can insure that their surveys are accurate before returning to the office. Engineers and surveyors are also able to upload field computer-based surveys to mine planning software and directly to mine equipment including shovels, drills, and dozers providing the operator of the equipment with a real-time view of their work space. Production information can be transmitted through dispatch and/or centralized mine servers to update mine plans with mining progress and production data. Static mine models then become a dynamic element of operations, providing greater use of information that emphasizes the spatial aspects of the mine by providing real-time maps, productivity charts, and graphs. This information can be disseminated through various mine communication systems to provide operators and management with real-time feedback as well as daily and weekly reports. Integrated systems now being used in extensive trials are reporting productivity increases of 4 -7% or more thereby providing rapid payback to the mine.

Jan 1, 1998