Search Documents

By Steinar L. Ellefmo, Fredrik Søreide

"The Norwegian University of Science and Technology (NTNU) and Nordic Ocean Resources AS, with support from Statoil ASA have carried out a project reviewing the knowledge about seabed mineral resources in Norway to identify and prioritize needs for further research and development.A special focus area in the project has been to increase the knowledge of possible massive sulfide mineralizations along the Mid-Atlantic Ridge. This Ridge is a subsea mountain range which separates the Eurasian and the North American continental plates. In this area, seafloor massive sulphides (SMS) are formed from the volcanic and hydrothermal activities along the Ridge. A large part of the North-Atlantic Mid-Atlantic Ridge between Jan Mayen and Spitsbergen is located on the Norwegian shelf.Analysis and interpretations of multibeam data have been carried out by NTNU in cooperation with the Russian Institute for Geology and Mineral Resources of the Oceans in order to disclose relevant areas for the formation of SMS deposits. This analysis has identified several promising areas."

Sep 1, 2014

By David Jurich, Joseph N. McDivitt

INTRODUCTION South Coast Water District (SCWD) operates the Beach Interceptor Sewer Tunnel(BIST) in South Laguna, Orange County, California between Monarch Beach and Aliso Beach (Figure 1). The 10,200-foot long BIST houses a 24-inch gravity Techite sewer pipeline critical to the SCWD Sanitary Sewer Collection System. The original tunnel and sewer pipeline were constructed in 1954 and the sewer line was replaced in 1974.Periodic inspections by sewer pipeline maintenance crews documented deterioration of specific intervals of the tunnel. Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline and a 731-foot section of tunnel located at Thousand Steps Beach was determined to be in immediate need of repairs. SCWD and consultants Hatch Mott MacDonald (HMM) and Tetra Tec prepared a Work Plan for emergency tunnel stabilization and pipe protection measures that was implemented in January 2007. Normal access to the beach and the section of tunnel requiring repairs was limited to public stairs referred to as Thousand Steps and, therefore, all materials and equipment needed for the work were transported to the beach by ocean-going landing craft. Additionally, the emergency repairs had to be completed without taking the pipeline out of service. Numerous environmental, logistical and operational requirements had to be overcome to complete the challenging emergency repairs. GEOLOGICAL SETTING The Laguna Beach area is located in the Peninsular Ranges of Southern California. The project area is located on the southwest flank of Niguel Hill along marine wave-cut cliffs and slopes. The tunnel was excavated in the San Onofre Formation, a marine deposit, characterized by abrupt lateral and vertical changes in lithologies that vary from boulder to cobble and gravel size breccias to medium coarse sandstones with gravel, sandy claystone and siltstone. The interval of the tunnel that required repairs is located within the San Onofre breccia, a moderately-to-well cemented, poorly bedded to massive unit with angular to subangular boulder and cobble sized clasts of schist. The sandy silt matrix of the breccia is composed of quartz, feldspar and schist grains (Figure 2). GENERAL TUNNEL DESCRIPTION The approximately 6-feet high by 6-feet wide 10,200-foot-long BIST was hand mined in 1954 at the base of the coastal cliffs. Primary access is through twenty-one access adits from public and private beaches. The tunnel is located in an easement that extends beneath private property with residential structures situated 50 to 80 feet above and horizontally in close proximity to the tunnel alignment. Most of the tunnel is horse-shoe shaped and unsupported, but approximately 3,000 feet is supported by timber

Jan 1, 2007

By K. A. Lewandowski

Leach heaps are plagued with problems due to fine material migrating downwards, clogging the spaces between the coarser ore particles, resulting in decreased metal recovery rates. The use of a binder in agglomeration would allow the fine material to be immobilized, increasing the availability for the solution to come in contact with all the ore. As much as 1.64*1012 BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, assuming that 70% of heap leaching units converted to using agglomeration technology. This is equivalent to approximately 18% of the energy currently being used in leaching heaps.

Jan 1, 2008

By Albert Musschoot

The expanding applications of vibrating feeders for controlling the flow of bulk materials, and their adaptation for processing requirements, have developed considerable interest in stockpiling and reclaim systems. The general design of these units consists of a material transporting trough, or platform, driven by a vibratory force system. Design flexibility and variety is limited only by engineering ingenuity. The basic motion of the vibratory trough, or work member, is a controlled directional linear vibration that produces a material tossing or hopping action. Material travel speeds vary from 0 to about 30 m/min, depending on the combination of frequency, amplitude, and slope vibration angle.

Jan 6, 1981

By Russell Miller, Fun-Den Wang

High Pressure Water Jet Assisted Tunneling The high pressure water jet assisted tunneling project was conducted in a granite quarry near Skykomish, Washington, approximately 90 miles east of Seattle. A 7-ft diam tunnel boring machine was modified and equipped with high pressure water jets. The concept that tunneling rates can be improved by using high pressure water jets was validated, with an average increased advance rate of 50% to 60%. For some tests, the advance rate was more than doubled. A comprehensive economic analysis has shown that very significant savings are possible. At a 50% increase in advance rate, cost savings of 14% and 24% were projected for 10-ft and 20-ft diam tunnels respectively. These benefits were seen to be relatively insensitive to water jet equipment costs.

Jan 1, 1976

By James F. Kvitkovich, George V. Weisdack

Editor’s note: This is the second part of a two-part series on longwall mining in the United States. Part one was published in the December 2005 issue of ME (pp. 21-26). It provided a history of longwall coal mining in the United States. It also discussed the technology involved in the productivity gains and operational improvements. Boyd anticipates that U.S. coal production will increase by 61 Mt (67 million st) (6 percent) from 2004 to 2010. A combination of higher surface and underground mine production will be required to meet the projected market demand. Boyd’s projections of coal production by major mining methods are shown in Table 1.

Jan 1, 2006

By Daryl E. Radcliffe, Raymond M. Stateham

The Bureau of Mines, under a Cooperative Agreement with the Bear Coal Company, Somerset, Colorado, conducted a large scale evaluation of the effect of time lapse on roof stability. Time lapse in this study is the interval between exposure and permanent support of the mine roof. The study indicates that time lapse is not a critical factor in roof stability provided permanent support is installed before catastrophic failure begins. Concurrently with the time lapse study, investigations were made of stress distribution around resin-grouted bolts, the regional stress field, and anomalous geologic conditions. The behavior of the resin-grouted bolts, at least in the Bear mine, appears to fit the Coulomb-Navier Theory. Geologic conditions are primary factors in trends of roof stability that extend across the mine.

Jan 1, 1982

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By Gary N. Weinrich

Large surface mining projects in sparsely populated regions of the West have the potential to create disruptions in an area's social and economic character with potential effects on man that can far outweigh the physical and ecological effects on man's environment. The data and analyses involved in addressing the socioeconomic issues are additional to those traditionally associated with surface coal mining, such as those concerning land reclamation and water quality. Appropriate socioeconomic studies in conjunction with mine-planning can identify the potential problem areas in order that project measures can be taken to maximize the beneficial impacts and minimize the adverse effects of surface coal mining. The information required to conduct such socioeconomic analyses, available data sources, and the applicable analyses are described. Overall impacts of some proposed Western surface mines are summarized and potential mitigating steps discussed.

Jan 1, 1975

By James L. Poole

The gold and silver markets from the late 1960's to the present are reviewed and the outlook for these metals in the 1980's is presented. Included in this discussion is a summary of the basic supply and demand balance for gold and silver since the mid-1960's. an explanation of the price formation for the metals, some of the relationships between the prices of these metals and selected economic parameters, and how these factors affect the outlook.

Jan 1, 1981

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By Dan Witkowsky

For the 36th consecutive summer, the Colorado Mining Association Education Foundation and the Colorado School of Mines have sponsored “A Total Concept of the Mining Industry” for kindergarten through grade 12 teachers. Teachers from 34 states, plus the District of Columbia and two foreign countries, have graduated from the four-week course. They received six hours of recertification credit. This summer 31 teachers from Colorado, Kentucky, Virginia and Alaska completed the program. The course is unique from other shorter courses in that it solicits teachers of all disciplines from all K-12classes. In addition to the expected earth science and mathematics teachers, the Class of 2004 consisted of educators who teach music, chemistry, biology, social studies, history, basic English and world history. Others in the program included those who teach American history, physical and life science, remedial reading, consumer/family studies, “world of work,” language arts, engineering technology, environmental science, world geography, human anatomy and physiology, and business.

Jan 1, 2004

In this paper, a mixed integer linear programming (MILP) model for the short-term scheduling of open pit mines is formulated. The proposed model aims at sequencing the blocks extraction over multiple short-term periods. The model takes into account multiple processes, waste dumps, and multiple stockpiles. The short-term scheduler makes a decision on the period, destination, and route that ore and waste are supposed to take to minimize costs while meeting all the mining and processing constraints. The destinations of the extracted materials are also controlled by their rock types. A monthly short-term production scheduling case study of an iron ore deposit is carried out over a year to validate the model.

Jan 1, 2011

By C. Okrusch, C. Roos, M. Akers, S. Rosenthal

Modern mining consistently faces controversy. Public sentiment impacts the permitting and development of mines, so a quality public relations (PR) program for mining companies may improve society’s impression of the mining industry. Developing mines face more permitting challenges than operating mines, which stems from a lack of societal trust given the history of mining and its impact on the environment. Two case studies were selected based on the type of public controversy they face to demonstrate how pervasive permitting issues are in industry. Both Pebble Mine, owned by Northern Dynasty Minerals (NDM), and Black Butte, owned by Sandfire Resources America Inc (SRA), experienced difficulties with their water permitting due to potential risks their mine developments posed to local fish populations. Pebble has, to date, failed in all of their attempts to become permitted due to concern for the water and the fish. Black Butte dealt with the same problems, on a smaller scale, but was able to become permitted. These two mines will be discussed in detail including local history, mine setting, mining history in America, prevalent culture groups, technology development, and intercultural communication competence (ICC). The mining industry needs to evaluate its ICC skills since ICC directly determines the effectiveness of PR. Based on Barna’s Stumbling Blocks for intercultural communication, methods for improving the mining industry’s PR will be suggested in the hope of easing the permitting process for future mines by developing ICC.

Mar 2, 2022

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.

By Tom Szaraz

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer?Part II (BWOAS) consists of 13,200 feet of tunnel of 12-foot tunnel passing mainly through glacial deposits with a water head of up to 2 bar. A Lovat RME167SE was used to drive this tunnel with steel fiber reinforced precast segmental liner used for support. This paper will discuss the concepts for tunnel sup-port and TBM selection, the problems encountered with the TBM sealing systems and the solutions used to repair the machine.

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By James L. Weeks

Introduction This paper attempts to summarize some of the major criticisms of drug testing. Eight problems with drug testing are discussed. These are: • It does not measure something employers have a reasonable need to know, • It is a distortion of priorities, • Drug use is not known to be associated with increased risk of occupational injuries, • Drug testing is proposed as a dangerously simplistic solution to poorly conceived problems, • In the absence of safeguards, it is unacceptably inaccurate, • In the absence of treatment commitments and confidentiality protection for persons dependent on drugs, it is an unethical practice of medicine, • Drug testing is an invasion of privacy, and • It will have a negative effect on treatment of persons with drug or alcohol dependencies. Employers' need to know It does not measure something employers have a reasonable need to know. It is reasonable for employers and fellow workers to want to know if workers are functionally impaired (intoxicated) while on the job. Drug testing does not measure impairment. It measures the concentration of drug metabolities in urine or blood. Unlike measurements of blood alcohol concentration (BAC), drug metabolites are not correlated with impairment or intoxication. They indicate only drug use in the one to two weeks before a urine sample. And, in some instances, they indicate chronic use. Impairment caused by drug use, on the other hand, occurs immediately and declines rapidly within hours. Drug metabolites may linger for days afterwards. Drug metabolite concentrations in urine are a function of (Morgan, 1984; Schartz and Hawks, 1985; MMWR, 1983): • the amount and purity of drug consumed before taking the test, • when the drug was consumed, • whether the person was a chronic user, in which case a certain amount of drug metabolites would be stored in body fat and slowly released, • the person's metabolic rate, and • for metabolites in urine, any dilution effects of urine. Only the first two factors has

Jan 11, 1987