Search Documents

By C. Treworgy, C. Chenoworth

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Feb 24, 1997

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009

By Ray Brainard

The subsurface investigation for the Reach 4 Tunnel was expected to be completed in a single phase. This assumed that data from two nearby previous tunnels, combined with limited new subsurface information and surface mapping would be sufficient to characterize the rock behavior. Unforeseen rock conditions and complex faulting led to the recommendation for a second phase. This decision was not reached easily, as much of the follow-on work required helicopter support, and associated costs. The second phase of drilling found significantly more variability than the first phase and led to a very different and better understanding of the geologic and geotechnical conditions, and rock characterization.

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By A. Founie

The United States continues to be the world’s leading producer and consumer of diatomite. Production of diatomite in the United States during 2004 was estimated to be 635 kt (700,000 st). This was a 2-percent increase from 2003. The value of processed diatomite in the U.S. was about $164 million in 2004. Production was from six companies with 13 processing facilities in four states. Nevada and California were the principal producing states. They accounted for about78 percent of the U.S. production during 2004. U.S. diatomite exports were about 136 kt (150,000 st). Imports were negligible.

Jan 1, 2005

By R. Hedin, M. Dunn

The Pennsylvania Department of Environmental Protection (US EPA 319 program) provided funding to aid a public-private effort in the installation of an environmentally-friendly system to treat abandoned mine drainage at Jennings Environmental Education Center (Pennsylvania Department of Conservation and Natural Resources). Through this cooperative effort among state and federal agencies, mining, excavation, and environmental companies, college and home school students, Girl Scouts, and volunteers, a successful multi-component passive system, readily accessible for upgrades and public education/research activities, was built. 90 people were directly involved in construction of this award-winning system and about 1000 people annually benefit from the educational opportunities.

Jan 1, 2002

By Steve Kral

The mining industry is no stranger to hard times. Throughout its history, the industry has faced the ups and downs of commodity prices, difficult-to-mine-and-process ore bodies, labor issues and other problems. Throughout it all, though, the mining industry continues to provide the materials needed for society —even in the face of attacks by those who seek to cripple the industry or have it go away. The reason the mining industry survives, of course, is that mankind requires the products the industry produces. And, in recent decades, the industry has developed new technologies and improved on existing ones to produce those products in environmentally sound ways. At the same time, the economic benefits have been enormous to communities throughout the world where mining takes place.

Jan 1, 2002

By Aleksandar D. Bugarski, Dylan A. Ritter

The results of laboratory characterization of tailpipe emissions for three “clean” engines that meet U.S. EPA Tier 4 final emissions standards were used to assess the viability and effectiveness of repowering existing engines and powering new mobile equipment with those engines as a control strategy for reducing exposure of underground miners to diesel aerosol and criteria gases. The evaluated engines were representative of those that achieve the emission standards through implementation of various in-cylinder emissions control strategies, use of crankcase filtration, and use of three types of exhaust aftertreatment systems: (1) diesel oxidation catalytic converter (DOC), (2) combination of DOC and the full-flow wall flow monolith diesel particulate filter (DPF), or (3) combination of DOC, diesel exhaust fluid (DEF) based selective catalytic reduction (SCR) system, and ammonia slip catalyst (ASC). The study showed that the highest reductions in concentrations of diesel aerosols in underground workings, in terms of both mass and number, could be achieved if the engines, preferably in all power classes, are fitted with viable DPF systems. The use of U.S. EPA Tier 4 final engines equipped with DOC and DOC/SCR/ASC systems could help operators to considerably reduce mass, but not number concentrations of aerosols. The emissions of two of the evaluated engines, one equipped with DOC and the other equipped with DOC/DPF systems, were characterized by substantial secondary NO2 emissions that would limit the viability of those engines for underground mining applications. It appears that the catalyst formulations used in the exhaust aftertreatment systems of the “clean” engines marketed to the underground mining industry need to be formulated to minimize the potential for generation of secondary NO2 emissions. The results indicate that the engines fitted with viable SCR/ASC systems present a low-NO2 alternative. All three “clean” engines were found to have low CO output. Therefore, due to nuances associated with the use of diesel-powered mobile equipment in underground mines, special attention needs to be paid to the selection and potentially optimization of “clean” engines for underground mining applications.

Feb 1, 2025

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

By A. Mayton, W. Porter, A. O’Brien

In 2004, management at Unimin’s Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

Jan 1, 2007

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By W. G. Willson, Y. L. Li, P. D. Rao, D. E. Walsh

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. The objective of this study was to subject two Alaska low-rank coals to hydrothermal drying to enhance their marketability in the Pacific Rim markets and to evaluate the chemical and physical properties of the dried products as a function of process conditions. Coals from Usibelli Coal Mine and the Beluga coalfield have a heating value of approximately 18.5 MJ/kg and contain about 28% moisture. Hydrothermal treatment (at 275° to 325° C) of lump coal, from the Usibelli Coal Mine and the Beluga coalfield, enhanced the heating value of the material, on an equilibrium moisture basis, from 18.5 MJ/kg to nearly 27.8 MJ/kg. The product coal, with a high heating value and only 0.2% S, is an environmentally-acceptable premium fuel; additionally, with the Hardgrove grindability index of the coal greatly improved, its value is even further enhanced. An increase in hydrothermal drying temperature promotes vesiculation of resinite. Also, ulminite reflectance increased to 0.92%, and ulminite was subjected to widespread vesiculation; this resulted in a coke-like structure indicative that the material went through the fluid stage.

Jan 1, 1993

By T. Yegulalp, M. Castaldi

As global energy demands increase, there will be a critical need to employ fuels that have minimal environmental impacts. While hydrogen is considered the ultimate fuel for that purpose, hydrocarbon based fuels will be in use for a considerable time and will probably be the first major source of hydrogen for next generation power systems. The best fuel for this transition will be natural gas because of the high hydrogen to carbon ratio. Natural gas hydrates have the potential to meet the global energy needs for the foreseeable future. The amount of energy stored in natural gas hydrates is significantly more than that of all the other fossil fuels combined. However, most proposed techniques for recovering the natural gas from the hydrate require too much energy input, raise safety concerns or can only recover a fraction of the gas. This paper discusses the technical feasibility of a novel method of gas production in hydrate reservoirs. The method is an in-situ process that creates a point heat source in the hydrate formation. This method not only significantly reduces the energy input, but also has the potential to sequester as much or more CO2 than would be produced from combustion of the natural gas produced, thus making this in-situ methane production technique virtually carbon neutral. Simulations using FEMLAB™ show that the method offers an energy efficient and environmentally friendly way to produce natural gas from hydrate reservoirs. Preliminary results indicate that it is possible to have an energy efficiency of nearly 90% for land based reservoirs for hydrate loadings of 20%. The simulation results also suggest that alternatives to a point source can be employed which may improve the process efficiency.

Jan 1, 2007

Thallium is an uncommon heavy metal that may be found in concentrations that exceed regulatory limits in mining influenced water associated with processing cadmium, copper, gold, lead, and zinc ores. This study evaluated cost-effective modifications to lime precipitation treatment to reduce thallium concentrations to below the EPA drinking water MCL of 2 ppb. The oxidative precipitation of Tl+ to Tlß+ by potassium permanganate was explored for thallium removal at low concentrations (1 ppm initial thallium). Laboratory batch tests were performed to evaluate the removal of thallium from synthetic solutions. Three ratios of potassium permanganate to oxidizable metals in solution were used (one-half, one and two times stoichiometry). Thallium was removed to less than 1 ppb for all stoichiometric ratios evaluated within 10 minutes of reaction. The efficacy of oxidative precipitation for thallium removal is presented.

Jan 1, 2011

By E. A. Metz

Perfect combustion in an engine would produce only water vapor, carbon dioxide and nitrogen as by-products; however, complete combustion is never achieved. As a mobile power plant, the diesel engine is relatively inefficient in terms of energy produced from the energy potential of the fuel. The diesel is not a perfect engine. The fuel burned can undergo a very large number of reactions in the combustion chamber. It only stands to reason that a large number of compounds are contained in the exhaust, actually, thousands of chemicals. The exhaust can be broadly divided into a gaseous phase and a particulate phase. Each phase is made up of organic and inorganic compounds. The vapor phase contains carbon monoxide, sulfur dioxide, various oxides of nitrogen and many hydrocarbons. The particulate phase contains clusters of respirable inorganic particles made mostly of carbon. This paper will address the health hazards, as we know them today, of the major components of the particulate phase in the exhaust of diesel engines. It will briefly examine the operational factors of the diesel engine as it applies to particulate emissions. Longitudinal studies of occupationally exposed miners are needed with documentation of levels of exposure before a chronic effect of exposure can be determined. At this time, it is not possible to conclude from human studies the level of diesel exhaust exposure that results in the observed lung cancer risk.

Jan 1, 2001