Search Documents

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020

By S. Zhang, Z. Hua, D. Feng, X. Tong, X. Xie

The separation and beneficiation of low grade collophanite has long been a technical challenge in phosphorous production. It requires the joint efforts of process design, reagents optimisation and operational control. In this study, the statistical response surface method was applied for determining the optimum reagent dosing in the flocculate flotation of a low grade (18.59%) collophanite ore. The dosage of three reagents, including a pH regulator (Na2CO3), depressant (Na2SiO3) and flocculant (modified starch), were input parameters of the modelling design. Two quadratic mathematical models were derived for prediction of grade and recovery based on the statistical design. Statistical analysis of the experimental results validates the reliability of the models. Through further calculation, the optimum dosage of the three reagents were found to be 3,020g/t Na2CO3, 1,990g/t Na2SiO3 and 880g/t modified starch, with which a maximum recovery of 75.81% and P2O5 grade of 30.08% was obtained from flocculate flotation test. Keywords: Process optimisation, modelling, froth flotation, collophanite ore, response surface methodology

Jan 1, 2020

1. Book reviews Dislocations and properties of real materials, edited by M.H. Loretto. London, The Institute of Metals, 1985. 392 pp. Reviewer: F.R.N. Nabarro Au &Ag heap and dump leaching practice, edited by J.B. Hiskey. AIME, 1984. 162 pp. $20 (member), $15 (student member), $30 (non-member) plus $3.50 for postage and handling. (Order from SME Books, Caller no. D, Littleton, CO 80127, U.S.A.). Reviewer: R.A. Snodgrass The cost and availability of Colombian coal, by Eric D. Jamieson, with the assistance of Kathleen Jamieson. London, lEA Coal Research (14/15 Lower Grosvenor Place, London SWl W OEX). £50 (in member countries), £100 (in non-member countries). Reviewer: W.C. Mather Extraction Metallurgy '85. London, The Institution of Mining and Metallurgy, 1985. £42. Reviewer: R.A. Snodgrass 2. Recent publications Mining annual review 1985. London, Mining Journal, Jun. 1985. 600 pp. £26.50 (surface), £39.50 (air). High heat production (HHP) granites, hydrothermal circulation and ore genesis. London, The Institution of Mining and Metallurgy, 1985. 593 pp. £27 (members), £30 (non-members). Potential mineral resources of Egypt. 144 pp. US$10. Available from Bendix Field Engineering Corporation-MPGAP, Box 1237, Grand Junction, CO 81502, U.S.A. 3. Mintek reports Report M212 South African costs of equipment for the metallurgical industry (1984). Report M213 The response of as-rolled 3CR12 steel to heat treatment. Report M214 A computer programme for use in the development of multi-element X-ray-fluorescence methods of analysis. Report M221 Commodity profiles for selected metals. Report MIO7D Upgrading of alaskite rock to feldspathic sand. (First issued Jun. 1983; reissued Nov. 1985). IMM awards Given below are details of the trust funds to which applications are invited for grants, etc., payable in 1986. Application forms, which must be returned to the Secretary before 17th March, 1986, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1986

By I. O. Flores, A. Anani, H. Li

Current technological advancement has increased the exploitation of deeper ore bodies using underground methods. In certain cases, the mineral deposit starts near the surface and continues deep within the earth's crust. Such deposits are best mined with both underground and surface methods. Two main techniques are used to determine the optimal transition depth from surface to underground - a disintegrated approach and an integrated approach. Both methods have limitations in their use to determine the optimal transition depth. The objective of this research is to investigate the conditions in which an integrated approach to the transition depth problem is superior to a disintegrated approach. Three binary integer linear programming models are developed for this purpose: a surface and underground model for the disintegrated instance and an integrated model. A case study is performed to validate the models, with a comparative sensitivity analysis to obtain operational insights.

Sep 1, 2021

COUNCIL AND STANDING COMMITTEES, 1974-1975 Office Bearers : Prof. R. P. Plewman (President), Dr R. E. Robinson and Dr M. D. G. Salamon (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and P. W. J. van Rensburg (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, E. Collier, G. H. Grange, Dr P. R. Jochens, Dr D. I. Legge, D. G. Malan, C. T. Shaw, L. W. P. van den Bosch, D. A. Viljoen, H. M. Wells, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), D. A. Smith (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza (until May 1975), H. Britten, H. E. Cross, Prof. J. de V. Lambrechts (until December 1974), R. C. J. Goode, Prof. D. D. Howat, Dr J. P. Hugo, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing and sub-committees held 74 meetings. COMMITTEE CHAIRMEN Membership, Dr M. D. G. Salamon; Technical Programme-Metallurgy, D. A. Viljoen; Technical Programme-Mining, G. H. Grange ; Vacation School-Metallurgy, Dr P. R. Jochens; Vacation School-Mining, Dr M. D. G. Salamon; Awards, Prof. R. P. Plewman; Excursions, Dr D. I. Legge; Constitution, Rules and Policy, P. W. J. van Rensburg and Prof. R. P. Plewman; Mines and Works, P. A. von Wielligh; Education, P. W. J. van Rensburg. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies Members: V. C. Robinson and Prof. R. P. Plewman. Alternates : Dr R. E. Robinson and Dr M. D. G. Salamon. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg. Alternates : Prof. R. P. Plewman and G. H. Grange. South African Council for Professional Engineers Member : R. C. J. Goode. Alternate : G. H. Grange. Engineers' Liaison Committee (Pretoria) Member: Dr J. P. Hugo. Alternate: P. W. J. van Rensburg. MEMBERSHIP Thirteen Fellows, seventeen Members, eleven Graduates, three Associate Members, eighteen Associ¬ates, twenty-six Students, and one Company Affiliate were elected during the year. Nine Fellows, four Members, and three Associates were admitted to retired membership. Eight Fellows were elected to Honorary Life Membership. Three Members and one Graduate were transferred to Fellows, nine Graduates and two Students to Members, six Students to Graduates, one Student to Associate, and one Associate to Associate Member. Six Fellows, ten Members, three Associates, and one Student resigned. A statement of membership as at June 30th 1975 and the end of the previous year is shown in the following tabulation: 30th - 30th June, - June, 1974 - 1975 Honorary Life Fellows - 9 - 15 Honorary Fellows 8 - 8 Life Fellows 170 - 170 Fellows 544 - 536 Members 512 - 523 Associate Members 10 -15 Graduates 130 - 133 Associates 194 - 210 Students 173 -175 Company Affiliates 70 - 71 1 820 - 1 851 [ ] OBITUARIES Your Council records with deep regret the death during the year of the following members: M. Barcza, Honorary Life Fellow and Past President of the Institute; J. A. Boyd, F. E. Keep and J. H. Taylor, Life Fellows; I. D. B. Corner, C. O'G. Deane, R. E. Gilmour, A. C. Hofmeyr, M. W. Howell, T. J. Robin and F. C. Steinhobel, Fellows; J. J. Frankel, Member; T. J. Higgs, Associate. FINANCE The annual accounts, which follow this report, indicate that income again exceeded expenditure by a margin of R21 410 (last year R28 524). This year's income of R71 184 showed a further increase compared with last year's figure of R55 025. Costs, however, also in¬creased, and it is calculated that, excluding non-recurrent costs, the cost of running the Institute in¬creased by R6 654 from R25 501 to R33 155 for the current year. The main increases were involved in secretarial fees, stationery and print¬ing, and in publication of the Journal. All indications are that costs will continue to rise, and we have been advised that the A.S. & T.S. will be increasing their secretarial fees by 25 per cent in the year ahead to meet their rising costs. This year's surplus was derived entirely from the revenue from sales of publications (R13 644) and a surplus from the 1974 Winter School (RIO 654). There can be no certainty that revenue from these sources can be repeated each year. Our funds are in a satisfactory position because of these worth¬while activities, but the administrat¬ion of the Institute should not de¬pend on them. Council will accord¬ingly have to give consideration in the year ahead to an upward adjust¬ment of subscriptions to meet rising costs.

Jan 10, 1975

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

By L. D. Robbins, M. L. Murphy, A. C. Campbell, L. Murphy

This paper reports on what appears to be the first discovery of prehistoric mica-schist mining in southern 4frica. The mine concerned was found in a location very rich in rock art that is one of the most important archaeological sites in the Kalahari. The authors conclude that the oval pieces of mica schist that were found at the mine site were used by Khoisan peoples to scrape fatty tissue from hides that were to be cured. Radiocarbon datings seem to indicate that such ovals were used for at least 20 000 years.

Jan 1, 1994

By C. Massola, E. E. M. N. de Guzmán, M. G. Bergermana

The abrasiveness of a mineral or rock is an extremely important topic in the mining industry and is generally measured by the Bond abrasion index (AI). However, to determine such an index by the Bond test requires 1,600 g of sample with particle sizes ranging from ½” to ¾”, which are not available in certain situations, such as ore prospecting, drilling, and geometallurgical studies. In order to investigate the abrasiveness of smaller-sized sample materials, a modified LCPC test was developed, which allows testing fine materials (i.e., 1.0 mm or smaller) to predict wear in ore processing circuits and anticipate possible failures resulting from changes in abrasive characteristics of the ore being processed. The results for 16 different materials indicated a good correlation with the AI and the modified LCPC, resulting in a reliable alternative for the AI. Keywords: Bond Abrasion Index (AI), LCPC, abrasiveness

Jan 1, 2020

By E. S. van Druten, M. C. Bekker

"The complete and successful closure of a mine in the South African environment remains problematic. Closure remains an elusive mining phase due to unclear roles and responsibilities, inaccurate closure management data, and the inability of stakeholders to conceptualize and integrate closure information into business processes. Currently there are no proven methods available to address the complexities encountered during a closure application, and to date no mine has been granted full closure. Many mines are left abandoned and unrehabilitated, resulting in risk to investors, surrounding communities, and regulators. This investigation aimed to determine, categorize, and rank reasons for unsuccessful mine closures. Focus groups consisting of public and private stakeholders were identified and surveyed through a structured, rank-order questionnaire to determine the relative importance of reasons why achieving formal and final mine closure remains elusive. Various requirements and aspects were identified and listed according to four categories: namely, primary, secondary, process drivers, and information sources. These aspects should be considered in the development of an integrated mine closure model.Background and rationalePrior to 1956, mine closures were not subject to legislative requirements, being merely governed by insufficient environmental regulations under the Mines and Works Act 27 (MWA) (Swart, 2003). In 1981 the Chamber of Mines (COM) published a document titled ‘The rehabilitation of land disturbed by surface coal mining’, which constituted the first notable contribution to environmental protection. This guideline was later referenced in the Minerals Act of 1991, which for the first time laid definite environmental burdens on the Mining Right Holder (MRH). The Minerals Act of 1991 was superseded by the current Mineral and Petroleum Resources Development Act (MPRDA) and the Mineral and Petroleum Resources Development Act Regulations (MPRDAR), which specify a regulatory process for mine closure applications and financial provisions."

Jan 1, 2017

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

By F. J. N. Bruwer, T. R. Stacey

The research described considers whether the variability in coal material strength, as derived through a series of uniaxial compressive strength (UCS) tests, could be used to indicate the variability in coal pillar strength. The aim is to be able to use a distribution of UCS tests as input into the coal pillar strength calculation. This will allow the pillar design to be expressed in terms of a probability of failure rather than as the commonly used safety factor. To achieve this, the bulk strength factor associated with commonly used pillar strength formulae was replaced with a distribution of UCS results divided by an adjustment factor. The factor was determined so as to ensure that the resulting bulk strength does not deviate from the statistically determined bulk strength published in the original formulae. This approach enabled pillar strength distributions to be obtained using industry-accepted strength formulae, subsequently allowing for a probability of failure to be calculated for a specific pillar design. Using a regional coal material strength curve as a baseline, coalfields in which the coal is stronger than the regional mean can be identified and the pillar designs optimized. This is based on the stronger coals achieving lower probabilities of failure at similar safety factors. The research has considered actual UCS data from multiple mines in the Mpumalanga coalfields of South Africa, and has proved that the variability in material strength between coalfields could allow for some optimization using the proposed approach. Based on the data used in the study, a 2.78% increase in extraction could be achieved. However, further research will be required to validate the results of the study in an underground environment.

May 3, 2023

1. Book review • World mineral statistics 1974 to 1978. Production: Exports: Imports. London, H.M.S.O., Institute of Geological Sciences, 1980. (Reviewer: R. P. King) This edition is the third in a regular series prepared by the Institute of Geological Sciences. It is a useful compilation of statistics on the production, export, and import of fifty-eight different mineral commodities. Each mineral is listed by country, and a table is provided for the annual production, the annual imports, and the annual exports for each commodity included. However, some commodities are treated in considerably more detail; for example, aluminium and bauxite have tables under the following headings: Production of Bauxite, Production of Alumina, Production of Primary Aluminium, Exports of Bauxite, Alumina and Aluminium, Imports of Bauxite, Alumina and Aluminium. The information presented is the latest official information available from primary sources; the compilers have not relied on data from secondary compilations. This publication will be of considerable assistance to all who are concerned with the trading of mineral commodities and their production.

Jan 1, 1981

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI. However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI. In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By O. S. L. Bruinsma, M. J. Matsela, D. J. van der Westhuizen

The free ligand (FL) model is an intuitive model to calculate the equilibrium concentrations in solvent extraction (SX) based on the distribution coefficient (Kd) at infinite dilution and the fraction of free ligand available for extraction. In this work, the FL model is validated to account for co-extraction of Ni and for designing the extraction and scrubbing sections of Co/Ni separation in a base metal refinery. Cyanex 272 is employed as a selective Co extractant in the process to yield high purity Ni. To enhance the loading capacity of the extractant, 50 mol% of NaOH is pre-loaded into it. Experimental and FL modelling results show that four equilibrium stages are required to purify the 99% Ni feed to a 99.97% Ni raffinate. The 53.59% co-extract with 26.76% free ligand is purified with a reflux scrub of 30 g Co/L in one equilibrium stage to 99.01%, Co in the scrubbed extract. The FL model as well as the Co/Ni/Na-analysis of the aqueous phase confirm that in the scrubbing section, Ni in the extract is mainly replaced by Co. Finally, in the one stage stripper the Co concentration in the scrubbed extract is increased from 5.6 g Co/L in the extract to 30.5 g Co/L that is partially used as reflux scrub liquor.

Dec 11, 2024

By A. M. Bauristhene

Ti-64, which accounts for more than 50% of the worldwide titanium tonnage, has found commercial importance in industries requiring components with high specific strength and resistance to corrosion. Investment casting is the preferred production method due to the difficult machinability of the alloy. This study was aimed at investigating the mechanism and the extent of alpha case formation on Ti-64 components cast using the investment casting method with YFSZ (yttria fully-stabilized zirconia) shell moulds after vacuum induction melting. The extent of the reaction between the mould hot face and the molten metal has been studied by varying parameters such as soaking temperature and mould hot face composition, and examining their effects on the reaction with the mould. An increase in the soaking temperature had an effect on the alpha case, both in appearance and hardness, but had no effect on contamination levels by carbon, oxygen, and nitrogen. The depth of alpha case increased with soaking temperature, increasing from 35 µm to 161 µm with an increase in temperature from 1200°C to 1400°C. The micro-hardness profiles provided insight into the effect of the alpha case on the mechanical properties of the Ti-64 alloy by displaying hardness values of 1000 HV0.1 and above, but could not be solely utilized to determine the alpha case penetration depth due to microstructural differences in the unaffected Ti-64, in particular the martensitic microstructure that formed with a fast cooling rate from a higher temperature. Levels of expected contaminants such as Zr, Y, 0, and C were low. The addition of the colloidal zirconia binder affected the interfacial reactions. YFSZ proved to be a thermodynamically stable refractory material, with the alpha case possibly forming as a result of segregation.

Jan 1, 2013

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

The January General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th January, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present eighteen Members, including Messrs F. P. Bath, H. Britten, J. K. E. Douglas, P. Lambooy, V. C. Robinson, W. T. Stobart and P. W. J. van Rensburg (Council Members), Messrs J. C. Hall, P. C. Pirow, Dr D. I. Legge, Messrs E. R. Rudolph, H. R. Reid, Dr N. Stutterheim, Messrs B. F. van der Merwe, L. W. P. van den Bosch, D. T. Watt, M. Youngworth and T. Zadkin. Two Associate Members, Dr P. R. Jochens and Mr D. A. Viljoen. Two Students, Messrs R. P. W. Henrard and D. Ossin. Sixteen Visitors, including Messrs I. Barnes, B. F. Bath, S. Botha, P. A. du Plessis, K. Edwards, Dr F. S. Fulton, Messrs H. Grant, B. Havenga, L. Kok, Dr D. Lasar, R. Sandler, C. W. Wolhuter and J. D. Young. Secretary, Mr D. C. Visser. Total present: Forty. MINUTES The President: "May we confirm the minutes of the meeting held on the 20th November, 1968, as published in the December, 1968, issue of the Journal?" Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Basil James Jackson and James Petrie Archibald. Associate Members: Ronald Creasy, Hugh Angus McCallum and John Barton Cunliff. Graduate: Hermanus Isak Johannes van der Merwe. Affiliate: Edgar Ramsay. Student: Petrus Daniel Wolmarans. MEMBERS TRANSFERRED TO A HIGHER GRADE From Affiliate to Associate Member: Neil Bradfield and Mervyn Bayard Allman. "I welcome the newly elected members to the Institute and congratulate those members who have been transferred to a higher grade." (Applause). GENERAL BUSINESS The President: "Are there any matters to raise under this heading? If not, we will proceed to the next item on the agenda which is the presentation of today's paper."

By M. Mpofu, G. Stenzel, F. Magweregwede, B. Maphalala, T. Kgarume

Surface coal operations in which mining activities are conducted above old underground workings experience hot holes after drilling. In a coal mine, hot holes are defined as shot holes, which after being drilled have an in-hole ambient temperature of 40°C or above or show a temperature increase of 3°C or more during monitoring. Hot holes and other cavities, such as cracks, pose health and safety risks to workers, such as exposure to hot air and high concentrations of noxious gases released from these holes. In addition, workers may be exposed to premature detonation of explosives caused by in-hole temperature increases and chemical reactions. To this end, Coaltech Research Association commissioned a project to develop a Best Practice Guideline for the management of hot holes. This paper is a compilation of the activities conducted in the development of the Best Practice Guideline between 2021 and 2022. The activities included a review of standard operating procedures and hot-hole temperature-measuring and -monitoring devices, and the assessment of current hot-hole procedures at selected mines. The results indicated that management of hot holes requires a focus on pre-emptive risk assessment of mining blocks, identification of hot holes using the correct temperature-measuring devices, and continuous monitoring of hot holes from the time of drilling until just before blasting. Hot-hole management accessories, such as polyvinyl chloride sleeves, were found to be effective in insulating the hot-hole emulsion from the rock mass temperature, thus preventing the potential for premature detonation.

Sep 9, 2024

By A. Haque

The shear behaviour of infilled joints produced from ordinary gypsum plaster (gyprock) and bentonite was investigated in the laboratory under Constant Normal Stiffness (CNS) conditions. Shear tests were performed on saw-tooth profiles having Joint Roughness Coefficients (JRC) of 4.75 and 9.25 under an initial normal stress (sno) of 0.30 to 1.10 MPa, and at a normal stiffness (kn) of 8.5 kN/mm. Test data under the same sno and infill thickness to asperity height ratio (t/a) were analysed for two different sets of JRC. The peak shear stress plotted against the t/a ratio under constant sno revealed an increase in peak shear stress with the increase in JRC, up to a t/a ratio of about unity. The effect of roughness on the peak shear stress was observed to be minimal when the t/a ratio exceeded 1.40. A mathematical model for the prediction of peak shear stress due to the increased infill thickness has been developed based on a hyperbolic stress-strain relationship and energy balance principles. The model predictions are in good agreement with the laboratory observations. Le comportement de cisaillement des joints remplis produits à partir de plâtre ordinaire et de bentonite a été étudié dans le laboratoire sous des conditions de rigidité normales constantes. Des essais de cisaillement ont été réalisés sur des profils en dents de scie ayant des coefficients de rugosité des joints (CRJ) variant de 4,75 à 9,25 sous un effort normal initial (sno) de 0,30 à 1,10 MPa, et une rigidité normale (kn) de 8,5 kN/mm. Le résultat des essais conduits sous la même contrainte et épaisseur de remplissage au rapport aspérité/hauteur (t/a) ont été analysés pour deux ensembles différents de CRJ. La variation de l'effort de cisaillement maximal contre le rapport t/a sous une contrainte normale constante a indiqué une augmentation de l'effort de cisaillement maximal avec l'augmentation du CRJ, jusqu'à un rapport de t/a proche de l'unité. L'effet de la rugosité sur l'effort de cisaillement maximal a été minimal quand le rapport t/a a excédé 1,40. Un modèle mathématique pour la prévision de l'effort de cisaillement maximal dû à l'épaisseur accrue du remplissage des joints a été développé sur la base de la variation entre contraintes hyperboliques et déformation et sur des principes de bilan énergétique. Les prévisions du modèle sont en bon accord avec les observations de laboratoire. Das Scherverhalten in mit gewöhnlichem Gips und Bentonit gefüllten Klüften wurde im Labor unter Bedingungen konstanter Normalsteifheit (CNS) untersucht. Scherversuche wurden durchgefürt für Sägezahnprofile mit Werten des Fugenrauhigkeitskoeffizienten (JRC) von 4.75 und 9.25 unter Normalspannungs-werten (sno) von 0.30 bis 1.10 MPa, und bei Normalsteifheit (kn) von 8.5 kN/mm. Testresultate für gleiche Werte von sno und Verhältnis Fülldicke zu Rauhigkeit (t/a) wurden untersucht für zwei verschiedene Werte von JRC. Die Beziehung zwischen maximaler Schubspannung und und t/a Verhältnis unter konstantem sno zeigte einen Anstieg der maximalen Schubspannung mit zunehmendem JRC, bis zu einem t/a Verhältnis von etwa 1.0. Der Einfluss der Rauhigkeit auf den Maximalwert der Schubspannung war minimal solange das t/a Verhältnis den Wert von 1.40 überstieg. Ein mathematisches Modell wurde entwickelt für die Vorhersage der Schubspannung die von zusätzlicher Fülldicke erwartet werden kann, ausgehend von einer hyperbolischen Spannungs-Dehnung Beziehung und dem Energiegleichgewichts-prinzip. Die Modellvorhersagen zeigten gute Uebereinstimmung mit den Laborbeobachtungen.

Jan 1, 2003