Search Documents

By C. S. Kucukkargoz, A. Bhalla

"The solid-state reduction of ilmenite concentrate with graphite was studied under argon atmosphere at temperatures between 1050°C and 1350°C. The rate of reduction increased with increasing temperature and decreasing particle size, with the maximum extent of reduction found to be 80% at 1350oC with a particle size in the range of -106 +90 µm. The activation energy for the reduction reaction was calculated to be 257 kJ/mole. The trivalent iron oxide was reduced first to divalent iron oxide and then to metallic iron. An annular ring of a partially reduced oxide phase containing metallic nuclei was formed around the core of ilmenite, which grew in size as the original ilmenite core shrank with progressive reduction. The reduction of titanium dioxide also took place during this stage, which produced the Magneli oxides in the form of TinO2n-1. The metallic phase had very high Fe and low Ti contents throughout the reduction, whereas the partially reduced oxide phase adjacent to the metallic phase was high in Ti and depleted in Fe. The metallic phase globules formed during this stage were small and are considered suitable only for leaching and not for other concentration processes. The core of the particle generally retained the composition of the original ilmenite. The purpose of this work was to remove iron and increase the titanium oxide content of the ilmenite to produce a high-titanium containing charge for subsequent smelting.IntroductionThe titanium-bearing minerals ilmenite (FeTiO3) and rutile (TiO2) are the primary natural raw materials used in industry to produce titanium metal and titanium-based products. The common titanium-bearing minerals are ilmenite, rutile, anatase, brookite, leucoxene, arizonite, and perovskite. Although the formula of ilmenite is commonly expressed as FeTiO3, the mineral can accommodate Mn and Mg, which are chemically bound in the form of (Fe,Mn,Mg)TiO3. Ilmenite concentrate can also contain Fe2O3 and Al2O3 in addition to the physically separable oxides such as SiO2 and CaO. The crystal structure of ilmenite is an ordered derivative of the corundum structure with a trigonal-rhombohedral symmetry. Fe2+ and Ti4+ ions occupy the octahedral sites, leaving the tetrahedral sites unoccupied. In each FeTiO3 unit, there are three O2- ions creating three octahedral sites, two of which are occupied by Fe2+ and Ti4+ (Wilson et al., 2005)."

Jan 1, 2017

By J. L. Havenga, L. J. van der Walt, J. T. Nel, H. Bissett

"SynopsisNew technologies used to manufacture high-quality components, such as direct laser sintering, require spherical powders of a narrow particle size distribution as this affects the packing density and sintering mechanism. The powder also has to be chemically pure as impurities such as H, O, C, N, and S causes brittleness, influence metal properties such as tensile strength, hardness, and ductility, and also increase surface tension during processing.Two new metal powder processes have been developed over the past few years. Necsa produces zirconium powders via a plasma process for use in the nuclear industry, and the CSIR produces titanium particles for use in the aerospace industry.Spheroidization and densification of these metal powders require remelting of irregular shaped particles at high temperature and solidifying the resulting droplets by rapid quenching. Spherical metal powders can be obtained by various energy-intensive methods such as atomization of molten metal at high temperatures or rotating electrode methods. Rapid heating and cooling, which prevents contamination of the powder by impurities, is, however, difficult when using these methods for highmelting- point metals. For this reason plasma methods should be considered.Thermal plasmas, characterized by their extremely high temperatures (3000–10 000 K) and rapid heating and cooling rates (approx. 106 K/s) under oxidizing, reducing, or inert conditions, are suitable for spheroidization of metal powders with relatively high melting points. Thermal plasmas for this purpose can be produced by direct current (DC) plasma arc torches or radio frequency (RF) inductively coupled discharges. In order to obtain chemically pure spheroidized powder, plasma gases such as N2, H2, O2, and CH4 cannot be considered, while Ar, Ne, and He are suitable. Neon is, however, expensive, while helium ionizes easily and it is therefore difficult to obtain a thermal helium plasma at temperatures higher than 3000 K. Therefore argon should be used as plasma gas. Residence times of particles in the plasma region range from 5–20 ms, but this is usually sufficient as 7–8 ms is required for heating and melting of titanium or zirconium metal particles in the 30 µm size range at 3500 K. In this study the melting and spheriodization of titanium powders was investigated by DC non-transferred arc and RF induction plasma methods. The powders were characterized before and after plasma treatment by optical microscopy and scanning electron microscopy (SEM) to observe if any melting or spheroidization had occurred."

Jan 1, 2015

By S. J. van Wyk, A. S. H. Haagner, A. Abraha

Opencast coal mining is responsible for the greatest area of land disturbance across all of the commodity types in South Africa. Many thousands of hectares have been rehabilitated to date and, although rehabilitation performance is not always measured or reported, a significant database, spanning 24 years, has now been analysed to identify the main shortcomings holding back rehabilitation sustainability across the industry. Data from 48 different collieries with rehabilitation performance scores measured from 2000-2024 were analysed. A standardised assessment framework was implemented at all 48 collieries, focusing on aspects of land capability, soil fertility, landscape form and drainage, vegetation species composition and basal cover, implementation of maintenance programmes, and prevalence of invasive alien plants. The findings show that, although invasive species management, plant species composition, and plant basal cover are often adequate, the implementation of aftercare and maintenance programmes (influencing soil fertility) and deficiencies in overall landform design and drainage systems are most significant in preventing overall rehabilitation progression and self-sustainability. Integrating these during design and rehabilitation execution, followed by intensive maintenance (especially in the first five years post-topsoiling and seeding) will be key for the overall industry performance to improve to acceptable levels. The database is biased towards collieries that actually do undertake rehabilitation and that do measure it, hence the actual industry performance is likely worse than what is presented. Due to the substantial hectarages involved and the main post-mining land uses being grazing and crop production, the industry cannot afford to keep perpetuating deficiencies in achieving the foundational aspects of rehabilitation that would pave the way for sustained economic future use.

Apr 25, 2025

By S. Heukelman

Zincor uses O2 enrichment (up to 26% O2 in the fluidizing air) to increase the processing rate of zinc concentrates in the fluidized bed roasters. The aim of this study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining current roaster feed rates and calcine quality. It was found that, with a load of 20% micro-pellets introduced into the feed blend, that O2 enrichment could be reduced by 60%. It was determined that entrained particles spend on average between 0.46 hour and 2.44 hour in the roaster, compared to particles remaining between 3.93 hour and 4.00 hour in the bed overflow. This compares well with a radioactive tracer test performed by Spira. The required reaction time for micro-pellets was found to be less than the residence time inside a Zincor roaster. The result achieved indicated that the average particle residence time inside the roaster was increased successfully in order to compensate for the longer reaction time required to roast micro-pellets at lower levels of O2 in the fluidizing air.

Jan 1, 2011

By O. A. Olaseinde

The 2101 lean duplex stainless steel has wide potential application in storage, heat exchangers, and in the oil and gas industries. This work investigates the electrochemical behaviour of 2101 duplex stainless steel with an addition of 0.15 wt% ruthenium, using potentiodynamic techniques in 1M H2SO4 at 25º, 40º, 60º, and 80ºC. The microstructures of samples were characterized using optical metallography and scanning electron microscopy. The results showed that the ruthenium addition moved the corrosion potential of alloy 2101 to a more positive potential. All samples containing ruthenium displayed longer passive regions at 25°C and 80°C compared to those without ruthenium. Alloys without ruthenium had higher critical current density (icrit) values when compared to the alloys with ruthenium. Ruthenium additions decreased the passive current densities and inhibited anodic dissolution. At room temperature the corrosion rate of alloys with ruthenium was lower than these without ruthenium.

Jan 1, 2012

The 96th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 11th August, 1993. OBITUARIES The President announced the deaths of the following members of the Institute during the past year. Life Fellow E.F. Laschinger. Other Members R.K. Boright, J.S. Jacobi, R.D. Power, J.H. Cannon, C.J. du Plooy, L.B. Mcrae, C.P. Rossouw, A.L. Sillars, A.W. Heugh, R.K. Briggs, P.J. Stark, and C.S. Stott. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1993

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By A. Navarra, A. Quelopana

The mine production scheduling problem (MPSP) has been studied since the 1960s, and remains an active area of computational research. In extending the concepts of the MPSP, the automated mine may now be regarded as a hierarchical intelligent agent in which the bottom layer consists of distributed robotic equipment, while strategic functionality occupies the higher layers. Here we present a disambiguation of artificial intelligence, machine learning, computational optimization, and automation within the mining context. Specifically, the Q-learning algorithm has been adapted to generate the initial solutions for a high-performing strategic mine planning algorithm, originally developed by Lamghari, Dimitrakopoulos and Ferland, based on the variable neighbourhood descent (VND) metaheuristic. The hierarchical intelligent agent is presented as an integrative conceptual platform, defining the interaction between our new Q-learning adaptation and Lamghari’s VND, and potentially other hierarchically controlled components of an artificially intelligent mine, having various degrees of automation. Sample computations involving Q-learning and VND are presented.

Dec 1, 2021

By R. Rumpold

The platinum group metals (PGMs) palladium, platinum, and rhodium represent the key materials for automotive exhaust gas treatment. Since there are currently no adequate alternatives, the importance of these metals for the automotive industry is steadily rising. The high value of PGMs in spent catalysts justifies their recycling. The state-of the-art technology is to melt the ceramic carrier and collect the precious fraction in a liquid metal bath. As the feed material has quite high melting points, huge amounts of energy are required for this process. Hydrometallurgical treatments of the spent catalysts offer the possibility to recycle the PGMs with less energy and time demands. Moreover, automotive catalysts contain further valuable materials to improve the exhaust gas treatment. These compounds, like cerium oxide, cannot be recovered in pyrometallurgical processes. This paper deals with a special process that uses hydrometallurgical principles to recycle the valuable metal fraction from spent automotive catalytic converters. Hydrochloric acid in combination with hydrogen peroxide is used as leaching agent. This combination selectively dissolves the PGMs and the cerium, which can be recovered in separate steps. As the leaching solution is regenerated and reused, wastewater generation is minimized. Furthermore, the process residues constitute potential byproducts.

Jan 1, 2012

By A. N. Clay, N. N. Moeketsi, S. Joubert

For many years, mine-impacted water has been regarded as a problem and linked to long-term environmental liabilities. However, this water can be a renewable and a sustainable resource, provided that it is managed in a responsible and sensible manner. South Africa’s National Water Resource Strategy (NWRS, 2013) considers water that can be used to contribute to economic activity to be a water resource. Although all water resources are considered as belonging to the State, government does not appear to have meaningfully explored the use of mineimpacted water to contribute to the country’s economic activity. Africa is blessed with more sunshine than anywhere else, apart from Australia, yet we see no rollout of vast quantities of solar panels to ensure every African family has access to affordable power. This suggests that governments are incapable of managing such a free resource. At the same time, apart from the equatorial areas, water is a seriously constrained resource and yet we expect the same entities to manage a commodity none of us can live without. This paper explores the conversion of mine-impacted water from waste to a resource and how the inclusion of other stakeholders (such as water users, landowners, and ordinary South Africans) could benefit the process.

Jan 2, 2022

By P. F. Dicks, N. J. Shackleton, E. H. W. Theron, V. Malysiak

Flotation is a complex physical chemical process in which flotation reagents play a vital role in valuable minerals recovery and concentrate grades. This study examines the performance of new generation AECI Mining Chemicals (previously named Senmin) collectors. They were developed to enhance the valuable minerals recovery and flotation selectivity by tailoring the collectors to target specific valuable mineral species present in an ore and thus create added value for concentrators treating PGM ores. The case study was conducted on a Platreef ore, where batch flotation tests were performed and the concentrates were mineralogically characterised for PGE and BMS using QEMSCAN. Further batch flotation testwork was conducted on Merensky and UG2 ores from various localities in South Africa to confirm the trends observed for Platreef ore. The results have shown that there is a strong correlation between PGE mineral type and AECI Mining Chemicals collector type - clearly demonstrating that one reagent type does not fit all flotation applications. Keywords: Batch flotation, QEMSCAN, collectors, PGE and BMS

Jan 1, 2020

By H. Von Michaelis

The world is rapidly becoming more ?green? i.e. energy conscious. Since mining and mineral processing are massive energy users, the mining industry is seeking ways to reduce its energy footprint. In mining and mineral processing operations, energy is often the most expensive cost item. Comminution, i.e. grinding, is frequently the most energy-intensive step between mine and metal. High pressure grinding rolls (HPGR) are being installed in a rapidly growing number of ?hard rock? mineral processing operations. In the energy conscious cement industry, HPGR grinding has been standard practice for decades. HPGR is known to be energy-efficient; the question is how energy efficient? How can the energy efficiency of HPGR be enhanced? This paper reviews recent HPGR applications for the processing particularly of copper, gold, platinum, PGM-Ni-Cu and iron ores. HPGR technology is discussed with respect to energy efficiency. The harder the ore the greater the energy savings are likely to be. Typical energy savings of 10?20% can be expected when installing HPGR vs. a SAG mill. Wipf(2005) showed why conventional Bond Work index tests on HPGR product is likely to under-estimate the energy savings that can be achieved by installing HPGR. Energy efficiency of HPGR is, however, ore-specific. The biggest energy savings of HPGR tested thus far is 9.5 kWh/tonne claimed for Vista Gold?s Mt. Todd gold ore from Western Australia, a savings of over one-third of conventional SABC comminution energy. Several commercial scale iron-ore pellet feed plants install HPGR for fine-grinding of concentrate to increase the surface area of pellet feed in a manner that reduces overall energy consumption. Energy-consumption in comminution is, however, only part of the energy savings benefit story. HPGR typically also reduces the amount of steel lost through wear of mill liners and media. Marsden(2008) showed that when the energy that would have been consumed to produce the steel that is saved by applying HPGR is factored in, then the overall energy savings of HPGR is considerably greater. Johnson et al.(1988, 2005) tested HPGR in a flowsheet in which energy savings of around 50% can be expected if HPGR product screen oversize is recirculated to the HPGR. Innovative flowsheets have been proposed by Rule et al.(2008) and by Morley (2008) which are expected to result in significantly increased energy savings. HPGR applied in flowsheets in conjunction with coarse ore separation devices, e.g. ore sorting or DMS to remove barren waste from HPGR feed promises significantly greater energy efficiencies. Fine-grinding and ultra-fine grinding of ore or concentrates in conventional ball mills results in energy consumptions that increase exponentially with product fineness. Wipf (2009) presented a flowsheet in which he proposed the installation of HPGR ahead of the Aerosion ?Disintegrator? for ultra-fine grinding of ores and/or concentrates. This dry grinding arrangement is expected to achieve ap80 = 7 µm using up to 100 kWh/t less energy than could be achieved by wet ball milling. Using conventional comminution, an ore might require grinding to p80 = 45µm (? 325 mesh), for example, to liberate the valuable components, e.g. magnetite, from gangue, e.g. silica. Inter-particle comminution in HPGR may break some ores along grain boundaries thereby liberating valuable minerals from gangue at a much coarser particle sizes. Early magnetic separation rejection of silica gangue liberated from magnetite by HPGR at coarser grain sizes could further reduce downstream comminution energy consumption.

Jan 1, 2009

By G. Chitiyo

Prediction of pothole characteristics is a challenging task, confronting production geologists at the platinum mines of the Bushveld Complex. The frequency, distribution, size, shape, severity and relationship (FDS3R) of potholes has a huge impact on mine planning and scheduling, and consequently cost. It is with this in mind that this study was initiated. Quantitative analysis of potholes indicates that pothole size (area covered) can be described by two partly overlapping lognormal distributions. These are referred to as Populations A (smaller) and B (larger). The range of observed pothole sizes conforms to a simple double exponential growth model based on Newton's Cooling Curve. A third size range of very large potholes (Population C) that could not be modelled properly within the proposed growth model is interpreted as to represent a very early phase of aggressive regional thermo-chemical erosion and potholing. In general, potholes are dominantly quasi circular with only a subordinate tendency of elongation. In the UG2, potholes with elongated forms are more prevalent in the size range between 20 and 500 m diameter. In the Merensky Reef elongated potholes are more common in the size range above 50 m in diameter. Although not distinctly visible, elongation of potholes in both the UG2 and the Merensky Reef show a net north/south orientation. Using shapes of pothole rims and floor areas, documented for the UG2 in the Waterval Shaft area, it is demonstrated that the northern, down-dip edges of potholes have steeper dips than the southern, up-dip edges. Spatial distribution studies using a uniform quadrant method suggest that in both the UG2 and the Merensky Reef, the potholes are randomly distributed, with a tendency towards clustering. Clustering appears to be more prevalent in the smaller Population A potholes. Bearing all findings in mind, it is found that the model of thermo-chemical erosion of the cumulus floor by new influxes of superheated magma best explains the observed data. Partial to complete melting of the cumulate floor occurred in three phases. The first represents the emplacement of hot magma. This magma, due to turbulent flow and high chemical and physical potential, aggressively attacks the existing floor (crystal mush on the magma/floor interface). Regional erosion is manifested by large, often coalescing potholes. During the second phase, when the magma emplacement process ceased and cooling in situ started, two distinct periods of pothole formation ensued. The first is related to rapid cooling along the relatively steep part of the Newton Cooling Curve, when Population B potholes nucleated randomly and grew rapidly with concurrent convective overturn and largely laminar flow condition. The second period of cooling occurred on the shallow-dipping part of the Newton Cooling Curve. Population A pothole growth became more subdued and nucleation appears to have been, at least locally, clustered. The final phase of this proposed 'super magma cycle' was introduced when chromitite crystallization and precipitation terminated pothole formation. This was followed sequentially by pyroxene and plagioclase crystallization to form the typical cyclic units of the Critical Zone. No suitable proxy could be found for the prediction of pothole density of potholes associated with the UG2 (likely due to limited spatial data coverage), and these are best predicted by extrapolation. The Merensky Reef slope index, in contrast, provides a proxy for pothole density, enabling prediction with reasonable confidence. This predictive model has been verified using underground information. The findings made during the course of this investigation have, when implemented, significant impact. Successful implementation will not only allow enhanced resource and reserve definition, but also better mine planning and scheduling.

Jan 1, 2008

By J. Moema, L. Mampuru, M. Phasha, D. Mkhonto

The global liquified natural gas (LNG) storage market size is projected to reach USD17.5 billion by 2025. Currently, owed to its high toughness, tensile strength, and excellent weldability, the 9% nickel steel is the most used in building infrastructure for cryogenic applications such as the construction of tanks and pipes for storage and transportation of LNG. However, this alloy is not readily available because of its complex production process and high cost. This provides an opportunity for suitable alternative materials to build infrastructure for cryogenic applications. Among strong contenders is the Fe-Mn based alloys, which have sparked global interest due to their desirable properties such as relatively lower density, low cost, high toughness and strength, due to a high manganese (Mn) content. These attractive properties render Fe-Mn based alloys preferred candidates to replace traditional steels in engineering applications in which strengthweight ratio is critical. In response, as a build-up to designing and developing austenitic Fe- Mn alloys, the present study employed density functional theory (DFT) based first-principles computational materials modelling technique to investigate the structural, thermodynamic, and magnetic properties of binary Fe-Mn alloy composition in competing FCC, HCP, and BCC crystal structures. Using this approach, it was possible to unravel the key underlying elastic properties that are directly correlated to experimental tensile strength and high toughness in binary Fe-Mn alloys. Besides successfully validating the existing experimental data, the current predicted properties and the deployed approach will serve as a benchmark from which further alloying required to improve other properties will be conducted.

Mar 4, 2025

By S. Swanepoel, A. V. Cherkaev, Q. G. Reynolds, M. Erwee

Ferrochrome (FeCr) is a vital ingredient in stainless steel production and is commonly produced by smelting chromite ores in submerged arc furnaces. Silicon (Si) is a componrnt of the FeCr alloy from the smelting process. Being both a contaminant and an indicator of the state of the process, its content needs to be kept within a narrow range. The complex chemistry of the smelting process and interactions between various factors make Si prediction by fundamental models infeasible. A data-driven approach offers an alternative by formulating the model based on historical data. This paper presents a systematic development of a data-driven model for predicting Si content. The model includes dimensionality reduction, regularized linear regression, and a boosting method to reduce the variability of the linear model residuals. It shows a good performance on testing data (R2 = 0.63). The most significant predictors, as determined by linear model analysis and permutation testing, are previous Si content, carbon and titanium in the alloy, calcium oxide in the slag, resistance between electrodes, and electrode slips. Further analysis using thermodynamic data and models, links these predictors to electrode control and slag chemistry. This analysis lays the foundation for implementing Si content control on a ferrochrome smelter.

Mar 14, 2024

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By A. S. Geldenhuys, L. S. Leal Filho, D. A. Deglon, T. C. Souza Pinto

The Brucutu iron ore mine (Minas Gerais, Brazil), is Vale`s largest iron producing operation achieving around 21 million tons by flotation of iron ore pellet feed per annum. The run of mine is mainly composed of hematite (70%) and quartz (30%). After preparation (comminution and sizing), the slurry is submitted to reverse cationic flotation of quartz under basic conditions (pH=10.5). Corn starch (500g/t) is used to depress Fe-bearing minerals and alkyl (C10) ether amine is the collector for quartz. The flotation circuit is arranged in a “coarse” section utilizing dated 28m3 square Wemco cells, and a “fine” section utilizing modern 160m3 tank cells. The “coarse” flotation circuit treats material from the deslime cyclone underflow while the “fine” circuit treats material from the deslime cyclone overflow and the pulp product from the “coarse” circuit scavenger 2 bank. Evaluation of process performance is of high importance as even small gains can lead to large improvements for this high throughput plant. Cell-by-cell samples of the froth products, selected feed and pulp-products were analyzed for flow-rate, overall chemical composition, and particle size distribution. Bank-by-bank samples of the feed, froth and pulp products were analyzed on an assay-by-size basis. In addition, the flotation cells were hydrodynamically characterized and gas dispersion parameters assessed. The detailed experimental program resulted in a thorough characterization of the process and enough information to produce a calibrated floatability component model. Longer mainline residence time results in significant Fe2O3 losses while yielding little benefit in terms of SiO2 grade. Scavenger 2 has twice the residence time of scavenger 1 while having to treat only 10% of the SiO2; resulting in high Fe2O3 recoveries to the froth and poor separation. In addition, it is shown that the Fe2O3 exhibits true flotation behavior resulting in increased Fe2O3 losses. The detailed data collection campaign coupled with in depth data analysis and modelling gives unprecedented information and highlights avenues for optimization that was previously unknown. Keywords: Froth Flotation, Process modelling, Process evaluation, Metallurgical survey

Jan 1, 2020

By T. R. Marshall

SAMREC (The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves) Clause 7 notes that ‘Documentation detailing Exploration Results, Mineral Resources and Mineral Reserves from which a Public Report is prepared must be prepared by, or under the direction of, and signed by a Competent Person.’ Similar statements with respect to Competent Valuators (CVs) and Qualified Reserves Evaluators (QREs) are contained in the SAMVAL (South African Code for the Reporting of Mineral Asset Valuations) and SAMOG (South African Code for the Reporting of Oil & Gas Resources) codes respectively. What does it mean to be a Competent Person (CP) in the context of compiling/signing-off on SAMCODE (South African Mineral Code) compliant documents? What do the registration and experience requirements mean? Who is ultimately responsible for the report and what does such responsibility prescribe?

Sep 1, 2021

By S. T. L. Harrison, M. Smart, C. J. Edward

Biooxidation, a biohydrometallurgical process, utilizes a mixed microbial consortium to mediate the dissolution of refractory gold-bearing ores to enhance gold recovery during cyanidation. Recognition of water as a critical resource has prompted improved water management strategies within mining and minerals processing. Bioremediated wastewater from the cyanidation tailings provides a potential water source to supplement the water required for the biooxidation circuit, reducing freshwater extraction. Gold biomining operations have typically been reluctant to recycle this wastewater due to the potential inhibitory effects of cyanide and thiocyanate (SCN-) on the microbial population. Historical process upsets suggest that the microorganisms are sensitive to SCN- concentrations as low as 1 mg/L. However, effective bioremediation processes resulting in effluents with low or negligible SCN- concentrations may allow gold biomining plants the opportunity to recycle available water. Microbial activity as well as alteration in community structure were monitored as a function of increasing SCN- concentration over the range of 0 mg/L to 5 mg/L to investigate the response of the biooxidation community to potential SCN- spikes resulting from upsets in the remediation process. Appropriate microbial growth and ferrous iron oxidation activity with a nominal shift in community structure were observed at SCN- concentrations up to 1 mg/L. Thiocyanate concentrations above 1 mg/L resulted in the complete inhibition of ferrous iron oxidation activity. This was attributed to Leptospirillum ferriphilum’s sensitivity to SCN-. Exposure to a SCN- concentration of 5 mg/L resulted in a lower cell concentration and a significant increase in growth lag time, and the absence of L. ferriphilum from the microbial population. At. caldus and Ap. cupricumulans were still present at 5 mg/L SCN-, although Ap. cupricumulans was unable to oxidise ferrous iron at this SCN- concentration. It was concluded that recycling bioremediated cyanidation tailings wastewater within the biooxidation circuit is feasible; however, to retain process performance, SCN- concentrations should not exceed 1 mg/L. Keywords: Biooxidation, thiocyanate, water recycling, community structure

Jan 1, 2020