Search Documents

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By Glenn A. Hazen

This report presents a stress investigation of four coal pillars located under two depths of cover. Each coal pillar was instrumented with ten load cells designed to measure coal pressure during initial and secondary mining. The problem considered was one of uniform triaxial stress as a large coal pillar was loaded under a thick limestone bed. Special attention was given to pillar design procedure. Unconfined uniaxial compression tests were conducted for coal specimens 7/8 in., 2-1/8 in., 3 in., and 4 in. square with length to square side ratios of 1/2, 1, 1-1/2, and 2. Stress-strain curves were recorded. Six specimens were tested at each size. Results show that a coal pillar is composed of an inner zone which is highly loaded plus a region around its perimeter which has lost its elastic strength. The bearing capacity of a coal pillar consists of elastic and crushed coal response: The failure strengths have been determined and will be useful in coal recovery, mine design, and mine safety.

Jan 1, 1975

By C. H. Fisher, M. L. Fein, A. Eisner, G. C. Sprunk, Loyal Clarke, H. H. Storch

"The large reserves of low-rank coals in the western United States are at a disadvantage in competing with the more mature but less plentiful eastern coals, which are nearer important markets and are more suitable for combustion and coke production. However, low-rank coals generally are amenable to hydrogenation, and the western coals might become an important source of liquid fuels and organic chemicals when petroleum is less plentiful.In view of these facts an the tremendous quantities available, further information on the western coals clearly desirable. The purpose of the work described in this paper was to study the hydrogenation characteristics of some of the low-rank western coals in discontinuous converters. The data obtained in this manner, which are inadequate for predicting the suitability of coals for large-scale continuous hydrogenation, were used as a basis for selecting samples for further study in the Bureau's experimental coal-hydrogenation plant (26, 35). 8/ Because of the general importance of the western coals and recently demonstrated relation between coal hydrogenation and petrograghy (14, 15, 16), the proportions of anthraxylon, (vitrain), translucent attritus, and opaque matter were determined. In some instances samples of anthraxylon were isolated and hydrogenated separately so that their properties might be compared with those of the entire coal. The samples studied include peat, brown coal, lignite, sub-bituminous coals, and low-rank bituminous coals."

Mar 1, 1940

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

By Richard W. Lusignea

This report describes a program to evaluate the feasibility of determining roof features which occur in United States coal mines from changes in bolting machine drilling parameters. The ultimate purpose of this effort is the development of an instrumented roof bolting machine which can detect hazardous roof conditions and/or indicate when the existing roof control plan is inadequate. A survey of hazardous conditions occurring in United States coal mines is included, along with the slang expressions for these conditions, and their relative degree of hazard. Specific machine parameters are identified for detecting the specific roof conditions. Measurement concepts are proposed using readily available instrumentation in most cases. Various systems are evaluated and tradeoffs presented. An implementation plan is proposed for developing a prototype system and using it in an operating coal mine.

Jan 1, 1978

By E. P. Carman

1. CARMAN, EVERETT P., OPPERMAN, MARTHA, NISHIYANA, SALLY, AND RACOOSIN, LEE. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1945 to 1950. B. 528, 1954, 60 pp. 40 cents. 2. ROSE, HAROLD J. Industry-Sponsored Coal Research in the United States. Chap. in Proceedings: Fifth International Conference of Directors of Mine Safety Research. B. 489, 1950, pp. 9-12. $1.25. Minerals Yearbook 3. STRINER, HERBERT E., CARMAN, E. P., AND GOODING, RICHARD M. Review of the Mineral-Fuel Industries in 1952. Minerals Yearbook 1952, Fuels, vol. 2 (pub. 1954), pp. 1-28.

Jan 1, 1958

By Manuel Gomez

Low-temperature carbonization product yields for 129 coals representative of 12 Utah coalfields were estimated, using regression equations developed from heating value and proximate and ultimate analysis data. It was shown that yields of char, tar plus light oil, water of decomposition, and gas, as well as the gas volume and the heating value of the gas, could be predicted with reasonable accuracy. Published and experimental results from eight Utah coals carbonized at selected temperatures in the 4500 to 1,000° C range were used to determine the effect of temperature on product yields. Carbonization temperature, heating value) oxygen, and volatile matter of coal appear to be the principal variables influencing carbonization product yields. Data presented show that the heating value and the residual volatile matter in low-temperature char may be predicted using relationships developed from proximate analysis data for 220 coals.

Jan 1, 1967

The Bureau of Mines is active in programs pertaining to solid waste disposal and land reclamation. Nine reclamation projects of mining companies and six projects of the Commonwealth of Pennsylvania were investigated to provide information on the procedures, costs, and results obtained from reclamation projects of bituminous coal-waste disposal areas. Refuse disposal costs of mining companies ranged from 9 to 28 cents per ton-mile, and quantities disposed of ranged from 600 to 4,500 tons per day. Spreading and compacting the refuse at the dump site ranged from 3 to 20 cents per ton. Cost of covering with soil and planting ranged from $750 to $1,646 per acre. Total costs of reclamation for the Pennsylvania projects ranged from about $1,800 to more than $15,000 per acre. Refuse preparation costs ranged from $772 to $5,550 per acre. Soil covering and planting costs ranged from $1,083 to $5,086 per acre. The best results were obtained by soil preparation and conditioning prior to planting. The type and depth of soil and effect of climate were also factors.

Jan 1, 1973

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By Joseph M. Kurtak

The Bureau of Mines conducted a four year (1985-1988) mineral assessment of the Juneau Mining District in southeast Alaska as part of its ongoing statewide mining district evaluation program. Following an extensive literature search, the Bureau investigated mines, prospects, and mineral occurrences in the area. This report describes the results of Bureau work in the Eagle River area of the Juneau gold belt; a component of the Juneau Mining District comprising 87,000 acres between the Mendenhall Glacier and Berners Bay. Gold and silver have been the only metals having significant production from the area and occur mainly in quartz stringer and fissure type veins hosted by phyllites, greenschists, greenstones, altered diorite dikes and quartz diorite gneiss. Gold also occurs in several small placer deposits. Approximately 21,100 oz of gold and nearly 9,000 oz of silver were produced over a 60 year period. Currently, the only mining activity consists of some exploration and minor placer gold production. Inferred and indicated lode gold resources having mineral development potential total approximately 796,000 tons with a weighted average grade of 0.22 oz/ton gold.

Jan 1, 2011

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By Oliver Bowles

"Asbestos" is a name applied to a group of naturally fibrous minerals. Because it has the fibrous characteristics of silk or cotton and at the same time will not burn and has other advantageous properties as well, asbestos has specialized uses for which no adequate substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products, the manufacture of which constitutes a vast industry. Asbestos generally occurs in irregular veins scattered throughout rock masses. Most of the fiber-bearing rock is mined in huge open-pit or underground workings. The fibers are separated from the rock and sorted into groups, according to length, in large, complex mills. The longer fibers are stripped to textile plants, where they are further fiberized and prepared in special machines and are used for spinning into yarn and weaving into unburnable cloth that has many important uses. The shorter fibers, which are much more abundant than the long ones, are used in asbestos-cement building materials in heat-insulating products and for a multitude of other applications. These processes and uses are covered in considerable detail in later sections of this report.

Jan 1, 1959

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d'Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978