Search Documents

By Jonathan Peck, Doug Pollitt, Malcolm Scoble

Over the past 5 years the Department of Mining and Metallurgical Engineering, McGill University, has been involved in the performance monitoring of both percussive and rotary drills. Studies conducted in open pit coal and iron ore mines using microprocessor-based research and commercially available instrumentation resulted in the monitoring of at least 6 performance parameters while drilling vertical production blastholes.

Jan 1, 1991

By Corry Goumans, Dwayne Wallace

"On July 1, 1997, a rockslide occurred on the I-40 in Hayward County, North Carolina that completelyblocked all lanes and disrupted traffic flow in the region. Remedial measures were undertakenimmediately in order to open traffic, however on-going geotechnical investigation revealed stabilityconcerns that necessitated closing the highway to ensure public safety. Access to the top of the slope was available only from the bottom of the slide on the Interstate I-40. Excavation and trim blasting started from the top and along the west slope of the failure, however, additional geotechnical evaluation indicated that slope stability remedial measures were required to support the western rock slope mass."

Jan 1, 1999

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

By Agne Rustan

The 9th International Symposium on Rock Fragmentation by Blasting was held in the Granada Conference Centre, Granada, Spain from the 14th - 17th September 2009. The Symposium was preceded by a 1 ½ day Workshop on “Vibrations from Blasting” organized by the initiator Dr. Alex Spathis and his colleague M. J. Noy, both employed at Orica Mining, Australia. Prof. Josè Sanchidrian at the “Universidad Politécnic de Madrid” in Madrid, Spain was the main organizer for both the Workshop and the Symposium. A record number of participants came (292) from a record number of countries (41). There were a total of 14 papers in the Vibrations from Blasting Seminar and 96 papers and 2 Keynote Addresses in the Fragblast 9 Symposium itself. The aim with this paper is to present some results from Fragblast 9 which are of interest for a large target group. One very important result from the Fragblast 9 meeting was that it was decided there that Fragblast 10 will be held in November 2012 New Delhi India.

Jan 1, 2009

By William Stewart

Recitations were taking place in the red schoolhouse at Orneville, Maine. It was winter and the snow lay deep on the ground, but some of the scholars were in bare feet, and only half as many hats hung on the pegs as there were potential wearers in the seats. That was forty years ago; and the pioneers of northern New England were more noted for their industry than for their possession of the fruits of it.

Jan 1, 2007

By Joseph Daly

This is the detailed evaluation of the establishment and implementation of an ‘oil recycle plant’ located on site at Boggabri Mine NSW, (Australia); its production, its use and its value. Also discussed in detail is the quality of the raw material produced, and the process and initial application of this raw material generated as well as the analysis of such, as a component within bulk explosive as applied to the mining industry as compiled during analysis. Laboratory analysis prior to field testing is also discussed including independent external laboratory analysis as well as the environmental benefits and a business case for recycled oil in blasting. This paper includes technical details of the product including densities, velocity of detonation and other associated key performance indicators. The intention is to off-set the amount of Distillate (Diesel) utilised as a component of bulk explosives, with a raw recycled oil and thus reducing both the environmental carbon footprint as well as production costs with regard to introduced petrochemical production and utilisation; an oil that is an existing recourse of controlled waste not only difficult but expensive to otherwise dispose of, whilst keeping the entire process ‘on-site’. Though recycled oil in blasting is not an entirely original idea, the key feature of this paper is the ability to complete the entire process on-site.

Jan 1, 2014

By Nikolaos Petropoulos, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature. In this study, pure emulsion was tested in confined conditions to better simulate the behavior of the detonation of the explosive in rock mass conditions. A methodology is proposed for carrying out the evaluation of the explosive performance. The blasthole diameter of the samples varied from Ø 25 mm (0.98 in) up to Ø 65 mm (2.55 in). The confiner was a magnetic mortar cylindrical sample with mechanical properties similar to a rock mass. A streak camera and VoD probes were used to measure detonation front curvature and VoD. The data was analyzed and correlated with the physical parameters of the explosive. Additional to this, the data was further used to calibrate numerical models in LS-Dyna.

While ring-blasting techniques offer substantial benefits, there are intrinsic problems that are exacerbated when large blocks of ore are mined in attempts to improve the production economics. These problems relate to both the convergence of holes around the ring drive and the charging of up-holes. The size and shape of the ore block concerned should be carefully considered so that good drilling, patterns can be achieved. The hole diameters chosen, both affect and are affected by the size of the ore block. The explosive selected depends on the hole diameter and together with the diameter, determines the nominal drilling pattern. Ring-drilling patterns are best derived through the use of computer software together with engineering judgement. The loading of explosive is necessarily high, and charging patterns require careful thought if overcharging is to he minimised and adequate energy is to be available at all parts of the ore block. Initiation systems are critical to the blasting results, but sub-optimal systems must be adopted if collar priming is practised. In view of all these factors, idealised guidelines can be given for ring design, but it should be recognised that developments in technology may in time change some of these parameters.

Jan 1, 2000

This paper is concerned with the blasting of rock in mining. The most common purpose of blasting rock is to cast it or to disrupt its structure sufficiently for effective digging and subsequent removal.

Jan 1, 1991

By Alastair Grogan, Ron Elliott, Dale MacLean

Blasting for armour stone presents many unique challenges. Often, blasters get themselves into trouble when they assume that they can simply modify a production blast design to produce the required fragmentation size. They bid on the project using typical production blasting costs, and then find that they cannot produce the required fragmentation size and quantity with an acceptable waste factor. This paper outlines industry best practice guidelines for the production of riprap or armour stone. The paper examines the importance of initial geological mapping to determine the average in-situ block size, and the advantages to be gained from working with the geology to maximize production of the required block sizes. The paper also outlines the importance of proper explosives selection as well as blast designs that are unique to the production of riprap. The paper reviews challenges and experiences realized from multiple projects in differing rock types.

By David Sprott, Patrick Andrieux

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commercial computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1991

By P D. Katsabanis

According to Persson(1) steady state detonation along a cylindrical charge can be regarded as a self propagating process in which the axial compressive effect of the shock front discontinuity changes the state of the explosive so that exothermic reaction sets in with the requisite velocity.

Jan 1, 1989

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By Michael Wieland

For shooting rock properly, some relatively fixed quantity of rock work is required from the total charge mass, while keeping the overall toxic fumes to a minimum. The overall fumes weighted for the toxicity of different species and taken per unit charge mass, ??, are represented by a relative fume toxicity (RFT) formula. The worst two contributions are often carbon monoxide {CO} and total nitrogen oxides {NOX}, so the traditional Russian formula RFT-R formula suffices, though a generalized form RFT-G with more terms is worth checking. Using the work-principle model from thermodynamics, the rock work per unit charge mass, ??, is found from the reduction in internal energy for the reaction zone. This resolution technique for rock-work invokes the usual assumption that the quick irreversible process occurs without notable heat transfer to the rock (adiabatic); rock-work is not resolved, when this restriction is untenable. The ratio of ?? to ?? yields the weighted toxic fumes divided by the rock work or the readjusted fume toxicity ??, where ?? = ??/??. For convenience, graphical trends of ??, ?? and ?? were normalized using reference results for a stoichiometric (ANFO) mixture of ammonium nitrate (AN) and fuel oil (FO) shot under nominal rock confinement, noted later.

Jan 1, 2006

By Douglas Rudenko

Most engineers, mine operators, or contractors acknowledge the importance of having accurate subsurface information in order to plan a project or solve a problem. Conventional methods of exploring the subsurface such as augering, core borings, or test pits can provide information, but it is often costly and sparse. Geophysical methods offer an alternative to help supplement sparse information~ gathered through conventional exploration techniques.

Jan 1, 1998

By Taner Sumer, H Altay Guvenir

Fragmentation in rock quarries is tried to be achieved by changing the specific charge, drill pattern and bore hole diameters by different experts. This paper is a brief summary consisting of the utilization of practical experiences of the other group on cost optimization procedure that takes into account blasting, transportation and crushing as a whole process and optimize the cost by defining the optimum gelatin based explosives to be used as a main primer of anfo in three different limestone and granite quarries, with similar rock characteristics.

Jan 1, 1993

By Karl E. Burgher

Since World War II, the need for the use of explosives with testing, construction, demolition, mining and quarrying near urban areas has increased dramatically. Once remote, testing areas have been encroached upon by commercial and residential areas. Evidence has been found that overpressure levels near these areas can be estimated using meteorological conditions. This paper reviews a study where 205 test shots were fired, meteorological conditions recorded, and over-pressure levels estimated using multiple regression techniques.

Jan 1, 1988

By Brian T. Burch, Paul N. Worsey

When fired, submerged Linear Shaped Charges (LSCs) lose all effectiveness in the cutting of steel. Users in underwater applications have reported having to substantially increase the charge size to the point where brute explosive force shears rather than cuts the target.

Jan 1, 2015

By Randall S. Marks

Bonneville Dam, completed in 1938, included the smallest and busiest lock on the Columbia and Snake River Navigation System. To expedite barge traffic through this restriction, a new larger lock was designed and contracted by the U.S. Army Corp of Engineers.

Jan 1, 1997

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995