Search Documents

By Albert G. Funk, Gary M. Thornley

The available energy of aluminized ANFO and aluminized slurry blasting agents has been measured by seismic methods, calculated theoretically, and compared. With aluminized ANFO it is concluded that aluminum concentrations should be restricted to less than 10 percent because of diminished energy yields at high aluminum concentrations. However, with aluminized slurry it is concluded that efficient use of aluminum can be made at aluminum concert"rations up to 18 percent. It is further concluded that the difference in efficiency of use of aluminum by these two classes of blasting agents results from a higher contribution to useful work from the condensed detonation products of the relatively higher density aluminized slurry blasting agent.

Jan 1, 1981

By Eddie L. Catbagan

The Escalante silver-bearing deposit, consisting of a relatively wide and continuous quartz vein, contains openings ranging from minute to a few feet wide on the footwall and hanging wall. These openings (water courses or vug holes) are I believed to have been created by the fluctuation of the water table.

Jan 1, 1983

By Stephan Iversan, Janae Singer

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in rock. Excavation blast damage can be as shallow as 1 to 2m (3 to 7ft) and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m (0.8 to 1.6ft) along mine walls. The resulting tomograms of P-wave velocity show low velocity zones which we interpret as residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock.

Jan 1, 2009

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

Active avalanche control is the intentional triggering of avalanches while people are kept out of the hazard area. Explosives are frequently the most effective tool for triggering avalances. In a highway setting an avalanche control program will reduce total highway closure time, while providing greater safety to motorists and maintenance personnel. Avalanche control with explosives is effective when the snow is somewhat unstable and almost ready to slide naturally. Forecasting this condition involves having a network of local meteorological stations, examining snow structure, using mountain weather forecasts, doing snow strength tests, and having the results of ski and explosive tests. The method of delivery of explosives to an avalanche starting zone is governed by the accessibility of the starting zone. Common methods include; hand placing or throwing charges, remote delivery cableways, or "trams", surplus military weapons, and a compressed gas charge launcher, or "Avalauncher". Charges dropped from helicopters are also occasionally use. We have increased the effectiveness of our program by use of large elevated charges. Efforts are being made around the world to develop and utilize better methods for the safe, remote initiation, but procedures have varied dramatically between individual control programs. There is now a movement to review and standardize operational guidelines for avalanche control. Highway avalanche control is often done at night, during winter mountain storms. Heavy rain or snow, high winds, and high avalanche hazard, are common work site conditions. Commercial and economic pressures are increading, so methods that redice highway closure time are important. There are also many safety issues to be addressed in avalanche control work.

Jan 1, 2002

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall.

Jan 1, 1977

By Winfried Rosenstock

AEBT has been available for a couple of years and is successfully applied in Australia. Up to now it was mainly used in coal surface mining at the Australian East- Coast. Presently, the proved results reach ~ 50 % reduction of Drilling & Blasting costs and a productivity increase of between 10 and 20 %. In 2003 it was for the first time used in surface metal-mining. The mine features for the time being an extremely difficult geological environment and had above to be carried out in the transition level waste/ore. Reductions of wall control, powder factor and vibrations were the main target.

Jan 1, 2004

By Gungor Tuncer, Ali Kahriman

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 2 different types vibration monitors (1 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2006

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By William A. Travnik

For more than 60 years, ESSO RESOURCES CANADA LIMITED has been producing and refining oil at a small refinery in Norman Wells, Northwest Territories, and supplying diesel fuel and other oil products to northern markets. In 1982,ESSOwas granted governmental approval to expend production from the oil field from 475 cubic metres a day to 4400 cubic metres a day. This $800,000,000projectproceeded ahead of schedule for a start up in 1985.

Jan 1, 1986

By Albert van Niekerk, Mick Lownds

Overview of the UNI Tronic™ Electronic Blasting System

Jan 1, 2004

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

By Robert Hopler

Torpedoing Wells. – On the completion of the drilling, or when the production is found to decrease, it is usual to “torpedo” the well to increase the flow. This process was patented in 1862 by Colonel Roberts, who believed, with many others, that the oil was contained in crevices in the rock, which might not have been tapped by the bore-hole. He therefore proposed the use of nitroglycerine, gunpowder, or other explosive, to break up the rock at the bottom of the well, so that these rich “pockets” might be brought into communication with the well.

Jan 1, 2007

By Zhao Jie, Christopher G. Smith

Commercial explosive use in China has been dominated by powdered AN-TNT mixes. Water gels and emulsions are now gaining market acceptance because they offer potential for better performance. Although raw material costs for emulsions initially may be more than AN-TNT mixes, the more expensive technology improves sensitization and leads to lower costs overall for mining operations. A recently completed study in northeast China compared microsphere-modified emulsions to AN-TNT and lower-cost emulsions. Testing of microsphere-modified emulsions at several pH levels indicated a high degree of stability and consistency of VOD. Using 42 mm blastholes in underground mines and 170 mm holes in sandstone open pit mining demonstrated the superior performance of glass microsphere sensitized emulsions. Comparisons of explosive cost, drilling cost, secondary blasting cost and muck pile profile were favorable to the microspheres-sensitized-emulsions. Noxious fumes with AN-TNT or with water-based systems that partially fail during detonation are also a concern. Efficient detonation of emulsion products sensitized with hollow spheres appears to reduce fume generation. Prolonged storage or exposure to water also is not a problem.

Jan 1, 1997

By Wm. Reisz, Raphael Trousselle

We are now well into our second decade of commercially available electronic initiation systems. Over this time, the technological advances have made electronic systems a very practical option for a wide variety of blasting applications.

Jan 1, 2011

By Raymond H. Green, Mitchell W. Green

The authors examined the application of precise millisecond delay electric blasting at a well-known Vermont quarry. The paper explains how the use of a new high-accuracy electric delay detonator has improved fragmentation, raised productivity 10%, simplified blast design, and increased the ability to predict results from blasting.

Jan 1, 1986