Search Documents

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By Sathyaprasad Nanjundaiah

The Paper intends to showcase a framework for spatial data collaboration from multiple sources of data, in order to create a single source of truth across the Organization. The framework is targeted to reduce the data duplicity, re-work, time loss due to search of required data and hindrances to fetch or transfer data from various data sources. The spatial data collaboration will provide a single window view of the entire organization with respect to its operations, management, sales, customers and competitors on a spatial reference across various regions in the World. Large Organizations with cross-country operations can standardize the use of spatial data through this framework for ease of data access, increasing the data reliability / integrity and better / on time decision making. Keywords: spatial data, GIS, collaboration, framework, mining, ESRI, tab files, shape files, ETL, reliability, integrity, interoperability, geo data, geo database, single source of truth

Sep 1, 2012

By B. Csoke

The Bond and the Hardgrove methods are widely used for the determination of the material?s grindability. Generally, the determination of the Bond work index of inhomogeneous materials can be carried out with high deviation using the conventional apparatuses and methods, because of the highly different grindability of components. This is more significant when the composite cement?s grindability is measured, which highly affects the design and operation of cement grinding mills. A possible solution can be the combined application of the Bond-method with the determination of the component?s weight ratio in the product and perform the Bond measurement until the steady state conditions of grindability coefficient (G) and chemical composition of the components are reached. To prove the applicability of the above mentioned idea systematic Bond and Hardgrove grindability tests were carried out of two phase composite materials. The experimental results showed that the application of the combined procedure is proven in order to have a more accurate and reliable calculation of the Bond work index of composite materials, especially when the components have significant difference in the grindability and concentration. The measurements also showed the possibilities and limits of the grindability test methods.

Sep 1, 2012

By Kozlov Andrey, Matveeva Tamara

"The results of mineralogical and technological studies of platiniferous dunites from Svetloborsky zonal massif (Urals platinum belt) are presented and the basic typomorphic signs of productive mineral assemblages are substantiated. The characteristic features of platinum ore mineralization are revealed: a wide range of iron-platinum alloys, enrichment of ore-formed system by the elements Os, Ir, Rh and activity of the S and As in it, intrusion of Fe-Ni sulfides in platinum and its fusion with magnetite. More than 80% of PGM mineral grains has size less than 100 microns, that determines the possibility of significant losses of platinum in the process of gravity separation and the need for additional recovery processes for small and fine fractions of platinum tailings and sludge products. Summarized results of laboratory tests of small-volume sample processing of platiniferous dunites are presented and the processing flow sheet is developed and tested. The flow sheet incorporates several stages, including stage-wise grinding and gravity separation of ore using the centrifugal concentrator Knelson KS-MD for differently sized material and flotation treatment of tailing products using new classes of reagents for additional recovery of PGM fines."

Jan 1, 2014

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system's power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

By G. Unland

The sizing of crushers depends on the expected crushing forces. However, the crushing forces develop differently with every individual rock while it is compressed by the working surfaces of the crusher. For sizing, this compression process has to be characterized by the maximum crushing force. The maximum crushing force depends on the strength, shape and size of the rock, the amount and velocity of the imposed displacement of the working surfaces of the crusher on the rock and the conditions of the contact surfaces. From experience it is known that the strength of the material and, therefore, the crushing forces depend on the size of the specimen. This dependence is the so called size effect. The determination is based on compression tests. The force development is recorded during the compression of the specimen and for every individual test the maximum force is determined. The occurring maximum crushing forces of several rocks with the same diameter comminuted under the same conditions can be assessed by a mean value and a variance. The relationship between the mean values of the cross section related maximum crushing forces FAmax and the corresponding sizes d of the specimens can then be described by mathematical functions. They are derived from different approaches (phenomenological, statistical and statistical-physical methods). The phenomenological methods are subjective and yield functions depending on the assumptions of a person, whereas the statistical and statistical-physical methods are based on an evaluated function and the optimization of the parameters.

Jan 1, 2014

By Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Istanbul Technical University, Mustafa Tarkan

"Zeolites are naturally occurring as hydrated aluminosilicate minerals. They belong to the class of minerals known as “tectosilicates” and are related to the common minerals feldspar and quartz. Seven natural zeolites that occur in large, commercially exploitable deposits, are: clinoptilolite, chabazite, mordenite, phillipsite, erionite, analcite, and ferrierite. Among them, clinoptilolite is the most abundant one and is not the best known, but is one of the more useful natural zeolite. Clinoptilolite [(Na3K3) (Al6Si30O72) 24 H2O] is very closely related to heulandite and is currently being considered for disuse it self as it may just be a variety of heulandite. It differs from heulandite significantly only in its enrichment in potassium and slightly more silica and it is argued that a separate mineral is not needed.There are large zeolite deposits in western part of Turkey. The sample used in this study was taken from the Gördes region of these deposits. Screen, chemical, XRD and mineralogical analyses were used to determine properties of the natural zeolite sample used in this work.According to the size distribution of the sample, it is found that the zeolite sample used in this study is below 1 mm in size and almost 80% of it is below 0.5 mm. X-Ray Diffraction (XRD) and mineralogical analyses show that the natural zeolite is found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. XRD analysis also shows that the sample contains approximately 58-60% clinoptilolite, 5% quartz, 5% feldspar, 10% smectite, 5- 10% illite and mica and remaining volcanic tuffs. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals."

Jan 1, 2003

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition.The article is devoted to the promotion of the concept of mineral processing in modern realitiesof the deficit of high-quality ores and increase their demand.Normative and methodical documentationsfor specific types of analysis with the definition of the field of application are shown. For example,the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore fieldare tested. The development of mineralogical methods, and testing of specific raw materials are shown.The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field. KEYWORDS Technological mineralogy, rebellious ores, ore quality assessment, ?mineralogical-analytical methods INTRODUCTION A highly intense production of many types of mineral raw results in gradual depletion and deterioration of mining-geological and mining-technical conditions of development. Relatively easily accessible and rich deposits are getting exhausted in the first place, and it is necessary to involve poor and rebellious ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral raw, creation of scientific and methodological prerequisites for solving the problem of rational development of mineral raw, maximal extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and raw base. The article is aimed at updating tasks that should be addressed within the applied mineralogical researches: – the forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of raw, – interactive monitoring of these indicators by mineralogical and analytical methods; – assessment of environmental consequences of mining and processing of minerals and measures that eliminate these consequences."

Jan 1, 2018

By K. C. Corin

It is well known that the grinding circuit plays a crucial role in flotation. The effect of pulp chemistry during grinding is often overlooked. It is believed that the surface properties of the minerals can be adjusted during flotation rather than during grinding. However, recent development in surface analysis techniques (TOF-SIMS, XPS, and AES etc.) have proven that the hydrophilic iron hydroxides formed at the mineral surface during grinding make it difficult for collector adsorption, which may result in poor grades and recoveries of the valuable minerals. This study investigated the effect of the pulp chemistry conditions during milling and the subsequent effects on flotation performance of an Nkomati ore. The results have shown that there was approximately 10 % increase in Ni recovery, when the ore was ground at a dissolved oxygen (DO) concentration of 0 ppm (DO-0) in comparison to no gas control during the grinding stage. However, when the pH was changed from 9 to 11, no gas control resulted in a 20 % decrease in the Ni recovery compared to only 5 % decrease in the Ni recovery at DO-0. A noteworthy observation is that controlling a combination of DO and pH during grinding is of critical importance for better floatability and selectivity for such a system. It also became clear from this study that the presence of oxygen is critical to the consumption of xanthate, which is consistent with the general literature. It has been established that grinding at lower DO levels/redox potentials (Eh) in the presence of xanthate significantly improves the flotation performance of the valuable minerals.

Sep 1, 2012

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By Subrata Roy

The slag produced in metallurgical smelting processes contains considerable amount of valuable metals. The present work focuses on recovery of copper value by froth flotation from the copper smelter slag. The slag samples are subjected to detailed characterization including automated quantitative mineralogy using Mineral Liberation Analyzer (MLA). The MLA results indicate that a part of copper is present in sulphide form in fayalite (iron-silicate) matrix and very poorly liberated. SEM-EDX analyses also reveal that a certain part of the copper is present within the fayalite (Fe-Ca-Si) matrix, perhaps either as lattice impurity or very fine grain. The copper smelter slag is ground in wet mode in a ball mill, to particle size distribution suitable for flotation. Subsequently, the slurry undergoes froth-flotation in lab-scale Denver-type flotation cell. Various combinations of sodium iso-propyl xanthate (SIPX) and alkyl hydroxamate collectors are used along with pine oil as frother. A multiple collector dosage is required for effective flotation of non-sulphide copper phases associated fayalite and alkyl hydroxamate is identified as one of the effective collector for non-sulphide minerals. The copper recovery can be enhanced by 7-10% with a combination of collectors as compared to conventional sulphide flotation using only xanthate type collectors. However, the grade decreases to some extent. Keywords: flotation, copper slag, hydroxamate collector

Sep 1, 2012

The flotation efficiency of magnetic concentrate of the Anhui hematite ore, which includes a great quantity of iron-bearing silicates, has been studied through reverse flotation test with a new type of collector Fly-102. The results indicate that collector Fly-102 has a strong adaptability to the variation of temperature, when the flotation temperature is in the range of 10? to 35?, using collector Fly-102 can obtain good flotation indexes. Collector Fly-102 has a strong adaptability to the variation of the slime contents and grades of the flotation samples. When the content of slime and the grade of the flotation feeds are 30% and 55.63% respectively, under the condition that the temperature is 15?, the open circuit flotation test was carried out with collector Fly-102. After one-stage roughing, one-stage cleaning and two-stage scavenging, a better result is got, the grade of iron concentrate reaches 67.12%, and the recovery of iron concentrate comes up to 84.15%.

Sep 1, 2012

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition. This article is devoted to the promotion of the concept of mineral processing in modern realities of the deficit of high–grade ores and increase in their demand. Normative and methodical documentation for specific types analysis with the definition of the field of application are presented in this paper. . For example, the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore field were tested. The development of mineralogical methods and testing of specific raw materials are shown. The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field.INTRODUCTION A highly intense production of many types of mineral deposits results in gradual depletion and of mining-geological and mining-technical conditions of various ore reserves ?. Relatively easily accessible and rich deposits are getting depleted in the first place, and it is necessary to involve low grade and refractory ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral deposits, creation of scientific and methodological pre-requisites for solving the problem of rational development of mineral deposits, maximum extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and ores.The article is aimed at updating tasks that should be addressed within the applied mineralogical research: – forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of properties ore, – interactive monitoring of these indicators by mineralogical and analytical methods;"

Jan 1, 2018

By G. Y. Zhou

During Zijinshan copper heap bioleaching, pyrite was leached in plenty resulting in high ferric concentration in solution. It has affected bioleaching and extraction processing greatly. It results much acid and iron in solution and bad effect to extraction processing. The paper studied the influence factors in the course of pyrite leaching and ferric ion chemical oxidation, especially studied the redox potential for copper bioleaching so as to find key factors affecting the dissolution difference between chalcocite and pyrite. The results show that the redox potential is important factor. Copper and pyrite leaching rates are 95% and 11% respectively and there is great dissolution difference between them at redox potential 700 mV (SHE). During pyrite bioleaching, the indirect action of bacteria gives priority to bioleaching cooperating with the direct attack of microbial cells attached to the mineral surface. Redox potential is determined by ratio of ferric and ferrous, ferric in solution was supplied by the way of oxidation of T. f bacteria, sufficient bacteria concentration and active character were two vial factors of controlling redox potential. It is indicated that copper can be selectively bioleached during copper bioleaching by controlling redox potential of bioleaching. The conclusion will provide theoretic foundation on balance of acid and iron during bioleaching for copper of higher S/Cu ratio. The experinment proved that bacteria activation was decreased on condition of both low pH value and intermittent aeratation during bioleaching. It resulted that the oxidation velocity of ferrous ion was decreased and redox potential was controlled. The dissolution of pyrite was depressed. It would be possible to actualize selective leaching of secondary sulfide copper ore during bioleaching process.

Jan 1, 2014

By Lawrence Bbosa, Aubrey Mainza, Indresan Govender

"Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to develop a probability based model for the power draw of a tumbling mill. Experiments are conducted using dry spherical glass bead charge in a laboratory scale tumbling mill, which is mounted with a torque transducer and tachometer to measure mill power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For both sets of data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. The information from both techniques is then used to develop a model for the power draw as a function of particle size, mill speed and volumetric filling. Predictions of the model match well with measured and calculated values. The model is found to predict mill power within close agreement with measurement and follows trends consistent with existing work on tumbling mill modelling."

Jan 1, 2014

By Garren Edwards, van der Westhuizen. Andre

"Due to the depletion of easily treated coarser ores, more mineralogically complex ores with smaller valuable mineral grain sizes are treated, the means to liberate these minerals lies in grinding finer (Partyka & Yan, 2007). Grinding to these fine sizes is energy intensive, and using standard ball mills are energy inefficient at these sizes (P80 < 75µm). Therefore, stirred mills are becoming increasingly prevalent in the mineral processing industry. In order to optimize these mills, the effects and mechanisms of the significant variables need to be understood. This paper investigates a laboratory scale vertical stirred mill (Deswik mill) in an ultra fine grinding application of a South African platinum ore. The operating variables that are considered are stirrer speed, media size, media filling, and slurry density. The resulting grinding efficiencies are considered in two ways. Firstly, a statistical model is fitted to identify the effect of the significant variables on grinding efficiency, and secondly, the grinding efficiencies are also considered in terms of a stress energy model to determine whether this can partly explain the grinding mechanism in this mill. A factorial design of experiments was used on three levels for each variable, such that only linear interactions, second order interactions and two variable interactions are included in the statistical model. The results show that tip speed, media size, percent solids and mill filling are all significant to the grind, at differing energy inputs in the grinding process. The interaction effects of these variables are also dependent on the energy inputs. The results also found that the Kwade stress energy model is applicable to this mill and can be very useful to find the most efficient operating conditions for this system. The most energy efficient operating conditions in terms of mill speed and media size were typically somewhat below the standard operating conditions and it is expected that this is most probably done in order to increase the grinding rate, but at the expense of sacrificing some grinding efficiency."

Jan 1, 2014

By Tohru Kamo, Shigeyuki Katano, Hideki Nakagome, Maiko Adachi, Shingo Nakamura, Kaneshi Taniguchi, Zar Zar Hlaing, Takaaki Wajima

Tantalum capacitor is a small-sized and has large capacity, and is indispensable for electric equipment. The demand increases year by year, and a quite large number of used tantalum capacitors is generated. Recovery of tantalum from tantalum condenser is recently important since production of tantalum have not been stable for the price and the quality. However, recovery of tantalum from tantalum-condenser is difficult since tantalum parts strongly cover with the flame retardant resin made of halogenated compound (mold resin). This research investigated recovery of tantalum parts from tantalum condenser using steam gasification with mixed molten carbonate. Mixed molten carbonate (Na2CO3:K2CO3:Li2CO3 = 1:1:1) (3 g) put into the reactor, and heated with electric furnace while flowing nitrogen (160 mL/min) and steam (1 mL/min) warmed by heater. After heating to setting temperature (450 - 650 oC), tantalum condenser (3 g) was put into the reactor, heated for 5-10 min, and then cooled to room temperature to recover the reacted capacitor by filtration after treating with distilled water. At relatively low temperature (550 oC) heating for 10 min, mold resin can be decomposed by using steam gasification with mixed molten carbonate, in comparison with using pyrolysis and steam gasification without carbonate, and decomposition reaction occurred over 500 oC by using steam gasification with mixed carbonate. Recovery of tantalum parts from capacitor is successful using steam gasification with mixed molten carbonate at 530 oC for 5 min, due to the effective decomposition and removal of mold resin from capacitor. Furthermore, most halogen gas generated from decomposition of mold resin can be trapped in molten carbonate not to exhaust halogen gas. These results suggested that recovery process of tantalum parts from used condenser using steam gasification with mixed molten carbonate is expected as a feasible way to recycle the rare metal in electric equipment.

Jan 1, 2014

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012