Search Documents

By M. L. Torem, R. H. Rojas, A. G. Merma

"Fine particle recovery by conventional flotation processes is very low mainly due to the low probability of bubble/particle collision and adhesion. In order to solve the problem of low particle recovery, several flotation technologies have been developed to increase bubble/particle collision efficiency. Among these technologies, the electroflotation process stands out. This process has advantages in the generation of microbubbles (<100 µm) and in the production of different amounts of hydrogen and oxygen microbubbles. These advantages favorably influence the fine particle floatability, due to the greater probability of particle/bubble collision and adhesion. The electroflotation tests were conducted for a hematite/sodium oleate system in a Partridge-Smith modified electroflotation binary cell of 0.38 L usable volume. The sodium oleate concentration, particle size, pH and current density were evaluated. Satisfactory results in the recovery of hematite were found at pH values of 7, reaching hematite floatability of 99% and 90% with hydrogen and oxygen bubbles, respectively.INTRODUCTIONThe flotation recovery of fine and ultrafine particles is normally very low and is caused by several factors, among them, the low probability of collision and adhesion bubble-particle, the difficulty to overcome the energy barrier (entrainment and entrapment), low selectivity, surface oxidation and mineralogical changes (Schulze et al., 1989; Waters et al., 2008; Shahbazi et al., 2010). This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However, it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. Electroflotation is one of the variants of the flotation process, where the gaseous phase is produced by electrolysis of an aqueous solution, generating oxygen and hydrogen bubbles (Sarkar, 2010; Gupta and Ali, 2012). These smaller size bubbles allow the recovery of fine particles by increasing the collision efficiency. This process is versatile and competitive in relation to other techniques such as dissolved air flotation and dispersed air flotation because the electroflotation units are smaller, more compact and require less maintenance and less operating cost than other flotation units (Zouboulis and Matis, 1995,). In addition, the electroflotation process is a clean technique and provides results in a short time, requiring only the investment in the electroflotation cell construction stage and the choice of the electrodes (Ketkar et al., 1991; Sarkar et al., 2010; Sun et al., 2011). In this sense, this study assesses the effect of pH, particle size and sodium oleate concentration on electroflotation of hematite fines."

Jan 1, 2018

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By G. V. Sedelnikova

Biohydrometallurgical studies were performed on the sulfide gold-arsenic concentrate obtained in treatment of refractory ore from a deposit located in northern Russia. Gold is disseminated in sulfides-arsenopyrite, pyrite and antimonite (their content is 10.0%, 30.4% and 0.7%, respectively). Gold extraction is only 11.8% by cyanidation. Results are given for test bacterial oxidation of the concentrate in continuous mode at temp. = 28~32°C using mesophilic bacteria and at temp. = 32~38°C using the association including moderate thermophilic bacteria. The paper shows that the use of moderate thermophilic bacteria allows to speed up sulfide biooxidation and reduce its time to 96 hours compared to leaching at temp. = 28~32°C for 110~120 hours. The optimal range of pH = 1.5~2.0 of biooxidation process was determined where bacterial solutions are produced with the molar ratio Fe:As > 3 necessary for precipitation of hard-to-solve, environmentally safe arsenical precipitates. Electron microscopy showed that sulfide biooxidation results in liberation of disseminated gold with nanoparticle-level sizes. High sorptive activity of carbonaceous matter and other compounds of bacterial residues cause low gold extraction into cyanide solution ? 28.7%. 10% resin load makes it possible to extract 88.1% Au. Aeration of pulp in calcareous medium enhances extraction to 95.7% and decreases cyanide consumption from 17kg/t to 8 kg/t.

Jan 1, 2014

By Peter Ay, Florian Logsch, Satyanarayana Narra

"The traditional lignin separation process from the precipitated suspension creates severe filtration problems by plugging of the filter medium due to the small particle size (20 to 60 µm) of the suspended lignins. The plugging causes further problems in the successive processing of the filter cake. A new lignin separation process has been developed at the Brandenburg University of Technology (BTU) Cottbus as a part of the Research and Development and Demonstration (R & D & D) project "LignoBioFuel". The new developed process separates lignin in the form of granules with diameters ranging from 100 µm to 300 µm. The restrainment of the granule’s size in their successive treatments is expected to result in higher filtration efficiencies and reduction in plugging of filter mediums. To evaluate the filtration efficiency, the filtration resistance of the produced granules as well as the conventional suspensions has been investigated. The results show that there is a 60 to 80 % filtration efficiency increase and around 60 % reduction in plugging of filter mediums with the lignin granules in comparison to the conventional suspensions. Furthermore the successive processing of lignin granules was easier due to their porous structures removing the impurities such as adherent acids and salts. The purity of the separated lignin was measured with their sulphur (reduced from 7 % to 2.7 %) and ash (reduced from 46 % to 0.5 %) contents. The newly developed process has displayed better results in comparison to that of the conventional process. The new process displays high potentials in optimizing and improving the present state of the art treatments and is promising several ecological, economical and environmental improvements."

Jan 1, 2014

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By Chuanyao Sun, Longli Liu, Fayu He, Guiye Wu

Utilizing thioglycolic acid (TGA) as a template and using structure-guided design, a molecular modelling approach has been used to design and screen appropriate dispersant for chalcopyrite. A series of organic dispersants based on a TGA substitution with hydroxyl and amino and sulfonic functional groups have been examined on chalcopyrite surface. 20 organic depressors of chalcopyrite have been investigated to study the quantitative structure-activity relationship (QSAR) of chalcopyrite depressors. For the chalcopyrite surface, depressor containing carboxyl and sulfonic group is generally stronger than the depressor containing hydroxyl group. Increasing the number of hydrophilic group can effectively enhance the inhibition. Increasing the number of Solidophilic group does not necessarily lead to enhanced inhibition ability; steric factor is one of the important factors to affect the interaction. Extension alkyl carbon chain length cannot enhance the interaction of depressors. Isomers principle as well as applies to the chalcopyrite depressor molecular design. Flotation verification tests further confirmes the accuracy of the molecular simulation. Through the Computer Aided Molecular Design (CAMD) technology, we can save enormous time and resources to design novel surfactants. This research and application will play a great significance role in sulfide flotation.

Jan 1, 2014

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By Johannes Käppeler, Alexander Weh, Harald Giese, Klaas van der Wielen

"High voltage breakage is a novel comminution technology that shows considerable potential for various applications in mineral processing and recycling. It relies on highly energetic electrical pulses to induce electrical explosions in rocks, causing the formation of plasma channels and powerful shockwaves that result in fracturing and fragmentation of particles. There has been considerable interest in this technology for its ability to weaken rocks and preferentially liberate target minerals, as previously demonstrated by other authors. Weakening has the potential to significantly reduce energy consumption during comminution, or alternatively, increase throughput of a circuit. Better liberation may yield an improved concentrate grade and/or recovery, reduce fines losses to tailings or increase the grind size required for liberation, thereby also reducing energy requirements. This review aims to increase general awareness of this technology, and promote further research into it by providing a general summary of the theory underlying high voltage breakage, as well as the envisaged applications of this novel technology. A brief history of the technology is presented before progressing onto the physics underlying the electrical and geomechanical aspects of high voltage breakage. Key results regarding weakening and liberation are discussed, and some mention is made of current challenges and planned developments to increase the throughput of high voltage breakage units to the level where it can be integrated into new and existing processing circuits."

Jan 1, 2014

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By J. X. Zhang, F. S. Niu

"In order to accurately detect whether the collision occurs between particle and bubble in flotation process, a collision detection method of particle and bubble, which based on morphological image processing and Otsu method, is presented. First of all, it utilizes image pre-processing to optimize images, the target area and the background area are segmented by Otsu method. Then, particle and bubble are fitted to a circle combined with the least-square method. It’s convenient to obtain the coordinate information and radius. Finally, the position of all particles is extracted to an image, which achieves the particle tracking and avoids the complexity of the continuous frame image tracking.Experimental analysis shows that the relationship between the two ordinate difference d and the bubble radius r has a certain influence on the collision detection when the dripping particles are close to the bubble, when d>r, the detection accuracy is 92%;When d=1/2r, the detection accuracy is 97%;When d=0, the detection accuracy is 100%. The result indicates that this algorithm can detect the collision between particle and bubble quickly, and the working hours of manual test are saved effectively ,the best position of dripping particles close to the bubble which is taken with a CCD camera should be in the range of the particle and bubble’s ordinate difference less than half of the bubble radius.INTRODUCTIONFlotation is an important technical means to separate useful minerals from ores. The flotation process of ores and materials in the world is treated by flotation technology up to billions of tons every year, so the study of flotation process is particularly important. Raising the collision probability between mineral particles and bubbles in flotation process is one of the key factors to improve flotation separation efficiency[1]. The study indicates that[2-4] the collision probability between particles and bubbles is influenced by many factors, such as particle density, particle size bubble size, etc. The analysis of these influential factors requires a lot of experiments. Therefore, it is of great significance to design an accurate collision detection method for the research of this field."

Jan 1, 2018

Flinders Power, formerly NRG Flinders, is considering the possible use of low rank coal from Lake Phillipson, South Australia (SA) in its power stations at Port Augusta, SA. Typically, this coal contains about 35% moisture and 10% ash. Unfortunately, it also contains high levels of sodium (1% Na) and chloride (0.95% Cl) with a Na2O level in ash of 18.9%. Such levels cause serious problems during coal combustion, making the use of as-mined coal impractical for power generation. This paper describes the development of an aqueous leaching technique to remove 90% of the sodium and chloride and to yield a product with a Na2 O level in ash of less than 3%. Small-scale agitation leaching tests with good quality tap water at ambient temperatures showed that the coal needed to be crushed to minus 5.6 mm to obtain maximum removal of water-soluble sodium and chloride in 30 min. Leaching kinetics, but not the ultimate removal of salt, were enhanced by the use of higher temperatures (up to 150°C), but this was deemed uneconomic. Varying the pulp density between 20% and 50% had little effect on extractions and there was no benefit in multiple stage water washing. The best results by water leaching were 69%~74% extraction for sodium and 95%~97% for chloride, meaning that the sodium removal was well below the target level. From SEM examinations of the leached product it was concluded that the remaining sodium was organically bound to the carbon atoms in the coal. Further tests using aqueous solutions containing cation exchange additives such as calcium chloride (CaCl2) or ammonium chloride (NH4Cl) or sulphuric acid (H2SO4) showed that significantly enhanced sodium extractions were possible and target specifications were met. Two options, namely a single-stage and a two-stage leach, were then investigated. In a single-stage leach with additive, minus 5.6 mm coal was leached at 33%~50% solids for 30 min at ambient temperature and then filtered and washed with fresh water. This gave a sodium removal level of about 81% and a Na2O level in ash of about 5%. These levels do not quite meet tar-get specifications. In a two-stage leach, the coal was first leached with water alone without an additive as in the single stage leach, and the washed residue re-leached under similar conditions for about 5 min with an additive (CaCl2), and then filtered and washed. This gave a cumulative sodium removal of 96% and a Na2O level in ash of 1.4%~2.4%. These levels are well within target specifications.

Jan 1, 2014

By Vladimir E. Vigdergauz

"Bubble-mineral complexes could be formatted by an attaching of hydrophobic particles to the surface of air bubbles or by an evolution of bubbles from solution onto hydrophobic surfaces. Measurements of contact angles, detachment forces (DF), induction times (IT), evolution pressures (EP) and flotation recoveries (FR) for the studying of minerals wettability at various pH and electrochemical potentials were used. An analysis of the obtained IT results show that a process of bubble attachment to a mineral surface is a rather slow one and it will scarcely be enough for bubble-mineral complex formation under the conditions of real flotation.The ranges of adhesion potentials obtained by DF measurements, Figure 1, correlate with the data of floatability-potential for pyrite. The ranges of adhesion potentials obtained by DF measurements for galena (-1 ÷0.2V) and chalcocite (-0.5÷1.2V) correlate with the potential ranges of floatability for galena (<0.2V) and chalcocite (>-0.4V). An increase of the DF and the cathodic limit of the adhesion potential with increasing length of the hydrocarbon chain were observed. EP-pH curves for sulfides are a mirror-like to the DF-pH curves, Figure 2. Structure of solid-liquid and liquid-gas borders has a determinative importance for formation of bubble-mineral complexes and subsequently flotation results. Under vacuum on the mineral surface there are produced micro bubbles and preferably they will be appeared on the hydrophobic sites. Water structure breaks near a hydrophobic surface facilitate water mass destruction and formation of gaseous phase embryos under decompression in the impeller zone. It simultaneously reduces a probability of produced micro bubbles dissolution as a result of pressure increasing owing to constant fluctuation of liquid densities into impeller zone. Comparison of Taggart’s evaluation of the suction behind blades of the impeller of an agitation-froth machine and ABEP data on galena, Figure, shows that gas evolution will be observed in the range of 1300-2700 revolutions of impeller per minute for hydrophobic and hydrophilic surfaces successively."

Jan 1, 2003

By O. D. Khmelnitskaya

The research on selecting of an efficient technology of pyrite cinders complex treatment, sulfuric acid production wastes, have been made. The grades in the initial product were 2.04 g Au/t, 35.0 g Ag /t, 0.38%Cu, 1.1% Zn. Laboratory tests on cyanide technology, thiourea and sulphite leaching were carried out. Magnetic and flotation beneficiation and biohydrometallurgical technology were tested. After considering the results of the tests, the most economically efficient technology of pyrite cinders complex treatment with cyanide leaching of precious metals was determined. The technology involves water washing of soluble copper and zinc compounds, lime treatment and cyanide leaching of gold and silver, detoxification and utilization of mineral wastes. The precious metals are recovered from solutions by cementation onto zinc. Copper is recovered from rinse waters by SW/EW and then zinc is precipitated as hydroxide. All the solutions and organic agent are used in recirculation and therefore the technology is practically waste-free. Mineral wastes can be used as iron-containing materials for cement industry. The technology has been tested in pilot-plant scale under continuous operation with complete re-circulation of cyanide solutions. In this process recovery of 54% Au, 45% Ag, 30% Cu and 50% Zn has been achieved.

Jan 1, 2014

By R. P. Bhagat

The paper reports results on sinterability of iron ores from the mines of Tata Steel Limited. The objective was to improve tumbler index (TI) of sinter and its reduction parameters, reduction degradation index (RDI) and reducibility (RI) while maintaining strand productivity same or to improve. Pot sintering experiments were carried out with Joda and Noamundi mines having LOI 3.8% and 2.9% respectively. Sinter basicity (CaO/SiO2) was varied in the 2.1 to 2.5 range and its MgO content was kept in the 1.4% to 1.8% range according to the blast furnace requirement. The ignition condition and vacuum was maintained according to the plant practice. The effect of variables namely, granulometric composition of ores vis-à-vis that of sinter mix, bed height, solid fuel, moisture content of green mix on the sintering indices was studied. The productivity with Noamundi ore (26 %+6.3 mm) was lower than that with Joda ore (45% +6.3 mm) at 4% coke in the mix and sinter basicity (CaO/SiO2) 2.1. However, with 4% coke (ash 22%) the RDI value was significantly high in case of Noamundi Ore, which decreased significantly to 29% with 5% coke. The size parameter of ore fines and its LOI content do influence the sintering speed and the sinter properties significantly. At 2.1 basicity ratio, the sinter with the Joda ore having coarsergranulometry had highest TI (=70.2%). The RDI (27%) in this case was inferior to that (23.2%) when Joda ores with finer size was sintered. Better RDI with finer sized ore could be attributed to better assimilation of CaO/ MgO with more balanced and uniformly distributed hematite minerals. The size parameter has been inter-influenced by the coke requirement. With the lower mean sized Joda ore the sinter RDI decreased significantly to 23% and the productivity improved to 42.9 T/(sq m*d) when the coke in the mix increased from 4% to 5%. An attempt to reduce the coke in the mix from 5% to 4% with respect to both the ores was not successful as it resulted higher RDI and lower strand productivity. The present study has revealed that sinter RDI improves (decreases) with decrease in the sintering time, while such correlation was absent between TI of sinter and speed of sintering. Corollary to this observation, one can take advantage of other stronger parameters to increase the sintering speed (and hence sinter productivity) without affecting the sinter strength. In the present study higher FeO sinters has displayed excellent RDI, however cold strength of sinter was not correlated with its FeO content. The TI and RI parameters of sinter improves marginally with increase in its MgO content while RDI got worsened. Keywords: LOI content, iron ore, reduction properties, sinter, noamundi, joda

Sep 1, 2012

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

By S. K. Pan

The process flow-sheet adopted in treating hematite iron ore in India through wet circuit generates not only 15-25% slime of Run-of-Mine (ROM), but also results in loss of very high quality fine iron ore particles along with it. As the reserves of hematite iron ore is depleting, it is necessary to explore the possibility of upgrading other types of low grade iron ore and slime for recovery of iron minerals; extensive research in this field is being carried out. While beneficiation of low grade ore is yet to be established, slime beneficiation has been quite successful and many installations of slime treatment plant are underway. In SAIL mines, the slime is mainly the discarded particles from Classifiers, which are less than 0.2 mm sizes. R& D initiative has been focussed on the beneficiation of the slimes (49-60% Fe, 3-10% Al2O3 & 4-10% SiO2) of Dalli mines to generate concentrates assaying 62-64% Fe, 2-3% Al2O3, 3-4% SiO2 and a few innovative facilities for the same has been introduced at this mines of Bhilai Steel Plant (BSP). At Dalli mines, the slime is of very poor quality. A typical slime analysis assays 48.54% Fe, 15.1% SiO2, 8.5% Al2O3 and consists nearly 60% (by wt.) particles less than 38 micron. Slime analysis revealed substantial quantity of very high density mineral particles, those causes jamming of Thickener due to faster settling. A novel technique has been implemented to classify the concentrate ore particles from the gangue mineral particles by processing through Fluidized Bed Classifier (FBC) system, which is a gravity concentrator, to treat 50% of the slime generated and the rest is treated through de-sliming hydro-cyclone followed by Medium Intensity Magnetic Separator (MIMS). A special self-vibrating launder has been designed and introduced into the system to recover tiny iron ore particles, which could not get captured by the permanent Neodymium rare earth magnet in MIMS. The classified iron mineral particles from FBC are further treated in a battery of hydro-cyclones followed by modified Slow Speed Spiral Classifier (SSSC) unit. Multiple feed entry system to the SSSC unit is unique and use of particular feed entry point depends on the desired quality of the product and thus converted to a beneficiation equipment rather than mere de-watering unit. By processing slime in FBC system, the valuable iron ore particles with 62.5% Fe, 5.2% SiO2, 2.23% Al2O3 has been recovered from the slime at a material yield of 30%. And very high valued concentrate particles with more than 65% Fe has been sorted out through the magnetic separation route. The overall extra production of beneficiated slime concentrate is 40-45 tph with 63-64% Fe from a slime feed of 120-130 tph solid. This paper outlines few new approaches in iron ore slime beneficiation at Dalli mines for maximum recovery of valuable minerals. Keywords: fluidized bed classifier (fbc), iron ore slime of dalli mines, medium intensity magnetic separator, slow speed spiral classifier (sssc)

Sep 1, 2012

"Wet low intensity magnetic separation has been used for the recovery of magnetite for decades. As high-grade reserves continue to decline, low grade magnetite ores are being targeted for iron production. Low grade magnetite mineralisation is typically fine grained and requires fine to ultrafine grinding (P80 40 - 30 µm) to liberate it from, predominantly, silica/silicate gangue matrices. Grinding to such particle sizes requires high power consumption and produces excessive fines which impact negatively on wet magnetic separation and tailings dewatering. In addition, the dearth of fresh water for mineral processing in arid areas impacts negatively on the economic viability of low grade magnetite projects. These challenges have motivated innovation in dry magnetic separation technologies for the beneficiation of magnetite that can be economically applied on a large-scale. Such technology has been developed in the Cyclomag Planar magnetic separator (PMS) invented by South Australia-based Christopher Kelsey of IMPTEC P/L. The significant gangue mineralisation associated with magnetite ores in South Australia is quartz. In this study, the performance of the Cyclomag PMS on the recovery of magnetite mineral from magnetite-quartz blends was investigated. Magnetite-quartz blend were subjected to the PMS at varying control parameters - magnet discs rotation speed, inlet airflow and feeder speed. The study showed a successful dry separation of magnetic mineral from non-magnetics using the Cyclomag PMS. The PMS has potential to effectively recover magnetite mineral."

Jan 1, 2018

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014