Search Documents

By Reinol Compañero, Ivy Gonzales, Herman Mendoza, Brian Buenaventura

"The extraction of gold in the Philippines has been a significant challenge for the past decades. Around 70-75% of gold mined in the country can be accounted from the small-scale mining industry which primarily use the traditional cyanidation and amalgamation; processes which have been advocated due to its adverse affects to health and environment. To address this challenge, an alternative clean and sustainable technology was developed for the small-scale miners to recover gold and other metal/mineral values efficiently from Philippine ores. An initial survey was conducted and followed through with extensive mineralogical investigations ascertain the best method applicable. It was determined that Philippine gold occur in ore as (1) very fine particles in the microns range, (2) free-milling, which is in abundance, and (3) locked particles with sulfides --- it was concluded that enhanced gravity concentration and flotation are viable alternatives. A comprehensive test regime was followed to check the response of the ores obtained from different small-scale mining districts across the country. It was shown conclusively that the gold ores respond positively, with recoveries using gravity concentration and flotation of at least 95% and 88%, respectively; exceeding the nominal recoveries using cyanidation or amalgamation. A specific process flow was designed for each type of ore with customized parameters. It was determined that while capital expenditure of implementing these alternative processes is higher than what is currently being used, the operational aspects show that it is much more economical to apply enhanced gravity and flotation. It should be noted that the process developed addresses the critical issue of environmental costs which should be more than enough to justify the shift from the current to the novel and sustainable technologies."

Jan 1, 2014

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By T. Tsurata

The accumulation of thorium and/or uranium by various microorganisms from a solution containing thorium and/or uranium at pH 3.5 was examined. Among the species tested, a high accumulation ability for thorium was exhibited by strains of gram-positive bacteria, such as Bacillus megaterium, B. subtilis, Micrococcus luteus, Rhodococcus erythropolis, and actinomycetes, such as Streptomyces levoris. On the other hand, though uranium was accumulated in small amounts from the solution containing both elements by all these microorganisms, actinomycetes, such as S. flavoviridis and S. levoris had relatively high uranium accumulation abilities. In these high performance thorium- and uranium- accumulating microorganisms, S.levoris, which accumulated the largest amount of uranium from the solution containing only uranium at pH 3.5, could accumulate about 300 µmol thorium and 133 µmol uranium per gram dry wt. of microbial cells from a solution containing both thorium and uranium at pH 3.5. After this screening, uranium accumulation using microorganisms isolated from uranium mines, among which some strains of bacteria were found to possess an extremely high uranium accumulating ability. The microbial biomass may thus be considered for use as an accumulating agent for the removal and recovery of uranium that may be present in metallurgical effluents, mine tailings, seawater and other sources. Recently, hundreds of micro-organisms existing in uranium deposits located in North America, Australia, and Japan for their ability to accumulate large amounts of uranium, and found some new strains which accumulated large amounts of uranium, such as Lactobacillus and Bacillus sp. from Japanese and Arthrobacter and Bacillus sp. from the United States uranium deposits. These bacterial strains can accumulate about 2500 µmol uranium per gram dry wt. of microbial cells within one hour. These microbial cells can remove uranium from the uranium refining wastewater with a high efficiency. The accumulation of uranium from a solution (pH 5.8) by microorganisms contained Arthrobacter nicotianee, which is a similar strain mentioned above Arthrobacter sp., was examined. Among the 76 strains of 69 species tested (23 bacteria, 20 actinomycetes, 18 fungi, and 15 yeasts), high uranium accumulation ability was exhibited by strains of the bacteria, A. nicotianae, B. subtilis, and M. luteus. A. nicotianae cells, which showed the best performance, could accumulate about 698 mg uranium (2.58 mmol) per gram dry wt. of microbial cells.

Jan 1, 2014

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:- flotation tailings of crystalline graphite minerals- outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers.The most important variables affecting the leaching process, such as grain size, mineralogical species, reagent consumption, and so on, were previously studied. (Weiss, L.1985)On the basis of the present study results, the possible definition of an economically viable mineralization will be analyzed to define an auriferous district."

Jan 1, 2003

By M. L. Cao

In this study, a montmorillonite organo-intercalation compound (MOIC) was synthesized by using a Na-modified bentonite (NaB) as a matrix and hexadecyltrimethylammonium (HDTMA) bromide as an intercalating reagent under microwave irradiation. The synthesized products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), organic carbon content measurement, and adsorption density determination. The results show that, at 10% suspension concentration and 10 minutes irradiation in a 130-W microwave oven, the basal spacing d(001) of the synthesized MOIC increases to 2.209 nm from the original 1.218 nm of NaB. The MOIC has much higher adsorptive densities to nitrobenzene and aniline from aqueous solution than the NaB. The adsorption isotherm of nitrobenzene on the MOIC is linear, and the adsorption is mainly the result of nitrobenzene?s preferred partition in MOIC over aqueous solution due to MOIC?s hydrophobicity. The adsorption isotherm of aniline on MOIC follows the Freundlich equation and the increased adsorption is not only the result of aniline?s preferred partition in MOIC over aqueous solution but also that of the MOIC?s surface adsorptions.

Jan 1, 2014

By Bharat Garg

The coking coal or clean coal from raw material division, Tata Steel Ltd. is a prime source of energy for inhouse steel making. Coal reserves of semi soft coking coal at West Bokaro is beneficiated by dense media cyclone and froth flotation processes to produce clean coal. In dense media cyclone process two byproducts-middling and rejects are also produced along with clean coal. With the growing demand for clean coal, it becomes imperative to maximize the recovery of clean coal in beneficiation processes. This will help, not only in reduction in cost of production, but also in raw resource conservation, and proper utilization. In this context, a case study was conducted at West Bokaro to identify opportunities for clean coal recovery from by-products. This paper mainly discusses the process for recovery of clean coal from byproducts and study of further liberation of clean coal from byproducts for economic consideration.

Sep 1, 2012

The objective of the paper is to develop a material balance calculation procedure for a production unit involving two plants separated by a pipeline. The case study is taken from the oil sands industry. The raw sands are first mixed with water in a conditioning plant, then transported through a pipeline to an oil extraction plant. The combination of pipeline dimensions and nominal throughput creates a significant variable time lag between the two plants. As usual, mass balance calculations required for the evaluation of plant performance indicators, such as bitumen recovery, are inaccurate due to measurement errors. In addition, in the present case study, the time lag of the pipe creates an additional source of uncertainty, which may lead to misinterpretations and wrong decisions. Raw data are usually reconciled through steady-state mass balancing, to correct for measurement errors. However, because of the significant pipeline dynamic lag, standard steady-state daily mass balance may fail at giving an appropriate picture of the operations. The proposed solution to the data reconciliation problem includes the use of a pipeline plug-flow model in the mass balance calculation. To fulfil the industrial constraint that current data reconciliation must not modify past reconciled values, while still satisfying dynamic constraints, a daily one-step method, i.e. a unitary filter-ing horizon, is recommended. The method is illustrated with simulation data, and the results com-pared to those of standard data reconciliation methods.

Jan 1, 2014

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By X. Q. Cui

The surficial collapse pits of the mining areas are continuously spreading in Beiminghe iron mine of Hebei Province as a result of the exploitation, which has done a lot of damage to the circumjacent ecological environment of the mine. It is a new path to handle the mine tailings at the present time that the thickened tailings are used to backfill the collapse pits, in which way the problems of the surficial collapse and the nowhere discharge of the tailings are both solved, and the rational utilization of the mine tailings and the clean production of the mine enterprise are realized. The?200 mesh content of the tailings of Beiminghe iron mine is 76.87%, and?325 mesh content is 63.50%. Semi-industrial dehydration experiments to the tailings have been done using the hydro-cyclone classified thickening process. The results show that when FX125 hydrocyclone is adopted, the concentration of underflow can achieve 73.31%, and the yield ratio is 61.78%; when FX150 hydrocyclone is adopted, the concentration of underflow is 70.57%, and the yield ratio is 54.31%, which indicate that the minor diameter hydrocyclone is propitious to improve the yield ratio of the underflow. The semi-industrial dehydration system of hydrocyclone classified thickening process is com-posed of FX125 hydrocyclone, D3600 high-efficient thickener and D2000 thickening bucket. The capacity to tailings disposal can achieve 3.07t/h and the tailings can be thickened from 28.86% to 62.45%. Compared with the traditional thickening-filtrating process and the total tailings directly filtrating process, the hydrocyclone classified thickening process has the merits of simple flow and high thickening efficiency, so it is easy to be realized in the mine.

Jan 1, 2014

The simulation study on the process of iron ore beneficiation plant of Essar Steel, Kirandul was carried out. The iron ore fines and slimes generated nearby Bailadila mines of NMDC are used as raw materials for this beneficiation plant. The capacity of the plant is 1400 TPH operating in parallel in two streams. The capacity of the plant was utilized about 60% of throughput capacity. To improve the plant capacity as well as quality performance, the simulation study was conducted to detect the bottleneck of the process. The process samples were collected from input and output of each processing unit operation to generate the data base for simulation study at the feed rate of 400 and 500 TPH of iron ore fines in a single stream. The characteristics data i.e., breakage and selection functions were generated using MILLSOFT package for simulation of ball mills. Then MODSIM package was used to evaluate the performance of each unit operation to identify the bottleneck. It was established by a simulation study that the intermediate thickener draws high current when the feed rate is more than 400 TPH due to high torque drawn by rotating rake because of presence of coarse particles in the input stream to thickener. The problem was sorted out by classification of input stream of thickener to remove the coarse particles. Then the process was simulated at its rated capacity, and experimental validation studies at the plant were also conducted at the feed capacity of 600 and 700 TPH by modification of process flowsheet. The experimental data was almost matching with simulated data. Finally, the processing plant is running with full rated capacity without any bottleneck. Keywords: simulation of ball mill, breakage function, selection function, iron ore

Sep 1, 2012

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By Ashok Kumar, Subhadra Sen Dr. Rashmi Kumari, D. P. Chakraborty, Ajay kumar Gupta

The blast furnace coke quality depends on the characteristics of coal blend, pre-carbonization techniques adopted such as stamping, vibro-compaction etc., and coking conditions. Of the above, coal blend plays a significant role in the production of quality coke. Furthermore, the quality of the blend depends on the quality of individual coals and their interaction making up the blend. During transportation and stockpiling, coal is in contact with air for periods of time that sometimes may exceed several months. During this time, reaction with oxygen in the presence of water, sunlight and possibly elevated temperatures may take place. The resulting weathered coal suffers some alteration in its technological properties, which in turn affects coke quality for Blast Furnace operation adversely. In this work, two coals belong two prime hard coking and hard coking categories, namely Illawarra & Tahmoor, were selected and kept in a separate stock pile for a period of 120 days. These coals were characterized in terms of proximate, rheological & petrography properties at a regular frequency. This report summarizes the impact of weathering on the coking behaviour of these two coals in terms of properties as mentioned above. However, the rate of loss depends on coal rank and storage conditions. This has been seen through this study that the loss depends on coal rank and storage conditions. Deterioration of rheological and petrographic properties were seen higher for low-rank coals, like in this study Tahmoor, which is a low rank coal, compared to Illawarra showed higher degree of coking property degradation within the same time period under identical environmental conditions. Low-rank coal deteriorates at a faster rate because low-rank coal is dominated by free radicals that easily react with oxygen, resulting in the creation of various carbonyl groups and weathered vitrinite. Based on the results obtained in this study, size of stock piles for different qualities of coals to be maintained, at a specific time, can be determined and recommended, so that target coke quality is always achieved.

Jan 1, 2018

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By M. K. G. Vermaak

Kimberlite weathering has been a topic of ongoing research within De Beers for many years. Using kimberlite weathering as an alternative to crushing has many advantages e.g. power and reducing diamond breakage. Weathering could also possibly be used in conjunction with crushing just to weaken the material and reduce power consumption. These forces have driven current research to investigate whether kimberlite weathering could be utilised for these reasons. Weathering in this context does not refer to weathering over long period of time but rather to disintegration of the material in aqeous media in relative short time periods. Previous published work discussed that the presence of smectite renders kimberlite weatherable and that the amount of smectite determines the rate of weathering (Morkel and Vermaak, 2006). The current work investigates whether cation ex-change or the adsorption of organic species in the smectite interlayer could influence the observed weathering behaviour. The results show that cation exchange does take place in the presence of cation species and that the weathering behaviour can be drastically improved with especially Cu2+ cations. Concentration and time effects of the weathering was also investigated. Weathering tests with organic species such as ethanol, methanol, edta, pentanol, butanol, acetic acid and oxalic acid was performed. The results show that organic species does improve weathering but under these testing conditions was not as effective as cations.

Jan 1, 2014

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

The ultimate goal of a mineral processing plant is to recover as much of the target mineral(s) as possible from the ore being treated to achieve the best economics. Selection of the mineral processing techniques is the most important step in achieving this goal. However, due to the complexity of the ore, the recoveries of valuable minerals may be not satisfactory even when the mineral processing technique(s) are well chosen. In other words, minerals of interest can be lost to the tailings for mineralogical reasons. For example, gold is mainly extracted from the ore by gravity, flotation, cyanidation, or a combination of these processes, and high recovery (>90%) can be achieved when gold occurs as coarse grains. However, when a refractory ore is being processed, gold extraction will be challenged by mineralogical factors, which often cause gold losses to various tailings. Mineralogical factors affecting gold recovery mainly include grain size, shape, surface coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of slow-dissolving gold minerals and the refractory nature of submicroscopic gold. Among these factors, locking in sulphide, silicate and other minerals as fine-grained gold inclusions and/or as invisible submicroscopic gold is by far the most common factor leading to poor gold recovery encountered in gold ore processing. Processing of PGE ores faces the same challenges as gold. Small grain size and locking of PGM in sulphide and non-sulphide minerals often cause PGM losses. When silver ore contains significant amounts of pyrargyrite, proustite and stephanite, silver recovery by cyanidation can be very low because of the slow dissolving kinetics of these minerals. In the processing of base metal ores, high content of pyrite, intergrowth of chalcopyrite with sphalerite and presence of clay miner-als may cause problems in recovering Cu-, Pb- and Zn- bearing minerals. Process mineralogy helps address all issues and problems related to mineral processing with predicting and trouble-shooting being two major objectives. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. The information acquired from a process mineralogical study can be used as a guide for a metallurgical testwork program for process design or optimization.

Jan 1, 2014