Search Documents

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By Haragobinda Srichandan

The present study aimed to investigate the bioleaching efficiency of moderate thermophilic microorganism in a growth medium without Fe supplement on three different size fractions of spent catalyst obtained from petroleum refinery. All the experiments were conducted on shake flasks at a temperature of 65 °C and a pulp density of 10% (w/v) on three size fractions viz. 45-106 µm, 106-212 µm and >212 µm and a working volume of 100 ml comprising of 10 ml of microbial inoculums and 90 ml of Modified Kelly medium. The parameters like pH, redox potential, viable planktonic cell count and the amount of acid addition was measured and quantified on regular basis to follow the progress of the bioleaching. The pH varied much in the lag and logarithmic phase of the experiments but stabilized toward the stationary phase. The total acid additions in each batch experiment were determined the amount of Conc. H2SO4 requirement, which ranged between 683-757 kg/ton of spent catalyst. The redox potential values ranged between 625-650 mV, Ag/AgCl, but were very low ranging between 350-450 mV during initial period. The planktonic viable cell count ranged between 108-109 cells/ml active in the bioleaching system, without any toxic influence of the spent catalyst, but initially due to fall in redox potential and new environment for the microbes, their population was low. The leaching yield of Ni was found to be promising with very high leaching yield of 92-96% followed by Al as 61-62%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. There was very little difference in the leaching yield, when compared with different size fractions and hence grinding can be avoided prior to leaching. This process seems to be economical as no Fe source is supplemented together with no requirement of grinding and over all a biological process resulting for an eco-friendly process for future optimization of the metal recovery from petroleum refinery spent catalysts. Keywords: bioleaching, spent catalyst, thermophile, 9K medium

Sep 1, 2012

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By Stoyan Groudev

Two experimental plots consisting of a slightly acidic soil heavily contaminated with radionuclides (mainly uranium and radium) and non-ferrous metals (mainly copper, zinc, and cadmium) were treated in situ under real field conditions using the activity of some representatives of the indigenous soil microflora. This activity was enhanced by suitable changes in the levels of some essential environmental factors such as pH and water, oxygen and nutrient contents of the soil. The treatment was connected with solubilization and removal of the contaminants from the top soil layer (horizon A) due to the joint action of the soil microorganisms (mainly acidophilic chemolithotrophic bacteria) and leach solutions (diluted sulphuric acid) used to irrigate the soil. In one of the plots, the dissolved contaminants were removed from the soil profile through the drainage soil effluents and were subjected to cleaning by a constructed wetland located near this plot. In the other plot, the dissolved contaminants were transferred to the deeply located soil subhorizon B2 where they were precipitated as the relevant insoluble forms (uranium as uraninite, and the non-ferrous metals as the relevant sulphides) as a result of the activity of the sulphate-reducing bacteria inhabiting this soil subhorizon. This activity was enhanced by injecting water solutions of acetate, lactate, ammonium, and phosphate ions to this soil subhorizon.

Sep 1, 2012

By Diana Drinkwater

As ore grades decline, ore deposits get harder and mineralogical complexity increases, metallurgical skills are more important than ever to ensure that today?s mining operations are operating efficiently and profitably. Yet specialist undergraduate degree programs have all but disappeared and metallurgical skills training for graduate engineers in the workspace if often haphazard. In response to this situation, specialists at the JK Centre in Queensland, Australia, have put together a professional development program designed to fast-track skills development for early career metallurgical professionals. The program, called ?MetSkill ® ?, is offered as a group training package for young metallurgists in the workplace. It is centred on a meaningful technical investigation negotiated between the JK Centre delivery team and the client company. As well as learning about project management and data collection and analysis, the participants study specialist topics such as comminution, flotation and mineralogy under the tutelage of senior research and consulting professionals. The technical investigation provides an opportunity for immediate practice of these new skills and JK Centre specialists are on hand to provide feedback and support throughout the program. The participants are employed across different operations in Australia and the Asia-Pacific, and although they occasionally come together for group training activities they are often separated by considerable distance. Specialist educational professionals from The University of Queensland have provided an innovative web platform to support collaboration and communication between all participants. This paper will describe the MetSkill ® program in detail, as well as providing a report on its initial roll-out to 2 groups of Australian graduate metallurgists in 2012

Sep 1, 2012

By ?. S. Yusupov, V. P. Isupov, N. Z. Lyakhov, A. G. Vladimirov, S. A. Kondratiev

"Considering the shortage of lithium reserves, the desirability has been shown of studying the possibility of processing into spodumene concentrates the concentration tailings and low-grade ore reserves at Transbaikalian Mining and Processing Project (ZabGOK). The mineral and chemical composition and the particle size distribution of the mineral feed, separability and recoverability of spodumene have been studied, forming the basis for the development of a concentration process and flowsheet for the studied mineral resource. Prospects have been established for impact ore grinding in a disintegrator, the efficiency of mechanochemical processes has been shown in the separation of quartz and feldspar and the recovery of lithium from concentrates.INTRODUCTION Lithium is widely used in various industries - nuclear power engineering, defense technology, power generation, ceramics, special-purpose glass and other technologies. The increasing demand for lithium and its compounds (lithium carbonate and hydroxide) for use in the manufacture of high-tech products (lithium-based materials for chemical sources of electric power and electrochemical energy) explains the need for establishing a sustainable raw material base (Mohr et al. 2012; Moores, 2007). The main sources of lithium are spodumene pegmatites (Vladimirov et al. 2012; Garret, 2004), brines (salars), and hydromineral materials (Garret, 2004; Zeng and Liu, 2009; Kotsupalo and Ryabtsev, 2008). However, in view of the absence in Russia of extractable hydromineral resources of lithium, the practical significance of spodumene ores remains decisive. Russia controls some of the world’s largest reserves of rare-metal pegmatites holding over 8 million tons of Li2O: approximately 7 million tons on the Kola peninsula and 1 million tons in the Sayan mountains. The main lithium mineral in pegmatites is spodumene LiAlSi2O6 containing 8.1% Li2O. It can be efficiently recovered by gravitational concentration and flotation. However, most of the deposits are located in remote areas and none is currently developed. In this connection, special research is focused on technogenic raw materials, which are increasingly seen as a solution to the resource base problem (Chanturia, 2008, Kurkov and Kotova, 2007)."

Jan 1, 2018

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

By Carolina Achiardi, Álvaro Videla

"In pre-design a flotation plant copper sulphide is useful to apply a simplified methodology of economic analysis that relates the size of the grinding product (P80) with the throughput and their effect on copper grade and recovery of copper in the final concentrate of a flotation circuit. With this objective, this methodology covers the following analysis, perform by evaluation of five sizes grinding products (P80): 120, 150, 180, 210 and 240 microns. • Flotation testwork (rougher kinetic, open and closed cycle test) has been done to determinate the optimum operating conditions and to estimate the maximum recovery of copper in the concentrate, using Klimpell model • Flotation plant design assumes a conminution product obtained from a 25,000 HP ball mill • Metallurgical balance is performed for the circuit based on flotation testwork • Economic evaluation by calculating capital expenditure (CAPEX), operating expenditure (OPEX) and sales revenue, to determine NPV is performed and relates to the NPV. An optimum grind size is then obtained based on cash flow. The results shows a grinding product size that optimizes flotation and allows a higher NPV and INPV over other alternatives."

Jan 1, 2014

By J. Menuge, G. Barker

"Liberation (QEM-SCAN) and surface chemical (time of flight secondary ion mass spectrometry -ToF-SIMS) analyses have been undertaken on plant Pb circuit flotation samples with the aim of defining the factors resulting in sub-optimal recovery. Lead flotation circuit feed, cleaner concentrate and tails samples were examined on a size-by-size basis using QEM-SCAN. Sulfide minerals accounted for approximately one third of the flotation feed with pyrite making up 16 wt.%, followed by sphalerite (13 wt.%) and galena (3 wt.%). Non-sulfide gangue minerals comprised calcium carbonates calcite (26 wt.%), dolomite (14 wt.%) with quartz, feldspars and barite all contributing > 5 wt.%. QEM-SCAN analysis indicated that liberation was not the primary cause of the poor flotation response. Principal component analysis was applied to the ToF-SIMS data derived from five samples (as for QEM-SCAN plus rougher concentrate and tails) to enable identification of correlated surface chemical components. Although a significant range of correlations were observed we focus here on those that show a discernible pattern throughout the float circuit. It was found that for the flotation feed the surface of galena were largely obscured but where Pb was observed there was a strong correlation to surface Fe. For the rougher and cleaner concentrates the galena surfaces were relatively clean with no correlation to Fe for the rougher concentrate and minor correlation in the cleaner concentrate. However, in the rougher and cleaner tails the clear correlation of galena with Fe was again apparent. These results suggest, in combination with prior studies of pyrite morphology, that the principal factor effecting grade is the rapid oxidation of the framboidal pyrite resulting in the contamination of the galena surface with a high loading of hydrophilic oxidised Fe species, thus depressing flotation."

Jan 1, 2014

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By S. J. Dai

The cadmium and cyanide are main poisonous components in cyanide electroplating cadmium waste water of an electroplating plant in Shenyang. The content of cadmium is about 26 mg/L and the content of cyanide is about 11.782 mg/L in this waste water. The main form of cadmium and cyanide are ions which are Cd2+and CN?. Because the cadmium and cyanide exceeded the standard seriously, the waste water must be disposed before it discharges. The microbiological method of treating heavy metals in wastewater has many advantages. For example, it has a fast adsorption velocity, high processing efficiency, wide range of pH and temperature, few invest, low running cost, no the second pollution and so on. At the same time, the CN? could be degradated by some microbiology. The physical nature, the chemical nature of Bacillus mucilaginosus, the adsorbing condition and adsorbing regular of Bacillus mucilaginosus to cadmium in the wastewater are studied by using Bacillus mucilaginosus as adsorbent removing cadmium from electroplating wastewater. The experimental results show that the adsorbing rate of cadmium is over 92%, under the room temperature(about 25?), stiring revolution in adsorption being 800 r/min for 30 min, pH being 5 , the bacteria being cultured after 5d with the biomass of Bacillus mucilaginosus 40g/L (wet weight). The mechanism in biosorption process of Bacillus mucilaginosus to cadmium is analyzed and discussed by TEM , Zeta potential,and infrared spectroscopy analysis. The results showed, the chemical involving is main adsorbing form, while electrostatic attraction, ions exchange, hydrogen bonding and Van Der Waals force are concerned cooperatively. ?NH2 ?, ?C=O?, ?C=O?NH?CH2, ?CH3, ?OH are main adsorbing groups. At the same time, the floatablity of removing cyanide by Bacillus mucilaginosus is explored.

Jan 1, 2014

By A. Bahrami

Andalusite, silimanite and kyanite are polymorphs of aluminosilicate known as kyanite group. Minerals of this group are used in refractory. Sarband andalusite deposit is located in Markazi province in Iran. Mineralogical studies showed that the main minerals of this sample are andalusite (5%~10 %), mica, quartz and feldspar. Processing of the samples was carried out using two sizes, i.e. +500 µm and -500 µm. In the processing of +500 µm scrabble test was carried out on -4750 +500 µm and -2380 +500 µm. For -500+300 µm shaking table and magnetic separation were applied. For -300 µm fraction, flotation was carried out. The results of this tests showed that the processing of Shazand andalusite was not possible, because silica and iron impurities were diffused inside the andalusite mineral grains.

Jan 1, 2014

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"The effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases.Electrokinetic methods were used to elucidate the mechanism of surfactants adsorption and to correlate these findings with the optimum flotation conditions. The polymeric surfactants would reduce the negative values of zeta potential of quartz while the reverse is true for feldspar. After treatment of microcline with HCl, its electrokinetic behavior in the presence of Tritons X surfactants became similar to that of quartz.The obtained results would suggest that separation of quartz from feldspar using nonionic surfactants of octylphenoletoxylated alcohols having shorter oxyethylenic chain length at low pH could be achieved"

Jan 1, 2003

By B. Y. M. Bueno

Biosorption of heavy metals can be an effective process for the removal of heavy metals ions from aqueous solutions. In this study, the adsorption properties of Rhodococcus opacus biomass for Pb(II) and Cu(II) ions was investigated. The effects of initial pH, initial metal concentration and biomass concentration on biosorption efficiency were studied in a batch system. Results showed that the initial pH would play an important role in the Pb(II) and Cu(II) ions removal by R. opacus and affected the zeta potential of R. opacus. The equilibrium adsorption was reached with 60 min. The Langmuir and Freundlich models were used for describing of adsorption isotherm data. The maxi-mum adsorption capacities of biomass were determined as 94.3mgg-1 and 32.2 mgg-1 for the Pb(II) and Cu(II) ions, respectively. The experimental data fitted to pseudo second order kinetic model. Adsorption capacity of Pb(II) ions was found to be reduced by the presence of the other competing metal ions in the system. The FT-IR results of R. opacus biomass showed that biomass has different functional groups and these groups are able to react with metal ions in aqueous solution.

Jan 1, 2014

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

In flotation, particulate materials are separated by controlling the hydrophobicity of the particles using appropriate collectors. In this regard, contact angle (?) is the most important process variable. However, the flotation models used in industry today do not include ? as a parameter. As result, flotation circuits are designed based on the first-order flotation rate constants (k) determined from laboratory experiments. A problem with this approach is that laboratory experiments usually give substantially higher k values than achievable in full-scale operations, which makes it difficult to use the model for plant design. In the present work, we have developed a model from first principles using both surface chemistry and hydrodynamic parameters, such as ?, ?-potentials, surface tension (?), particle size, energy dissipation rate, etc. The basic approach is similar to the one developed previously for bubble-particle interactions under laminar flow conditions (Yoon and Mao, J. Colloid and Interface Science, 181, 61, 1996) except that the model parameters have been modified by considering the turbulence in a flotation cell. In addition, the model describes the recovery processes in froth phase, including bubble-coarsening due to coalescence. Based on this model, we have developed a computer simulator (FlotSim) that can be used to design flotation circuits from the mineralogical (or liberation) data on the feed and the hydrodynamic characteristics of a flotation machine. Since the model is dynamic, it can also be used for process control. Further, the simulator has predictive capacity as it is based on a first-principles model. The model-based simulator has been validated in a carefully controlled bench-scale flotation experiments. Keywords: flotation kinetics, flotation model, contact angle,?-potential, size-by-size recovery, liberation, DLVO theory

Sep 1, 2012

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By F. N. Shi

Ore breakage characterization plays an essential role in the design and optimization of comminution circuits. Recently, the JKMRC comminution research team has developed a Rotary Breakage Tester (JKRBT). The JKRBT uses a rotor-stator impacting system, in which particles gain a con-trolled kinetic energy and are impacted against the stator, causing particle breakage. The first unit of industrialised JKRBT was installed at the Anglo Research in South Africa in March 2007, and five more JKRBTs are currently being fabricated for some of the world?s major mining companies. In addition to the JKRBT, an improved breakage model has been developed at the JKMRC, which more accurately describes the effect of specific energy, particle size and incremental breakage caused by repetitive impacts. The validation outcomes show that the JKRBT, together with the new breakage model, generate statistically similar breakage parameters to the traditional drop weight tester (DWT), but with significant advantages over its predecessor. The limitations of the DWT, specifically its lack of precision of the energy input, the lengthy time required to run individual tests and the challenges en-countered in testing small particles, have all been overcome by the JKRBT. The recent developments in the JKRBT and the new breakage model offer several prospective applications. These developments have the potential to revolutionize the ore breakage characterization in the years to come.

Jan 1, 2014

By S. I. Anufrieva, N. A. Permyakova, E. G. Likhnikeevich

"Russia’s rare metal reserves are composed of compositionally and structurally complex ores and are characterized by an increased content of natural radionuclides due to their geochemical similarity with rare metals. For instance, concentrates of Zashikhinsky daeposit are characterized by an increased content of uranium (0,06%) and thorium (0,59%); Beloziminsky deposit holds pyrochlore-apatite-magnetite-carbonate ores characterized by increased radioactivity (130 mkR/h) and containing 0,0016-0,0025% of uranium; Etykinsky deposit is characterized by columbite-pyrochlore-microlith mineralization with an average ore grade of 0,013% of uranium and 0,0020% of thorium; eudialyte concentrate of Lovozero deposit (Alluaiv area) belongs to Class II of mineral reserves. Industrial development of these mineral reserves involves the need to comply with environmental standards, public health requirements applicable to finished core and by-products, to take into account the amount and class of the generated radioactive waste, the possibility of disposal or recycling of the radioactive production waste. Concentration processes of radioactive rare metal feeds most often lead to a concentration of natural radionuclides and their accumulation in concentrates. Comprehensive hydrometallurgical processes are currently under development for such concentrates, aimed at producing salable products compliant with the radiation safety standards. The choice of the hydrometallurgical processing method for radioactive rare metal concentrates is based on the mineralogical component of the concentrate, textural and structural features, the distribution of valuable components and impurities, and the content of radionuclides. A systemic approach to the selection of processing methods, in particular integrating several methods, is an effective solution. Methods may not only be combined, but also inextricably linked with each other. Hydrometallurgical processing methods include leaching by acidic and alkaline agents; sulfatization for selectively decomposing the minerals and moving the bulk of U and Th into solution; fluorine extraction process. Methods of precipitation and co-precipitation, extraction (by liquid and solid extractants), sorption, and ion exchange are used to decontaminate the solutions by removing thorium, mezathorium, uranium, and their radioactive decay products. Agents used in hydrometallurgical processing of radioactive rare metal ores include sulfuric, nitric, hydrochloric, hydrofluoric acid, alkali (NaOH, KOH), sorbents (for example, AB-17) for sorption of uranium and extractants (mono- and bidentate organophosphorus compounds, diamides, etc.) for the extraction separation of rare, rare-earth, and radioactive elements."

Jan 1, 2018