Search Documents

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

By Don Deardorff, Ke Yang, Yingcai Han, Ken Sorensen, Robert Kruger, Mark Petersen, Diane Fiorelli, Larry Goldfarb, Kathryn Petek, Kwabena Ofori-Awuah

Design of deep foundations for lateral loads requires an understanding of soil-foundation-structure response during loading. Lateral loads on a deep foundation (piles) could be due to earthquakes, winds, waves, and/or machine vibrations. Over the years, analysis of response of piles due to lateral loads evolved from closed-form solutions to p-y methods to strain wedge to finite element/finite difference modeling. Although analysis of lateral response of piles and shafts is routinely performed, there is no single guidance document and/or standard for design and testing. Several different analytical methods are available for the analysis, and the resulting design can result in significantly different responses which can create confusion. This is especially true for analyzing and designing piles in potentially liquefiable soils with lateral spread issues under seismic conditions.This guidance document is intended to assist geotechnical engineers, pile designers, and contractors in analysis, design, and testing of piles and drilled shafts for lateral loads. This document discusses the background of different analytical and testing procedures and presents the recommended methods for analysis, design and testing of piles for lateral loads.Chapter 1 defines the different kinds of lateral loads to which a single pile or pile group may be subjected. This first chapter also presents different types of piles used to resist lateral loads.Chapter 2 discusses geotechnical issues related to lateral pile design such as liquefaction and lateral spreading and other non-seismic issues. Also addressed in Chapter 2 is geotechnical site characterization (as related to lateral loads) in terms of site investigation, in-situ testing, geophysical testing, laboratory testing, and estimation of soil/rock properties.Chapter 3 discusses the background and available analytical methods and tools for the analysis and design of single piles and drilled shafts. Several methods of analyses from closed-form elastic solutions to the finite element/finite difference solutions and their applicability are discussed. Available commercial computer software packages for analyzing single piles and drilled shafts are also presented.Chapter 4 expands the discussion of single piles and drilled shafts into the analysis and design of pile groups. In addition, group effects, resistance of pile caps, results of previous experimental and analytical studies, and available analysis tools and software for pile groups are discussed.Chapter 5 presents the issue of lateral resistance of piles and drilled shafts as discussed in different national and international building and non-building codes. A summary of extensive research on several codes are presented to facilitate the compliance with different codes.Chapter 6 discusses structural design issues of individual piles and drilled shafts such as depth of fixity.Chapter 7 discusses soil structure interaction issues related to kinematic and inertial effects due to seismic loading and available methods of analyses.Chapter 8 discusses and presents the typical procedures for the lateral load testing of piles. This guideline was developed as an aid to the practicing engineer in providing information, direction and commentary on the lateral design of deep foundations. Although all reasonable effort has been made to accurately compile the material and information contained herein, no warranty is made with regard to any such material or information and the Deep Foundation Institute assumes no responsibility for any possible errors or any direct or indirect result of the use of any such material or information. It is not intended that this document address every factor affecting lateral design for every situation. Therefore it is the responsibility of the person utilizing information from this document to confirm that it is appropriate and correct for their situation as well as to understand and properly apply

Jan 1, 2012

By Maurice Bottiau

The recent evolution of the piling market clearly shows a growing demand for screw piles with soil displacement. The recently developed Omega Screw pile ful-fill these new expectations, combining the advantages of vibration-free systems and the behaviour of a displacement pile. The paper describes recent experience and new applications with this very promissing pile. Full-scale load tests were carried out in different countries as U.K. or Sweden. A very attractive and innovative piled embankment is also described, using geogrids in order to transfer the loads from the superstructure to non-reinforced Omega-piles.

Jan 1, 1996

Jan 1, 1992

By Walter E. Vanderpool

Three drilled foundations for an elevated water-tank were instrumented, tested and monitored during construction and the first two years in service. One shaft was load tested by the Osterberg method. A void was detected in one shaft by cross-hole sonic logging, pulse-echo logging and concrete coring. The void was instrumented, hydrostatically tested and pressure grouted. The shaft was ?abandoned? and replaced by two smaller shafts with a straddle beam cap. One of the replacement shafts and the cap were instrumented. The strain that appeared in the abandoned shaft, the replacement shaft and the cap were monitored during the remainder of the construction, through the commissioning test and the first two years of service. The results demonstrate the precision and sensitivity of the vibrating wire strain gage.

Jan 1, 2004

By Marlion T. McQuinn

This paper will discuss the design, construction, and performance of the support of excavation on the Dulles East and West Automated People Mover Tunnels and Station projects. The elements of the system included drilled soil nails and rock anchors with reinforced shotcrete to the excavated face. We will discuss the geotechnical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the support of excavation system. In consideration of the conference theme, there will be a discussion of the application of the real-time instrumentation monitoring program. The project team worked to design and install approximately 710,000 square feet of shotcrete and 19,000 soil nails/rock anchors as well as excavate over 720,000 cubic yards of rock materials within 15 months and in such a manner as to minimize the disruption to airport passengers and operations.

Jan 1, 2006

By B. H. Moore

The opportunity to evaluate the pile design procedures used on a major project is an infrequent occurrence. It is even more infrequent that the project involves piles with significant tension and horizontal capacities. This report synopsizes over twenty years of design and construction experience on just such a major pile founded structure. The philosophy governing foundation design procedures is described and discussed. The order and extent of full scale pile testing are evaluated. Principal points in the specifications are established and their effect on construction progress and claims are noted. The report concludes with recommendations for future projects.

Jan 1, 2010

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Fabio Santillán, Mario Mauro, Raffaella Granata

"This paper presents the utilization of slurry walls methods for the recent remediation of three high hazard active dams in the United States. Tuttle Creek Dam, located in Manhattan, KS, required seismic retrofit. To this extent, transverse shear walls were installed on the downstream slope using self-hardening slurry (SHS) to reinforce the liquefiable foundation soils. Herbert Hoover Dike, located around Lake Okeechobee, FL, is subject to potential failure because of internal erosion, piping and slope instability at high water levels. The innovative use of the hydromill equipment with SHS allowed the successful construction of the cutoff wall through heterogeneous soils and rock. At Bolivar Dam, located in Bolivar, OH, under-seepage negatively affects the structural stability of the dam, and a partial seepage barrier wall is required through the upstream slope of the dam. In this case, the Contractor selected the plastic concrete seepage barrier, excavated by a combination of clamshell and hydromill equipment. The main features of the three projects are summarized in Table 1. IntroductionTuttle Creek Dam was constructed by the U.S. Army Corp of Engineers (USACE) on the Big Blue River in North-East Kansas in the 1950s for flood control. Tuttle Creek Dam is a zoned earthfill embankment, 7,500 ft long and about 137 ft high with a crest width of 50 ft (Fig. 1). It is located in an area of moderate seismicity associated with an old continental rift zone located just to the east of the dam. The USACE, under the Dam Safety and Assurance Program, determined the need for remediation. Site investigations and geotechnical analyses identified the upper alluvial foundation sands as being susceptible to liquefaction when subjected to the Maximum Credible Earthquake.In 2005, USACE awarded a construction-manager-at-risk/early Contractor involvement contract. The USACE and the Contractor closely cooperated to identify the most effective technologies, materials and configurations to be used in the remediation. The original remediation design required both the upstream and downstream slope stabilization of liquefiable foundation. Results of refined seismic deformation analyses revealed that the stabilization of the downstream slope and toe was needed to protect the downstream seepage control system and to provide assurance that a liquefaction-induced flow slide would not occur (Stark et al., 2012)."

Jan 1, 2016

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

Jan 1, 1997

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

This Workshop was held at the Doubletree Inn, Seattle, Washington from September 26 to 28, 1997. Run under the auspices of the Deep Foundations Institute (DFI), it was co-funded by the newly formed Japanese Association of Micropiles (JAMP), and the Federal Highway Administration (FHWA). The Workshop was jointly organized and facilitated by Fujita Research Corporation and ECO Geosystems, Inc., with close support by Donald B. Murphy Contractors, Inc. DFI kindly consented to publish these Proceedings. As is clear from the list of attendees, 42 specially invited engineers from all aspects of micropile technology were present, representing Japanese, European and American practice. This proved to be a most friendly and interactive group of people, who freely exchanged ideas, views and close comradeship, not only during the technical sessions, but (and especially!) during the numerous social events. Perhaps the best illustration of this came in Day 2 when the attendees were divided into five competing teams, each comprising representatives from the different geographic groupings. These teams had to quickly devise solutions to two technical problems (using standard data previously provided. A team of "referees" (who also acted as "coaches") later determined the most apposite response, based on constructability design concept, cost, schedule and so on. Not only were the winning team very liberal in distributing the prize (vintage California champagne) among themselves, but the whole Workshop soon benefited from their generous division of the spoils of victory.

Jan 1, 1997

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000