Search Documents

By Rafael A. Rivera

"Since the dawn of construction, there has been a need for excavations, which sometimes need to occur below the groundwater table. Excavations in themselves are difficult enough, with the myriad of requirements, such as engineered support of excavations, considerations for stability and numerous other concerns. Excavations executed in rural landscapes can be accomplished easily without significant consideration to accessibility, adjacent properties or structures, and construction limits and deformations. However, all of these factors can have an impact on excavation considerations in an urban landscape. When digging below the groundwater table, these conditions, along with concerns associated with groundwater drawdown requirements, discharge limitations, groundwater contamination, property limits, adjacent buildings and subsidence concerns, can lead an experienced dewatering contractor to consider diverse installation methodology and equipment to allow construction to occur below the groundwater table.534 W. 29th St. New York, N.Y.There are many things that must be considered when constructing a new high-rise building within a small property footprint measuring 25 ft (7.6 m) wide by 80 ft (24.4 m) in length. When you take into account that the foundation needs to go several feet below the groundwater table and that there are two existing multistory buildings with shallower foundations on either side of the proposed structure, this task now becomes much more difficult. Consideration of geology, groundwater levels, depths of excavation and shoring for the excavation becomes critical to the success of the project. On a regular basis, dewatering contractors confront similar situations in congested cities where available real estate is limited.To minimize the negative impacts of construction dewatering, it is important to mitigate the potential effects of construction dewatering to the surrounding buildings, sidewalks, underground structures, tunnels, subways and other existing infrastructure. Such an instance occurred at the project located at 534 W. 29 St. in New York City. On this particular project, the required drawdown was greater than the typical 15 ft (4.6 m) of suction lift, so a vacuumed can pump system was utilized. The tubing was connected to a vacuumed perimeter dewatering well-point system, which is a predrainage system that is installed prior to the start of excavation for the underpinning of the adjacent structures and for the overall foundation. Each well-point, which was composed of a PVC pipe that was 1.5 in (38 mm) in diameter by 25 ft (7.6 m) long, was drilled to a depth of about 23 ft (7 m) using a hollow stem auger and was installed around the perimeter at a centerto- center spacing of about 7.67 ft (2.3 m). In lieu of a traditional perimeter collection header, and to allow for greater flexibility for the contractor, the well-points were interconnected to a modified vacuum can pump system utilizing ¾ in (19 mm) drop tubes that were “spaghetti” around the perimeter."

Jan 1, 2017

By Jerry A. Steding

How many times have you heard "You can't drive piles because of the vibration."? You hear these words come out of the mouths of owners, engineers, and contractors. When a piling contractor hears this, he can almost always do a psychological profile of the individual uttering these words of wisdom. If the owner makes the statement, we know the odds are about 95% that the owner owns the building next door or he wouldn't care what happens to it; or the guy next door has threatened to sue the owner if he even so much as walks across the site of the proposed new building. If the owner owns the building next door to the new construction you can also be just as certain the old structure has undergone settlement. If the statement comes from the mouth of the contractor, it is usually just a case of him being inexperienced.

Jan 1, 1988

By H. (Sam) Salem

A site investigation for a wide and tall hotel building, in the San Juan Bay area, Puerto Rico, indicated a soil profile of silty clay on sand, soft and loose enough to require piled foundations. The apparent uniformity of the soil profile across the site indicated that a single pile driving and termination criterion could be applied to the installation of the piles ? driven precast concrete piles. Because of the size of the site and importance of the project, the project also included a static and dynamic testing programme. The dynamic monitoring using the Pile Driving Analyzer (PDA) verified a consistent hammer operation. However, the results of the static loading tests showed significant and inconsistent variation in pile capacity between locations and little correlation between end-of-driving and restrike penetration resistances (blow-counts) and pile capacity. Therefore, it was not possible to rely on a simple depth and blow-count termination criterion for the site. In contrast, pile driving response in terms of measured reflected force and mobilized resistance coupled with CAPWAP analysis gave a reliable correlation to the results of the static loading tests. As presented in the paper, the dynamic testing programme was enlarged and used to develop and verify a complex set of termination criteria tailored for the multitude of conditions encountered across the site to achieve and ensure economical and safe pile installation.

Jan 1, 2008

By Andrew Budek

"Analytical and experimental work has shown that achieving the full inelastic lateral capacity of a pile may require the formation of a plastic hinge below ground level, in the pile shaft. The confining action of soil about the pile shaft was further been shown to greatly enhance the ductility capacity of the pile. An experimental program was therefore undertaken to build in the effect of external confinement through the addition of a GFRP jacket to the subgrade plastic hinge region. Two piles were thus modified, and compared to an unjacketed pile in a test rig which simulated a subgrade moment pattern and soil confinement. The ductility achieved by the jacketed piles was found to be substantially lower than an unjacketed control specimen. Failure mode of the jacketed specimens was also undesirable, involving complete tendon rupture and sudden loss in capacity IntroductionSeismic loading of concrete pile shafts can result in a demand for inelastic response. In the case of a superstructure supported by a single pile (i.e., a pile-column forming a single-column bridge pier, in which there is no rotational restraint at the top of the pile}, a plastic hinge will form below grade, at a depth which varies with soil properties and above-grade height of the center of seismic mass.In the case of a superstructure supported by multiple piles, there is rotational restraint, and the connection will experience inelastic action first. However, development of the full lateral inelastic capacity of the pile may call for the formation of a second, subgrade plastic hinge (fig. 1 )."

Jan 1, 2005

By Michael Arnold, Robert Bachus, Michael Bracher, Jamey Rosen, Robert Roff

"For a high hazard USACE facility, the Center Hill Dam in Tennessee, several disparate streams of data were compiled into a single geospatial and relational enterprise data management system to store, analyze, visualize and distribute the data collected during installation of a deep cutoff wall. These data streams included historical drawings and pre-construction plans and grouting records; geological data from boreholes; attributes of barrier wall elements; element verticality data analyzed from multiple measurement methods; and concrete field and laboratory analytical data. A previously developed data management system developed by the authors, WallTracker, was extensively modified to also include manually collected and real-time measurements from several types of dam monitoring instruments. The system now uses enterprise database technologies with Geographical Information Systems capabilities to manage and relate these data streams into a common platform and allows access to the raw and interpreted data via web and desktop-based interactive tools, including interactive map and cross-sectional viewers and other graphical and tabular reporting tools. One of the primary benefits of this system is the neartransparent interaction that is possible with the Nashville District of USACE on the project. These techniques can now be effectively incorporated into systems that address the unique construction and data management tracking requirements for dams, dikes, and levees.IntroductionThe Center Hill Dam rehabilitation, as with other deep foundation installations, requires the contractor to collect a substantial amount of information over the course of the project, both for internal quality control of construction progress and methods, and for demonstrating compliance with owner specifications. This paper discusses techniques used at Center Hill Dam for consolidating, visualizing and analyzing construction and instrumentation data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as an Information Management System (IMS).The remainder of this paper presents the needs and objectives of the IMS, the components and data flows involved, the capabilities and user interfaces of the systems, and the benefits for the end users."

Jan 1, 2017

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Terence P. Holman

Micropiles are employed to retrofit existing foundations, including underpinning prior to future construction operations and resupport of existing structures that have experienced distortion and settlement. This paper presents analyses of the two case histories requiring the use of micropiles in these applications. The first case history involves micropiles used to resupport a settled pump station next to an excavation which had suffered basal failure and ground loss. A compression load test pile experienced plunging failure which, after analysis of the strain-gauge data acquired during the test, was attributable to a greater degree of disturbance to the subsoils beneath the site than anticipated. After construction of the micropiles around the pump chamber a synchronized jacking system was used to lift and right the 320 kip chamber structure, followed by resupporting it on the newly constructed piles. The second case history entails the use of micropiles for direct underpinning support of existing columns prior to a utility tunnel installation within an existing high-bay warehouse structure. The design constraint that most significantly affected the successful completion of this project was the desire to bond the new piles into the existing reinforced concrete foundations. As a result of the coring method through the footing, the ultimate bond stress measured during a pullout test was more than twice that assumed in the design. Monitoring of the underpinned columns during trench excavation indicated that the system performance was acceptable. These case histories reinforce the concept that lower capacity micropiles can provide a rapid means to underpin and retrofit existing structures.

Jan 1, 2007

By Mousaab Majar, Nikolaus Schneider

The technical challenges for accurate drilling positions increase with deep underground structures in inner city areas. Designed for jet grouting, specific sensors have been developed to record the alignment of rods during drilling by integrating microchips into the drilling rods. By feeding the rod with constant electric current, microchips, integrated in special couplings, can be read during the drilling process and tracked on monitors installed in the operator’s cockpit. The orientation for the drilling rod is provided by magnetic points and a compass, positioned above ground on the drilling rig. In combination with asymmetric drilling bits, it is now possible to steer the drilling hole to predetermined positions to compensate for deviations in deep bores. This type of drilling rod for jet grouting has been used in Berlin since summer 2019.

May 1, 2022

By Sung-Ryul Kim, Woong-Jong Park, Juhyung Lee, Si-Hoon Lee

"A bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In this study, a series of 1-g model tests were performed to analyze the accumulated rotation of suction bucket foundations under long-term cyclic horizontal loads. The model suction buckets were made to have the embedment ratios of 0.5 and 1. The dry model ground was prepared to have two different soil densities by air-pluviation method. A horizontal cyclic load over 104 cycles was applied varying the loading amplitude. Test results showed that the accumulated rotation of the bucket foundation increased with the increase in the number of cycles and load magnitudes. Based on the model test results, a new equation was proposed to evaluate the accumulated rotation of the bucket foundations in sandy ground under long-term cyclic horizontal loads.INTRODUCTIONRecently, a bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In terms of economy, a bucket foundation has been considered to be an economical foundation type at sea beds where ground condition is clay or medium dense sand.A bucket foundation resembling a bucket is a kind of suction-installed foundation units. It is a skirted steel foundation which is open at the lower end and closed at the upper end by a lid. The embedment depth ratio (L/D) of a bucket foundation is usually less than one. Figure 1 shows an example of a bucket foundation. Offshore wind turbines are subjected to long-term cyclic loading by wind or currents. A bucket foundation is installed in soil grounds, so the long-term cyclic loading may induce the accumulation of soil deformation.In this study, the accumulated rotations of the bucket foundations in sandy ground were investigated under long term cyclic horizontal load. The number of cycles up to 104 cycles was applied varying load magnitude. The accumulated rotations of the bucket foundations in sandy ground were analyzed based on the test results."

Jan 1, 2016

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Mikael Calando, Thomas Joussellin

"San Francisco's rapid growth has caused the city to plan for the Transbay Transit Center Project, a visionary transportation and housing project, that will transform downtown San Francisco and the San Francisco Bay Area’s regional transportation system by creating a “Grand Central Station of the West” in the heart of a new transit-friendly neighborhood that will be home to more than 20 new towers rising a high a 1,070 ft. This paper describes the specificities of using advanced diaphragm wall technology, tooling, equipment and installation practices for deep foundation and permanent underground structures. In particular, this paper will emphasize on the urban constraints, geotechnical conditions, and the novel approaches adopted for the construction challenges of the Transbay Transit Center’s Load Bearing Elements, or Barrette PilesPaperThe Transbay Transit Center Project consists of the construction of a new multimodal, five-story Transit Center located in the South of Market neighborhood near the Financial District in San Francisco. The future Transit Center will incorporate nearly 83,000 square feet of retail, a 5.4-acre rooftop park, an extensive public arts program and bus ramps that will connect the Transit Center to a new off-site bus storage facility and the San Francisco–Oakland Bay Bridge. The new facility will accommodate more than 100,000 passengers each weekday and up to 45 million per year. Additionally, the new Transbay Transit Center will replace the since-demolished San Francisco Transbay Terminal, and nearly 20 towers, such as Salesforce Tower, will take advantage of the height increases allowed through the Transit Center District Plan.The approximately $4.5 billion project features a new five-story structure (including two underground stories) and new bus ramps which include a cable-stay bridge. The deep foundations for the pylon of the bridge (Pylon 9) consist of two each 21 ft x 5 ft barrettes (also called Load Bearing Elements in the US) extending more than 180 feet below grade and 10 feet into the bedrock. The barrettes were chosen because of the combination of high loads, significant depth and small footprint. The barrettes are installed using the Diaphragm Wall technology. Nicholson Construction was contracted by Shimmick Construction to install the cable-stay bridge’s foundation elements."

Jan 1, 2016

By Spencer Ness, Yazen Khasawneh, William Tjaden, Mohammad Nassim

The evaluation of long-term performance of the wind turbine structures is essential in lowering the Levelized Cost of Electricity (LCOE) from wind sources. The required maintenance of the wind turbine foundation during the design-life time of the wind turbine may result in escalated cost, if not properly evaluated during the planning and designing phases. The degradation of the foundation soils’ stiffness due to the accumulation small plastic strains resulting from normal and/or extreme operating cyclic loading may result in escalating the O&M cost. The foundation’s stiffness degradation will result in a shift of the wind turbine system natural frequency, which may result in amplifying the vibrations generated at the hub. The anticipated shift of the wind turbine system natural frequency during the design-life time should be investigated through numerical simulations of the anticipated dynamic loading utilizing soil constitutive models that are capable of capturing the foundation stiffness degradation due to the accumulation of such small plastic strains. This study presents the validation of an element model that will be used to evaluate the performance of existing and/or proposed constitutive model.

Oct 1, 2022

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002

By James D. Hussin

The Florida limestone is a relatively soft rock which presents many challenges to engineers when designing deep foundations. One alternative is micropiles which have grown significantly from their early days as very small diameter, light capacity elements. Also known as minipiles, pin piles, needle piles or root piles, micropiles offer an attractive deep foundation alternative for sites with tight access, low headroom, and where difficult subsurface conditions or obstructions necessitate a small diameter, high capacity deep foundation. The ability to confirm the competence of the limestone bearing formation by drilling in a rock socket has made micropiles a growing deep foundation selection in Florida.

Jan 1, 2003

By Eric J. Pederson

The down hole hammer is widely used in specialty geotechnical construction. The common uses include tie-back anchor installation, micropile installation, and general soil/bedrock drilling operations. Veit used these techniques to develop a cost effective way of installing the foundation system for University of Minnesota Football Stadium. The soils present at the site of the stadium contained layers of concentrated cobbles and boulders. The geotechnical engineer recommended a driven pile system, and the base bid outlined in the project documents consisted of an H-Pile using a 14x73 pile section. Veit submitted an innovative alternate consisting of using a rotary percussion system to install a 12? O.D. pile. This paper will show that this pile type and installation method was the correct choice for the project. The design criteria for the compression, uplift, and lateral capacities and deflections were met, while eliminating pile damage. The method resulted in a significant cost savings to the University and maintained the project schedule.

Jan 1, 2008

By D. A. Ponniah

The installation of a pile is considered analogous to the expansion of a cylindrical cavity of a diameter equal to that of the pile. Using Vesic's theory of the expansion of cavities the effect of soil properties on pile installation loads, radial pore and total pressures are evaluated. The theoretical results are compared with load and pressure measurements made in field trials in a stiff clayey glacial till in the U.K.

Jan 1, 1987

By Christian Hoyme, Jochen Maurer, Hans Regler

Up to today, it has been very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. It is becoming more and more important to be able to analyze this process so as to notice bottlenecks and interruptions on the site early on. The high costs of each shift in special foundation industry mean that making the wrong decision and/or interruptions can put the financial result at risk. Previously, keeping reliable data meant manual process documentation. This was done either by an additional staff member (incurring high additional costs for training, education, etc.) or by the equipment operators. The latter is critical, because they have to initiate every process step change, leaving no time to log data separately. Studies have shown that there are considerable deviations from the actual process steps. In this paper, a seamless, automated method will be introduced to analyze the construction process. This method recognizes each process step from the equipment data. The main purpose of the data recorded by the piling rig is the need of quality reports and now basis for the presented analysis. Here, a method was successfully transferred from theoretical computer science (compiler construction field) to find application for process recognition. Because the execution of works in special foundation construction can always be defined sequentially and therefore also practiced sequentially, recognition can occur step-by-step. Our method always recognizes the next step, so it does not have to monitor as much data at the same time. Individual trigger points are easier to define. Unlike solutions that are based on a global approach and allocate suitable process steps to data patterns, thereby also creating gaps, the presented method is always seamless. Furthermore, this method can be applied regardless of time or location provided that the necessary machine data is available, which is normally the case with production data logging. This means that construction sites even from the past can also be analyzed and the results used for comparisons. The first results from the analysis of a complete continuous flight augering (CFA piles) installation process of a construction site will be presented.

Sep 8, 2021

By Joe Harris

Large structures, such as a multistory office building or a large storage tank, are constructed the most economical way possible, which may involve a shallow foundation system placed on native soil or compacted fill material. Over the life of the structure, the foundation system may not perform as originally anticipated, leading to differential settlement. Minor differ- ential settlement is expected; however, settlement that exceeds allotted tolerance can render the structure inoperable. Compaction grouting is a well-known and accepted ground improvement technique that can be used to not only stabilize but relevel multistory buildings and large dia- meter storage tanks. Two projects, each with differing types of structures, were successfully remediated utilizing com- paction grouting as the primary method to remedy settlement.

Sep 1, 2023

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No. 1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No. 2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No. 2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

Jan 1, 2013

By Carl Ealy

Static and STATNAMIC (STN) rapid load test (RLT) was performed on 3-drilled shafts. The purpose of the RLT part of the study was to obtain data in support of FHWA research on innovative load testing methods. The research site is located at the National Experimentation Research Site (NGES) in Amherst Massachusetts and is underlain by Connecticut valley varved clay. Two of the tested shafts were constructed without planned defects and the third with manufactured defects to evaluate current non-destructive integrity testing (NDE) methods. Quick Load Test (QLT) and Constant Rate of Penetration (CRP) static axial load tests were performed on two shafts to plunging failure. Good agreement between static and RLT derived static failure loads was attained for a 5% failure criterion (load at a movement equal to 5% of shaft diameter).

Jan 1, 2002