Search Documents

By I. R. Muirhead, S. Frimpong

"The mechanization of mining operations in underground coal mines has led to faster cutting rates of coalfaces with increased levels of emission of gaseous and particulate contaminants in the workings. Consequently, the fresh air streams from the main ventilation systems reaching distant workings are often insufficient, ineffective or inadequate and have to be supplemented by auxiliary ventilation systems to create and maintain the required working environments underground. The efficiencies of auxiliary ventilation systems are largely affected by drivers of the system such as the type and capacity of the fan; the type, length, diameter and condition of the ventilation ducting and the distance from the discharge end of the intake ducting to the face. Traditionally, single point measurements of methane gas concentrations using either flame safety lamps or hand-held measuring instruments have been used to assess how safe underground coal workings were. Unfortunately, such occasional measurements of methane gas concentrations do not give an accurate picture of the real gas concentration in the working as they are often taken from the easily accessible locations in working. Continuous monitoring of the methane gas concentration in development headings enables a better assessment of the environmental conditions prevailing there. All variations in the methane concentrations are more easily captured on a continuous monitoring basis than by instantaneous single point measurements. The approach adopted in this work was to continuously monitor the concentration of methane very close to the face and about 60 m outbye in development headings, observe the types of auxiliary ventilation equipment and their sizes being used in the working as well as noting the lengths from the discharge ends of the forcing and exhaust ductings to the face.In this paper, empirical methods are used to calculate the mean efficiencies of the auxiliary ventilation systems in selected development headings in coal mines in North America. This enables the assessment of the effectiveness of the auxiliary ventilation systems and the identification of the system drivers in them. The results show that the efficiencies of the forcing systems ranged from 17.02% to 96.81% while the efficiencies of the overall systems varied from 6.04% to 54.16%. The distance from the discharge end of the intake ducting to the face appeared to be the strongest driver in the performance of the auxiliary ventilation systems studied. It was also noted that when the discharge end of the intake ducting to the face does not exceed 7 m, there were faster purging rates of methane at the face and the efficiencies of the overall auxiliary ventilation system were greater than 50%. These findings are very important in underground coal mining in North America as they will assist to avert calamities, such as the Westray coal mine disaster in 1992 which resulted from the explosion of methane gas, by identifying which components of the ventilation system need special attention to create safe working conditions underground."

Jan 1, 2003

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By Tom Cooney

A small number of mining contractors worldwide have evolved their businesses to be able to provide a ?total service solution? to their clients. Thiess, an Australian-based international mining service provider, works with numerous clients to tailor delivery methods and commercial arrangements to suit individual projects. The benefits of Thiess? extensive experience is brought to each client and project, whilst business improvement within projects, to the mutual benefit of both the client and Thiess, is a key part of all long term contract relationships. Historically, optimal business outcomes were closely related to the achievement of production and cost performance measures. Whilst these remain fundamental to successful mining businesses, other elements of sustainability are assuming increasing importance. As a large energy user, greenhouse and energy management is becoming an important part of Thiess? business. Thiess is a signatory to Australian government initiatives such as Greenhouse Challenge Plus, and is integrating energy management into its operations and business improvement programs, in many cases to the benefit also of the client. This paper will highlight the benefits that an organisation such as Thiess can bring to a mine owner. Thiess? approach to business improvement and cost reduction, sustainability and energy management, as well as the relationship between these will also be considered. Increasingly, overall mining performance is dependent on the alignment of formally disparate elements.

May 1, 2007

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By R. E. Gilmore

PREAMBLE THIS PAPER comprises material presented in two separate 'Papers at the British Commonwealth Scientific Specialist Conference on Fuel Research held in London, England, in July, 1950. These papers are now available for publication in Canada, since only essential parts of the conference discussions, in addition to the resolutions resulting therefrom, will be published in the official Proceedings of the Conference. Inasmuch as the information presented concerns Canadian organizations and training facilities for fuel research, it should be of general interest to Canadian scientists, and especially to the Coal Division of the Canadian Institute of Mining and Metallurgy. Part I, the alternate title of which is Facilities in Canada for Fuel Research and for Exchange of Information and Staff, does not include research on peat, oil shale, petroleum oils in general, and natural gas, and omits studies of the geology, constitution, and production of coal. Special reference is, however, made to research on the heavy crude oils and bitumen of the Western Prairie Provinces, and particularly to their production and treatment to produce crudes for oil refinery processing.

Jan 1, 1951

By W. Hrynewich

"The Central Canada Potash facility, a division of Noranda Metal Industries Limited, is located 3 kilometres south of the junction of Highways 16 and 2, about 75 kilometres south-east of Saskatoon, Saskatchewan. The site occupies 26~ hectares of land and includes well-equipped machine and electrical _shops, a 325,000-tonne muriate storage and reclaim warehouse, a stores warehouse, processing plant (mill), two mine shafts (one for production, the other for servicing and personnel transport), as well as a two track product loading complex. Access to the site is by road and railway (CN and CP Rail). Suppliers of operating and maintenance use both means of transportation, whereas muriate shipments are entirely by railway.Currently five continuous mining machines - one a Goodman 526 borer and four Marietta 911-A units produce some 10,500 tonnes of ore per operating day. A smaller Voest-Alpine Af.1-100 boom type miner is used for floor cutting which was previously done by a production unit. In order to maintain safe, competent ground conditions only 35 percent of the total ore is extracted. At this rate mine reserves are deemed adequate for about 100 years. The plant has operated since August 1969 and has a current practical annual capacity of 1,270,000 tonnes of muriate. As of June 30, 1981, some 11.9 million tonnes of muriate had been produced from 31.4 million tonnes of ore. Of the total muriate, 6.1 million tonnes was granular, 4.8 million was coarse, and 1.0 million was standard. No standard product has been made since August 1978."

Jan 1, 1982

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end-use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here, we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilization to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilized to produce more effective dispersant systems which allow the preparation of added value, higher solids and finer particle size calcium carbonate slurry products. IntroductionConcentrated aqueous dispersions of fine particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently, more than 10 Mt of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e., its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximize the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimize drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003

By Alan E. Cameron

WE assemble again today in this comfortable, hospitable Inn to begin this, the 58th, Meeting of our Society. It is just a year ago when last we met but that year was, probably, the most portentious year in the whole history of mankind. In that year, the German 'Atlantic Wall' was broached, the Rhine was crossed, and Germany, as a Nation, has ceased to be. The agony of Europe is over; convalescence may be, probably will be, slow. But blood no longer flows in Europe. Time will heal the sores, cover the scars, regenerate the industries, rebuild the cities, and re-establish the people. True, the war of all wars is not yet over. True, a bloody conflict remains . But, the power of the United Nations now converges on one target. The rain of blood will be heavy. We can hope the storm will be short. The sun is on the horizon. The light of peace 1s in the sky. What of that Peace? Are we ready for it? Have we a 'sure foundation ' for our future world? Are the footings under that foundation broad and substantial? Can we look forward with confidence to a lasting peace and a fruitful life? The United Nations, even as this is being written, are in conference in San Francisco, placing the footings, rearing the foundations for a world edifice. There are bickerings; there are jealousies. The world is tired, and a tired family always squabbles. We can, we must, believe that the decisions they make, the edifices they rear, will be better than anything we each could effect separately. It will be a compromise, probably; it will carry things that will hurt us, just as it will carry things that will hurt others. We can, we must, believe that the good of the whole is a greater good than the good of the part. Each Nation within the United Nations must sacrifice something, each part of each Nation must sacrifice something, each individual within each part of each nation must contribute something, if the whole is to be wholesome. Sacrifice and contribution must be the order of the day if the New World we are about to build is to be worth while. What of Nova Scotia? The world has travelled far in the last year; how far has Nova Scotia gone? Canada has preparations for the Peace under way; what has Nova Scotia done? Is Nova Scotia preparing counter measures for the sacrifices it must make? Is each of us ready to contribute his share?

Jan 1, 1945

By André van Wageningen

Since the beginning of this century Boliden Mineral and Atlas Copco have worked together in stages on improving the accuracy and quality of drilling. Navigation of the drill rigs with IREDES has been in use in the Boliden mines for several years. Recently the capability of the system has extended with map navigation to more accurately follow the ore in cut&fill mines. The system allows for changes on the individual round level to follow the ore without changing the whole design for the heading. Those changes are done in a CAD-system and remove the need for face markings and will allow for even better accuracy in both height and wall position. All the information between the CAD-system and the drill rigs is exchanged using the IREDES standard. This paper describes the workflow and the use of the IREDES standard.

Oct 1, 2009

By Marcel Vallee, Fernand Dubuc

"The St-Honoré carbonatite complex, located 8 miles north of Chicoutimi, Quebec, was discovered in September 1967 as abnormal radioactivity was detected in the course of SOQUEM's aerial surveys. The complex, covered by a shallow layer of Trenton limestone, has been explored by aeromagnetic, ground gravimetric and magnetic surveys, and 12,013 feet of diamond drilling. Its age, from potassium-argon dating, is 650 million years. The carbonatite is approximately kidney-shaped and has a surface area of 6 square miles, 20 per cent of which is explored. It shows a central core of coarse-grained massive dolomitic carbonatite and an outer ring of foliated dolomitic carbonatite.The exploration work to date has resulted in the discovery, in the foliated carbonatite, of an incompletely drilled niobium (columbium) zone of pyrochlore-bearing carbonatite, at least 1,000 by 800 feet in size. This zone contains 5,000 tons per vertical foot grading 0.86 per cent Nb205 or at least 15,000 tons per vertical foot grading 0.66 per cent Nb205 or 45,000 tons grading 0.48 per cent Nb20s. The pyrochlore contains an average of 64 per cent Nb,Os. The central core contains a zone of rare-earth-bearing carbonatite (as monazite), grading up to 4.5 per cent rare-earth oxide, 3,500 ppm zinc and 290 ppm molybdenum. Stocks of nepheline syenite and magnetite diorite accompany the carbonatite. The total analysis and trace-element contents of typical rocks are presented."

Jan 1, 1970

By D. A. Karvonen

In 1970, the Government of Saskatchewan instituted a program aimed at resolving the dilemma of excess productive capacity over the market demand which existed for potash produced in Saskatchewan. The two primary elements of the program were prorationing of potash production to market demand and a minimum selling price. The paper reviews the factors, both local and international in nature that led to the introduction of the program. The licensing mechanics and the operation of the program, along with the changes that have been introduced in two and one-half years of operation, are discussed. Attention is given to the results of the controls as they affect the industry and the province. Also discussed is the outlook for Saskatchewan potash in world markets.

Jan 1, 1973

By Arthur D. FitzGerald

EDC established an Environmental Review Framework in 1999. Throughout the early fall of 2001, the Corporation held public consultations across Canada to strengthen that framework, leading to a public release on November 15, 2001 of a report summarising the results of these consultations. Following this, the Corporation implemented strengthened environmental review requirements in the form of its Environmental Review Directive, in compliance with legislated amendments to Canada?s Export Development Act that went into effect on December 21, 2001. Over the past few years, there has been a global trend towards an increase in the social and environmental requirements of multilateral/bilateral financial institutions and export credit agencies. More recently, this activity has focussed on capturing institutions that have not yet adopted similar requirements and, more specifically, on developing a convergence of the requirements from institution to institution. This paper describes EDC?s new ERD and some of the initiatives that have taken place or are in process that are moving international financial institutions toward converging their environmental and social requirements for projects in the private sector.

May 1, 2002

By Christoph Mueller

Broad band mine communication today is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and TCP/IP on the other side provides an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of cheap development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefor, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. To optimize the use of bandwidth on mining networks using load limited, ?bandwidth wasting? local Ethernet segments, long distance broadband traffic should be carried out using more efficient, deterministic communication backbones providing a guaranteed quality of service for each of the physically separated networks. Open networking and broadband systems however may lead to the anticipation that any demands on bulk data or multimedia traffic can be fulfilled in the future. This definitely will not be the case as the bandwidth demands of applications will be growing as least as fast as the bandwidth provided by communication systems. Looking on those problems from an overall system integration perspective, machines and equipment in the future have to be equipped with intelligent computing devices capable of an intelligent local data preprocessing. Such ?Embedded Machine Information Servers? running commercial computing power in the future will be the intelligent bridge between open networking and a secured, high safety local automation system. These ?Embedded Machine Information Servers? then also can make advantage of intelligent video and audio data preprocessing to store and transmit multimedia information ?on demand? or when the application requires it. Summarizing the potential for the future Ethernet based networking together with powerful communication backbones and intelligent local data preprocessing on the machines in the future will lead the way to integrative, reliable and cost efficient mine automation solutions.

May 1, 2002

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

By C. R. Stelck

"AbstractThe Cardium formation of northeastern British •Columbia •contains an erosional unconformity that becomes progressively more severe northward until, •at Liard river, the stratigraphic hiatus eliminates the underlying Lower •Cardium sandstone, the Kaskapau formation, and the upper Dunvegan sandstones. The area of unconformity roughly coincides with the distribution of the continental facies of the earlier Dunvegan formation. Along Wapiti river, the zone fossil Scaphites ventricosus Meek and Hayden is found in the Bad-heart member of the overlying Wapiabi shale; Scaphites :preventricosus. Cobban marks the base of the Wapiabi shale; Scaphites cf. corvensis •Cobban is found in the middle shale member of the •Cardium formation. The log of the Red-Willow No. 1 well shows close similarity to the outcrop sections south of Wapiti river. The Cardium formation is mainly late Turonian in age. Two other pre-Cardium Turonian sands of north-eastern British Columbia are named the Wartenbe and Tuskoola sands.IntroductionTHE Upper Cretaceous Cardium (Bighorn) sandstone formation of the Foothills of northeastern British Columbia carries within its formational limits an erosional unconformity. The unconformity decreases to the southeast, becoming in immediate shoreline regions, now under the plains, a minor diastem. Such diastems, or stratigraphic intervals of non-deposition, occurring in the shallow unda-zone are paralleled in the deeper portions of the unda-zone by the phenomena of sub-aqueous winnowing. '.This winnowing and re-working •at critical depths creates sand areas with porosity."

Jan 1, 1955

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By D. C. Rance

"The Quintette Coal Limited property is located in the north east coal area of British Columbia. A basic agreement with the Japanese steel industry was ex ecuted on January 27, 1981 for the sale of 69.5 million tonnes of Quintette metallurgical coal over a 14.5-year period. This contract period can be extended by Jive years by mutual agree ment. Sale agreements have also been signed for the sale of 19.4 million tonnes of oxidized coal over a 15-year period. Work started on site development in the late summer of 1981, and at present, two of the four eventual pits-the McConkey and Frame-are under development. The pits are currently in a pres/ripping phase. These pits are notable for the stripping volumes that have to be removed from relatively small pit areas. in order to provide for the required detailed rapid short-range planning of these pits, engineering will be computerized, as will the truck dispatch system. The mining area lies 21.1 km from the plant site by road and the transport of raw coal LO the plant is by means of a highspeed conveyor system which has a total length of 13.4 km with a vertical drop of 740 m. The surface plant facility was designed on a modularized basis to facilitate maintenance, and is designed to enable the use ofgravity flow ofraw coal and heavy media in the plant to minimize the use of pumps. The construction of the plant and mine site facilities is on-going, and the first coal production is scheduled for early December 1983. Introduction Quintette Coal Limited is a Canadian company incorporated in the province of British Columbia in 1971. Denison Mines Limited is the manager of Quintette's activities. Equity in Quintette Coal Limited is held by several shareholders, with interests as follows: Denison Mines 'Limited, 500Jo; Charbonnages de France International S.A., 120Jo; and Japanese interest, 38%. The project will develop almost 120 million tonnes of coal for marketing during its first 20 years of production. All of the planned production tonnage has been committed to Japanese markets. Most of the coal will be metallurgical grade, and the remainder will be a high-quality thermal coal. The Mcconkey and Frame pits, which will initially provide the mine's production, will commence production in early December 1983 and will, in 1985, reach the full annual production of 5 million tonnes clean metallurgical coal and 1,380,000 tonnes of clean thermal coal."

Jan 1, 1985

By André Chagnon, Yvon Héroux

"Résumé - Cette étude porte sur l'altération de la matière organique et des argiles dans les boues carbonatés dévoniennes du faciès ""F"" de la Formation de Pine Point et ses équivalents stratigraphiques la Formation d'Evie et l'unité bitumineuse de la base de la Formation de Horn River. La matière organique se compose principalement de bitume solide et de quelques fragments de fossiles (organo­ clastes). La majorité des échantillons ne renferment que de l'illite et des interstratifiées illite/smectite.Si on compare les températures d'homogénéïsation (Th = l00°C) des inclusions fluides de la sphalérite et des dolomites associées à la minéralisation aux températures estimées à partir de la réflec­ tance de la collinite (84°C à ll7°C), l'on ne peut pas conclure à la présence d'une anomalie ther­ mique dans le district minier de Pine Point. De plus, la réflectance des organoclastes n'est pas plus élevée dans le district minier de Pine Point que dans les localités plus éloignées des gîtes. L'analyse des minéraux argileux conduit à la même conclusion : aucune anomalie thermique n'est décelable dans les unités échantillonnées à l'intérieur du district minier de Pine Point quelque soit l'indicateur utilisé.La kaolinite et la matière organique altérée, affichant des valeurs anomales de sa réflectance, se trouve essentiellement en présence de soufre et de sulfures. Cela suggère une origine authigène de la kaolinite et une altération de la matière organique reliées au phénomènes de minéralisation.Abstract- The alteration of organic matter and clays is studied in the Devonian Pine Point Formation carbonate muds, ""F"" facies, and its lateral equivalents the Evie Formation and the biturninous unit at the base of the Horn River Formation. The organic matter is mainly composed of solid bitumen with few fossil fragments (organoclasts). Most samples contain only illite and mixed layer illite/smectite.If we compare the Th(l00°C) from fluid inclusions of sphalerite and dolomites associated with mineralization to the temperatures calculated from the reflectanœ (Ro) of the collinite (84°C to 117°C), we cannot detect a thermal anomaly in the Pine Point mining district. This result is based on the reflectance values of organoclasts from the mining district that are not higher than those reflectance values measured on organic matter (OM) away from the ore deposit. A similar conclusion is reached from the clay study: none of the parameters used allow us to identify a thermal anomaly in the samples from the mining district.The kaolinite and the altered OM showing anomalous Ro values mainly occur with sulfides and sulfur. This association suggests an authigenic origin for the kaolinite and an alteration of the OM due to the mineralization events."

Jan 1, 1994

By I. Dymov, W. Phillips

A process has been evaluated, on a continuous pilot plant scale, to treat refractory gold arsenopyrite/pyrite concentrates. The process consisted of biological leaching to partially oxidise sulphides, followed by pressure leaching for complete sulphide oxidation and arsenic precipitation, followed by liquor neutralisation and cyanidation of the autoclave residue for gold recovery. This paper provides a brief description of the treatment flowsheet and discusses some of the main parameters and results of the process. During integrated pilot plant campaigns, it was confirmed that acceptable sulphide oxidation and gold extraction of 96-98% could be achieved by a two-stage oxidation with BIOX® (4 days total retention time) followed by PDX (40 minutes retention time at 220°C). Only partial arsenic precipitation was achieved in the autoclave, followed by complete precipitation by neutralization under atmospheric conditions. The overall process could be significantly simplified, and capital and operating costs reduced, with a flowsheet modification allowing all of the BIOX® liquor to bypass the autoclave directly to the neutralization circuit.

Jan 1, 2004