Search Documents

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world's largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems.

Jan 12, 1957

P. W. BRIDGMAN.-Owing to a misunderstanding, I did not see Dr. McAdam's and Dr. MacGregor's remarks on my paper on Flow and Fracture (Metals Technology, December 1944, Pp. 32-38), until after their publication. Both Dr. McAdam and Dr. MacGregor speak of my analysis for the stress distribution at the neck of a tension specimen as containing several assumptions; in particular, that the strain is uniform across the section of the neck, that there is no hoop tension at the periphery, and that the plasticity conditions of von Mises hold. As far as the mathematics goes, the situation is no different in this problem of plastic flow than in a conventional problem of elasticity. That solution is unique which satisfies the boundary conditions on the stresses, the stress equations of equilibrium, and in addition the constitutive equations connecting stress and strain in the elastic case, or a corresponding set of equations, of which the von Mises relations are a special form, in the plastic case. In the particular case of the necked tension specimen I have found that there is a solution satisfying the boundary conditions, the stress equations of equilibrium, and the von Mises plasticity conditions in which the strain is uniform across the section, and there is no hoop tension at the periphery. This is therefore the solution, and the uniformity of strain and vanishing of hoop tension at the periphery are to be described as discoveries, over which the operator has no control, rather than as assumptions. The only part of the solution that can properly be described as an assumption is the von Mises plasticity condition. With regard to this it is to be noted that the condition is needed only in a much weakened form, for the analysis uses the condition only at the neck, where the strain is approximately constant. Thus, in the extreme case referred to in a footnote of my paper (p. 37, Met. Tech. Dec. 1944) the actually measured strain across the section varies from 2.4 to 2.6. Obviously it is a much weaker assumption to postulate that the von Mises condition holds in the strain range 2.4 to 2.6 than to assume it to hold for the entire range of strain from o up to 2.6, which would be necessary if the solution applied to the entire tension specimen rather than to the immediate region of the neck only. Furthermore, it is to be commented that under the special conditions of this problem the von Mises condition becomes identical with the maximum shearing-stress criterion of plastic flow; this amounts also to a weakening of the restrictions imposed by the von Mises condition. Dr. MacGregor refers to actual experiments of his own in which the strain was found not to be uniform across the neck. It is to be emphasized, however, that these were experiments on bars of rectangular section, and that the nonuniformity established was a nonuniformity around the perimeter, not a nonuniformity from the surface toward the axis. My method of solution applies only to a circular cross section. It can be said that the solution that satisfies the boundary conditions, etc., would definitely not be expected to demand a uniform strain for noncircular sections. In discussing my results, Dr. McAdam uses a definition of "flow stress" different from mine, so that the immediate applica-

Jan 1, 1945

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By Donald A. Brobst

The minerals barite (BaSO4-barium sulfate) and witherite (BaCO3-barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1980 consumed at least 90% of the world's production of 8.8 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The remaining 10% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity filling, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favorable for the discovery of new deposits of commercial value. Witherite is much less common and abundant than barite, although it is more desirable in many ways as a raw material for the production of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir conditions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemically, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite homogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber industry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and linoleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other substances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weigh down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1983

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

Jan 1, 1933

By G. Howell Clevenger, Bhupendranath Ray

Formerly great divergence of opinion existed in regard to the influence of copper in steel, as affecting its various physical properties. More recently the investigations of Stead,l Breuil,2 Wigham,3 Burgess and Aston: Ball and Wingham,5 Miiller; Dillner,7 and others have shown fairly good agreement in the major points. Copper steel has been shown by these investigators to possess special properties which make it valuable for certain uses. The general range of composition of the useful alloys of copper and iron, and of copper, iron, and carbon, has been quite definitely established, for the former by Burgess and Aston,8 and for the latter by Breuil9 and Stead.10 Stead11 has removed one difficulty in reconciling certain of the earlier data by calling particular attention to the influence 'of carbon in copper steels. Another point which caused confusion in the earlier investigations, particularly in regard to " red-shortness," was the presence of sulphur. Failure to note the presence of sulphur often led to attributing " red-shortness" to the presence of small amounts of copper. Turner12 has called attention to the fact that where copper exists in an iron ore it often occurs as the sulphide, so that the presence of copper in steel made from such ores might also, necessarily, mean the presence of sulphur. It is evident that the effect in this case might be quite different than where pure copper was added.

Jan 1, 1914

By T. E. Watkins, M. D. Nelson

A method of determining the lime content of drilling muds proposed by Battle and Chaney* has been examined both in the Field Research Laboratories of Magnolia Petroleum Co. and in field drilling operations. This proposed analytical method is condensed as follows: Titrate one ml of mud and one ml of mud filtrate, each with 0.02 N H2SO4, to the end point with phenolphthalein. The volume of acid in ml required for the mud titration is recorded as Pm and that of the mud filtrate titration as Pf Calculation of the lb lime/bbl mud is accomplished by use of the formula, lb lime/bbl mud = 0.6 (Pm - 1.3Pf) - 0.6 The analytical procedure outlined by Battle and Chaney was found to be quite satisfactory when reasonable precautions are used in mud sampling technique. Calculation of lime concentration by the method proposed in the above publication, however, has given values that varied as much as 100 per cent from the known lime content, for muds of either high or low solids concentration. By use of a formula, lb lime/bbl mud = 0.26 (Pm-F1.Pf), based on chemical equivalents of acid required for titration, both laboratory and field data have been satisfactorily correlated with the known amounts of lime present in the muds. In this formula a correction, F1, or volume fraction of liquid in the mud, is made for the solid content of the mud. Pm and Pf * Paper on "Lime Base Muds," presented by J. L. Battle (Humble Oil and Refining Co., Houston, Tex., and P. E. Chaney (Sun Oil Co., Beaumont Tex.), at the 1949 Spring Meeting of the Southwestern District API Division of Production, Dallas, Tex. The analytical procedure has also had wide distribution in a trade journal, Kembreak, published by the Accuracy Rig and Tool Co., Houston, Tex, †Derivation of equation lb/bbl — grams/350 ml 1 ml 0,02 N acid = 0.000741 grams of lime 1 ml 0.02 N acid/ml lime suspension = 0.26 lb of lime bbl lb of lime/bbl = 0.26 (Pm -F1, Pf ) have the same significance as in the Battle and Chaney equation. Table I shows typical data employing both formulas in calculating the lime content of various lime muds. This suggested procedure ignores lime which is in solution in the mud. The solubility of lime in water, normally about 0.5 lb per bbl, is greatly decreased by the addition of caustic soda, and, in a lime mud, it is probable that the concentration of dissolved lime is of the order of 0.1 lb per bbl. Such an amount of lime can be ignored, since it is within the range of accuracy of the method.

Jan 1, 1950

By R. V. Norris

The anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, iii the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of' the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jan 1, 1912

By Victor L. Stevens

The Oso tunnel is one of three tunnels located on the San Juan-Chama Project in south-central Colorado. The purpose of the tunnel is to carry water from the upper San Juan watershed through the Continental Divide into the Rio Grande watershed. The Oso tunnel contract was awarded by the U.S. Bureau of Reclamation to a joint venture of Boyles Brothers Drilling Co., Gibbons & Reed Co., and Cimco in February 1966. The Oso tunnel is 26,660 ft long and has a rock section of 10 ft, 2 in. with a lined diameter of 8 ft circular. The main portion of the rock formation was in the Lewis shale. This formation is quite consistent in hardness and texture with exception of localized limestone concretions and sandy siltstone inclusions. The job was bid on the basis of using a James S. Robbins mole of the P221 series. The decision for using a mole was predicated on the geology and the experience of the same joint venture on the adjoining Azotea tunnel where a mole was successfully used. The Robbins P221 series mole is capable of cutting from 9 ft, 11 in. to a 10 ft, 7 in. diam without any major change. It is 40 ft long and weighs 60 tons. The cutting head has 22 disk-type cutters and one center pilot (standard 9 7/8 -in.) tricone bit. The head is powered by four 75 hp electric motors. Gripper pads at about the midway point on each side of the machine are pushed into the tunnel ribs and thrust-cylinders in front of each gripper apply pressure to the face as the head rotates. The regripping cycle is 3 ft and then the grippers are retracted and advanced. Each cutter on the perimeter of the head is followed by a bucket which scoops up the cut material, almost in the same manner as a water wheel, and dumps it into a conveyor situated along the top of the mole. The muck from the mole conveyor is dumped into a gantry-type conveyor. The gantry conveyor is 350 ft long and is pulled

Jan 1, 1970

By M. S. Seltzer

In a previous paper1 it was shown that activation energies for steady-state creep in lead sulfide single crystals varied with the concentration of electronic defects. For n-type lead-excess crystals, values for the creep activation energy, Qc, decreased from 2.9 to 2.2 ev as the carrier concentration increased from 1017 to 1017 electrons per cu cm, while Q, increased from 1.6 to 2.3 ev for p-type sulfur-excess crystals as the concentration of holes increased from 6 X 1017 to 1018 per cu cm. It was also shown in Ref. 1 that the Q, values could best be correlated with the sum of the self-diffusion activation energies in PbS, i.e., for a given concentration of electrons or holes Q, = QPb + Qs, where Qpb and QS are the activation energies for diffusion of pb210 and s35 in PbS. This result suggests that creep rates are controlled by at least two atomic defects, one for lead migration and one controlling sulfur transport. It would be most desirable to interpret these creep energies in terms of an atomic defect disorder model for lead sulfide. Studies of creep rates as a function of sulfur pressure2 indicate that the defects controlling creep rates are singly ionized lead and sulfur vacancies, VPb and Vs. This hypothesis can be more firmly established by determination of Q, under conditions of constant atomic defect concentration rather than constant electronic defect concentration as has been previously done. Therefore, several measurements have been made of Q, on crystals whose con- centration of lead vacancies or sulfur vacancies has been fixed by equilibration under appropriate sulfur pressure and temperature. It was indicated in Ref. 2 that high-temperature isotherms are available which show how the concentrations of various atomic point defects in PbS vary with composition over the entire homogeneity range for the compound. Two such isotherms are shown in Fig. 1 for 900" and 1000°K. Utilizing these isotherms the concentration of a given defect, say Vbb, may be held constant over a particular temperature range by adjusting the sulfur pressure as the temperature is changed. Thus the concentration of one defect suspected of controlling creep rates may be held constant while other defect concentrations vary. The apparent activation energy for formation of these defects can be obtained from the isotherms giving their concentration as a function of sulfur pressure. Activation energies for creep obtained under conditions of constant defect concentration can then be compared with defect formation energies and certain possible atomic defects can be eliminated as creep-controlling species. We have performed creep experiments as a function of temperature at a stress of 244 g per sq mm under conditions which fixed the lead vacancy concentration, V', at 1016, 3.2 x 1016, and 3.2 x 1017 cm-3, and one were the sulfur vacancy concentration, Vs, was held at lo17 cm-3. The results are presented in Fig. 2 as creep rate, k, vs reciprocal of absolute temperature, 1/T. Specimens 34, 35, and 36 were deformed under constant lead vacancy concentration while specimen

Jan 1, 1969

By G. L. Schroeder

Investigations were conducted at two underground locations, foreman's room and 5702 area, of the Kermac Nuclear Fuels Corp. uranium mining installation, Ambrosia Lake, New Mexico. The rock environment is stratified sandstone. Pressures were varied from minus 0.4 an Hg to plus 3.8 cm Hg with respect to barometric pressure, and were maintained for periods ranging from several hours to 21 days. One cm Hg overpressure (-1.5% of normal barometric pressure) produced a 20-fold decrease in Rn flux into the foreman's room as compared to the Rn flux observed during dilution ventilation. The 5702 area experienced a 5-fold decrease in Rn flux for a similar overpressure. During 21 days of continuous 1 cm Hg overpressure in the 5702 area this reduced Rn flux was maintained. The smaller reduction in flux for the 5702 area results in part from the proximity of the foreman's room to a non-pressured area and the presence of an impermeable shale lens overlying the ceiling of the 5702 area. A 0.4 cm Hg underpressure of the 5702 area increased the Rn flux into the area by 3-fold over the non-pressured value. A barometric pressure influence on Rn flux into the mine and on air Rn concentrations in non-pressurd areas of the mine was measured. A falling barometric pressure causes an increase in the flux of interstitial gas into the mine; a rising barometric pressure decreases this flux. These effects are not seen in overpressured mine areas. Radon concentrations in rock interstices show, during overpressure, decreases of all locations monitored except in the immediate vicinity of the shale lens above the 5702 area ceiling. These reductions are the result of air flowing from the mine into the rock interstices under the influence of the pressure gradient induced by the overpressure. The relative humidity of the 5702 area was reduced after 2 days of 1 cm Hg overpressure from a pre-overpressure value of 96% to 81%. The control of harmful or noisesome gases which emanate into underground mining areas from surrounding rocks is often a costly necessity. In uranium (U) mines this problem is presented by the high interstitial concentrations of radon-222 (Rn), a radioactive noble gas of 3.82-day half-period, formed in the decay scheme of U238, and the relative ease with which this noble gas diffuses from its parent rock into the interstices of the rock and then to a working area. Long-term exposure to moderate concentrations of Rn (3000 µµc per 1) and its short-lived alpha-ray emitting daughter products, RaA (Po218) and RaC (po214), has been found to result in an increased incidence of bronchial carcinomaa2 The acceptable limit of Rn daughter products in a mine atmosphere is presently set at a concentration of short-lived radon daughters which would be in equilibrium with 100 ppc of Rn per 1 of air. Ventilation of mines is conventionally accomplished by continuously diluting the mine air with fresh air brought in by fan or natural convection from above ground surface. The diluted air is allowed to vent freely to the atmosphere. This process does nothing to retard the rate at which gases (including Rn) diffuse into the mine from surrounding rock. It merely reduces the concentrations of these gases within the mine. It is suggested that in a sufficiently permeable rock environment a slight pressurization of the mine air may induce air flow from the mine into the interstices of rock surrounding the mine. The convective flow of comparatively fresh air will reduce the concentration and the concentration gradient of undesirable gases in the rock interstices adjacent to the mine. Radon will diffuse counter-current to this convective flow at a rate proportional to its concentration gradient. In time, a steady state of convection and counter diffusion will be established. The Rn flux into the mine will never be reduced to zero, and will only asymptotically approach zero as the overpressure (and hence the convective velocity of purging air) approaches infinity. During 1963 and 1964, an investigation into the effect which such applied pressures have upon the Rn characteristics of a mine atmosphere was conducted at the Kermac Nuclear Fuels Corp. uranium mines, Ambrosia Lake (near Grants), New Mexico.

Jan 1, 1967

By Raymond E. Birch, Oscar M. Wicken

THE mineral magnesite, formerly the source of nearly all magnesia, now shares this role with brucite, dolomite, and the world's natural and artificial brines. The mineral magnesite is the normal carbonate of magnesium, MgCO3, composed when pure of 47.6 pct MgO and 52.4 pct CO2. It is one of the calcite (CaCO3) group of rhombohedra1 car- bonates, which also includes dolomite, CaCO3.MgCO3, and siderite, FeCO3. Magnesite does not form an isomorphous series with calcite or dolomite; consequently, these lime-bearing carbonates commonly present in magnesite deposits are there only as mechanical mixtures. Magnesite and iron carbonates form a continuous isomorphous series and therefore are inseparable mechanically. The variety of magnesite known as breunnerite is an isomorphous mixture of iron and magnesium carbonates. Magnesite may be either crystalline or amorphous (cryptocrystalline). The former, which includes breunnerite, is often termed spathic magnesite. Crystalline magnesite varies from finely to coarsely crystal- line in texture and has a hardness of 3.5 to 4. The color is white, yellowish, blue-gray to drab, red, pink, black, or mottled. It is seldom found pure but usually contains variable amounts of iron, lime, silica, and sometimes manganese. The color cannot be used as an index of purity. The cryptocrystalline variety is perhaps the more common type but the crystalline variety usually occurs in larger deposits. The amorphous type is fine grained and compact, showing no cleavage. It is usually snow white but sometimes is light to pale orange yellow or buff, owing to impurities. The fracture is conchoidal to uneven and the hardness 3.5 to 5. Silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. The lime and iron contents are usually low. In general, amorphous magnesite is somewhat purer than the crystalline variety. The specific gravity of cryptocrystalline magnesite is 2.90 to 3.00. Pure crystalline magnesite has shown a specific gravity of 3.02 but iron

Jan 1, 1949

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have dealt with the methods of separating silver from copper. There now remains the portion which treats of solidified juices ; and whereas they might be considered as alien to things metallic, nevertheless, the reasons why they should not be separated from it I have explained in the second book. Solidified juices are either prepared from waters in which nature or art has infused them, or they are produced from the liquid juices themselves, or from stony minerals. Sagacious people, at first observing the waters of some lakes to be naturally full of juices which thickened on being dried up by the heat of the sun and thus became solidified juices, drew such waters into other places, or diverted them into low-lying places adjoining hills, so that the heat of the sun should likewise cause them to condense. Subsequently, because they observed that in this wise the solidified juices could be made only in summer, and then not in all countries, but only in hot and temperate regions in which it seldom rains in summer, they boiled them in vessels over a fire until they began to thicken. In this manner, at all times of the year, in all regions, even the coldest, solidified juices could be obtained from solutions of such juices, whether made by nature or by art. Afterward, when they saw juices drip from some roasted stones, they cooked these in pots in order to obtain solidified juices in this wise also. It is worth the trouble to learn the pro- portions and the methods by which these are made. I will therefore began with salt, which is made from water either salty by nature, or by the labour of man, or else from a solution of salt, or from lye, likewise salty. Water which is salty by nature, is condensed and converted into salt in salt-pits by the heat of the sun, or else by the heat of a fire in pans or pts or trenches. That which is made salty by art, is also condensed by fire and changed into salt. There should be as many salt-pits dug as the circumstance of the place permits, but there should not be more made than can be used, although we ought to make as much salt as we can sell. The depth of salt-pits should be moderate, and the bottom should be level, so that all the water is evaporated from the salt by the heat of the sun. The salt-pits should first be encrusted with salt, so that they may not suck up the water. The method of pouring or leading sea-water into salt-pits is very old, and is still in use in many places. The method is not less old, but less common, to pour well-water into salt-pits, as was done in Babylon, for which Pliny is the authority, and in Cappadocia, where they used not only well-water, but also spring-water. In all hot countries salt-water and lake-water are conducted, poured or carried into salt-pits, and, being dried by the heat of the sun, are converted into

Jan 1, 1950

By R. J. Wysor

Since the outbreak of the European war, few problems of raw-material supply have commanded more nation-wide attention than potash. It is well known that before the war the domestic production of potash was an insignificant percentage of the imports. The average annual importation of raw potash salts for several years prior to 1914 was slightly over 300,000 net tons, and of other potash manure salts about 700,000 tons. The sudden and almost total cessation of these imports created a unique and stringent situation. Methods of recovering potash from feldspar and other native mineral sources, and reclamation from hitherto waste products, have received a marked impetus. Soaring prices have been a keen incentive to research and industrial development. Although several brief articles concerning the possibilities of potash recovery have appeared in recent trade journals, it still may be a matter of some surprise to the average technical mind that potash might be reclaimed as a profitable byproduct in the manufacture of pig iron. At the present time it may be of special interest to present some data, largely of a technical nature, on this subject. A fairly thorough search of the literature reveals a number of articles concerning salts of the alkali metals in the blast furnace. Many of them deal with the theoretical rôle of alkali cyanides in the furnace. Several discuss the probable effect of the alkalies on the furnace brickwork. Two or three ambitious patents have been granted for reclaiming potash or other products from blast-furnace gas. However, we have heard nothing further as to the practical application of these patents. Little literature of importance has appeared during the last 10 years concerning alkalies in blast-furnace practice, and I have discovered no record whatsoever as to the actual sale or commercial disposal of flue dust for its potash content until this was inaugurated in our plant at Bethlehem. A bibliography of the most important articles discovered is appended. About 4 years ago, in the course of investigating blast-furnace stove efficiencies, I analyzed the fine, yellowish fume of which a considerable

Jan 1, 1917

By Arthur La Motte

I NDUSTRIAL explosives, as distinguished from military explosives, include high explosives and blasting powder. The high explosives which are best known are straight dynamite, gelatin dynamite, ammonia dynamite and permissibles. There are two kinds of blasting powder, saltpetre blasting powder and nitrate of soda blasting powder. Blasting powders are mechanical mixtures of nitrate of potash or nitrate of soda with sulfur and charcoal, highly compressed, granulated and glazed. They ignite from a spark and burn with relative slowness, the rate of burning and hence the rate of conversion into gases depending upon the size of the granulation and upon the degree of. confinement under which the powder is placed. High explosives, on the other hand, are chemical compounds which detonate; that is, when the explosive is subjected to a violent shock, provided in practice by a blasting cap or an electric blasting cap, the molecule of the essential ingredient, usually nitroglycerin, is disrupted and the energy and heat released cause any other explosive ingredients which may be present, such as ammoniuin nitrate or T.N.T., to decompose with a resultant evolution of gases at an extremely rapid rate varying from 6000 to 20,000 ft. per second.

Jan 1, 1924

By Michael Perch

The fact that coal is a complex organic material and heterogeneous in composition has made its study extremely difficult, particularly in regard to obtaining a fundamental concept of the processes involved in the formation of coke. It has been stated recently that coals are natural polymers and that in a complex reaction such as occurs during carbonization the differences between coals are quantitative and not qualitative. Such being the case, it would be expected, therefore, that a series of coals subjected to exactly the same conditions of coking would produce results that should be related quantitatively to the chemical analyses of the individual coals. In the past, however, this fact was not generally recognized and consequently many empirical test methods were devised for testing coals. The interpretation of the results obtained depended upon comparing a set of data with other data on coals of known characteristics. The testing procedure had to be con- ducted in precisely the same manner each time and not the least requirement in making the interpretation was experience. The test methods varied from those utilizing a gram of coal to the plant-scale tests in which one or more ovens were charged with the test coal. The aim had been principally to find some simple, inexpensive means by which the coke-making and other properties of coal could be predicted. It is not necessary to emphasize the importance of these endeavors, for anyone acquainted with the problems involved in the selection of coals for making coke is well aware of the time and expense involved in making a series of definitive tests.

Jan 1, 1949

By James M. Barker

Sulfur is a nonmetallic element of great physical and economic importance to the world. It is widely but sparingly distributed throughout the hydrosphere, lithosphere, and biosphere. Sulfur is the tenth most abundant element in the universe and eighth most abundant in the sun. In the earth's crust, which is mainly igneous, it ranks 14th, but is eighth or ninth in sediments (Kaplan, 1972; Stanton, 1972). It apparently is very abundant in the core of the earth, because it is a strong chalcophile, and it is fifth in abundance in stony and iron meteorites (Field, 1972) where it occurs as trolite (FeS). In ancient times sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Shelton (1979) summarized most of the common definitions of terms, grades, and specifications for the sulfur industry as follows (with minor additions): Sources of Sulfur: Combined sulfur-Sulfur that occurs in nature combined with other elements. Cupriferous pyrites-Pyrite containing relatively minor amounts of copper sulfide minerals. Hydrogen sulfide-A toxic gas (H2S) occurring in natural gas and petroleum. Involuntary sulfur-Sulfur produced primarily as a result of legislative or process mandates. Native sulfur-Sulfur that occurs in nature in the elemental (uncombined) form. Nonferrous metal sulfides-Copper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfurs-Complex organic sulfur compounds occurring in petroleum, coal, oil shale, and tar sands. Pyrites-Iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfurs-Sulfur in anhydrite and gypsum. Voluntary sulfur-Sulfur produced in response to market forces. Basic Sulfur Products Produced and Marketed: Acid sludge-Contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-Synonymous with crude sulfur. Bright sulfur-Crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-Solid crude sulfur crushed to -8 in. Byproduct sulfuric acid--Sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-Commercial nomenclature for elemental sulfur. Dark sulfur-Crude sulfur discolored by minor quantities of hydrocarbons ranging up to 0.3 % carbon content. Elemental sulfur-Processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-Elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-Elemental sulfur produced from native sulfur sources by the Frasch mining process. Hydrogen sulfide-Associated with natural gas or petroleum and produced at refineries and coke oven plants; used to make sulfuric acid or recovered sulfur. Liquid sulfur-Synonymous with molten sulfur. Liquid sulfur dioxide-Purified sulfur dioxide compressed to the liquid phase. Molten sulfur-Crude sulfur in the molten phase.

Jan 1, 1983

By T. B. Nolan, R. N. Hunt

In terms of present metal prices, analysis of extant records of the Eureka district indicate past production of the magnitude of $200,000,000 in recovered silver, lead, and gold. Production to date has been thoroughly oxidized ore from massive replacements, fissures, manta, and pipe-like bodies-in large part from the massive Eldorado (middle Cambrian) and Hamburg (middle to late Cambrian) dolomite horizons. In the productive area of about 6 square miles carbonate rocks comprise 80 per cent of the section, which includes early Cambrian to late Ordovician horizons. Four-fifths or more of the district's production came from a block of Eldorado dolomite in Ruby Hill that was moved in over younger horizons on strands of a regional thrust fault. The lower 500 to 600 feet of the block was much fractured and brecciated and became host to the ores. The Ruby Hill fault, a late normal fault, limits the Ruby Hill block of dolomite on the north for its entire length of nearly a mile and terminates the downward extent and exploitation of its ores. It introduced an hiatus of some 40 years in the district's development. Drilling of the past 20-odd years, followed by underground work, has now exposed the down-faulted extension of the Ruby Hill block of Eldorado dolomite and its contained ores, dropped 1800 feet in a dip shift to depths beneath the surface of 2000 to 3000 feet. The ores at depth are the sulfide counterpart of those mined in early years on the footwall side of the fault. The ores of the district may be attributed to the same source as the intrusive quartz diorite outcropping in a limited way south of Ruby Hill but found at depth elsewhere in drill holes. The long north-south axis of the district, its anticlinal structure, its major faults, and the distribution of the intrusives and, in their relation to the surface, the ores themselves, all suggest that erosion has not cut deep enough to expose the extent of intrusives and the ores consequent upon them.

Jan 1, 1968