Search Documents

By G. R. Speich

The distribution of carbon and the type of substructure in iron-carbon martensites containing 0.02 to 0.57pct C has been studied in the as-quenched condition and after tempering at 25" to 700°C by using electrical resistivity, internal friction, hardness, and light and electron microscope techniques. in marten-sites containing less than 0.2 pct C, almost 90 pct of the carbon segregates to dislocations and to lath boundaries during quenching; in martensites containing greater than 0.20 pct C, appreciable amounts of carbon enter normal interstitial positions located far from defects. Tempering martensites with carbon contents below 0.20 pct at temperatures below 150°C results in additional carbon segregation to dislocations and to lath boundaries but no carbide precipitation whereas -carbide precipitation occurs in martensites with carbon contents exceeding 0.2 pct. Above 150°C, a rod-shaped carbide (either Fe3C or Hagg) is precipitated in all cases. At 400°C, spheroidal Fe3C precipitates at lath boundaries and at former aus-tenite grain boundaries. At 400" to 600"C, recovery of the martensite defect structure occurs. At 600" to 700°C, recrystallization of the martensite and Ost-waW ripening of the Fe3C occur. The effects of the carbon segregation that occurs during quenching and the subsequent substructural changes that occur during tempering on martensite tetragonality, hardness, and precipitation behavior are discussed. A mathematical analysis of carbon segregation during quenching is presented. RECENT studies of the strength of low-carbon martensitel-4 emphasize the importance of carbon segregation to the martensite lath boundaries and to the dislocations contained between them during quenching. Unfortunately, very few studies of the tempering of low-carbon martensites have been conducted, so the exact nature of this segregation is poorly understood. In fact, most early tempering studies5,6 were restricted to carbon contents greater than 0.20 pct. Moreover, these studies did not determine the amount of carbon segregated to the martensite substructure during quenching so that the initial state of the martensite was not established. Aborn7 studied the precipitation of carbide in low-carbon martensite during quenching but did not establish whether carbon segregation occurs prior to carbide precipitation, nor did he study the subsequent tempering sequence in detail. In the present work we have used electrical resistance and internal friction measurements, supplemented by electron transmission microscopy to establish the carbon distribution in as-quenched specimens. Specimens thin enough to avoid carbide precipitation (but not carbon segregation) were employed. The redistribution of carbon on subsequent tempering below 250°C was followed by measurements of elec- trical resistance. Additional studies were made on specimens tempered at 250" to 700°C to elucidate the overall tempering behavior of low-carbon martensites, including the formation of cementite and recrystalli-zation of the martensite. EXPERIMENTAL PROCEDURE Eight iron-carbon alloys with 0.026, 0.057, 0.097, 0.18, 0.20, 0.29, 0.39, and 0.57 wt pct C were prepared as 8-lb ingots by vacuum melting. Typical impurities in wt ppm were 40 Si, 20 Mn, 30 S, 10 P, and 10 N. These alloys were hot rolled to 3 in. plate at 1095°C) (2000°F). The hot-rolled plates were surface ground to remove scale and the decarburized layer, then cold rolled to 0.010 in. sheet. Specimens cut from the sheet were austenitized for 30 min at 1000°C (1830°F) in a vacuum tube furnace in which the pressure did not exceed 2 x 10-3 torr. Chemical analysis of specimens after austenitization indicated no decarburization at this pressure. Immediately before quenching, the furnace was filled with prepurified helium. The specimen was then pushed rapidly through an aluminum foil gasket, which sealed the bottom of the furnace, into an iced-brine bath (10 pct NaC1, 2 pct NaOH). The quenching rate at the M, temperature is about 104'c per sec for 0.010 in thick specimens, as calculated from Newton's law of heat flow2 using a heat transfer coefficient of 25 ft-'. This quenching rate is sufficiently high so that all the alloys transformed completely to martensite throughout the entire 0.010 in thickness and no carbide precipitation occurred in the martensite. All specimens were immediately transferred to liquid nitrogen after quenching and stored there until needed. Tempering below 250°C (480°F) was done in silicone oil baths thermostatically controlled to *;"C. Tempering above 250°C was done in circulating air furnaces or lead pots with the specimens contained in evacuated silica capsules. Electrical resistance was determined by measurement of the potential drop across both a standard resistance and the specimen, connected in series. All resistance measurements were made in liquid nitrogen (77K, -196°C) to minimize thermal scattering of electrons and thus maximize the contribution of impurity scattering to the resistance. Specimen dimensions were 5.10 by 0.19 by 0.025 cm. Although the precision in the electrical resistance measurements was +0.1 pct, the electrical resistivities could only be measured with an accuracy of +5 pct because of uncertainty in the specimen dimensions. Internal friction measurements were performed in an inverted pendulum apparatus at vibration frequencies of either 1.9 or 66 Hz. The specimen dimensions were 5.10 by 0.375 by 0.025 cm. Hardness measurements were made with a Leitz-Wetzlar microhardness machine with loads of 100 g. Specimens were examined by light microscopy after etching in 2 pct Nital and by electron transmission microscopy after preparation of thin sections by electrolytic thinning in a chromic-acetic acid solution.

Jan 1, 1970

By Hans Strack

Electroluminescence of GaAs p-n junctions fabricated by simultaneous diffusion of sulfur and iron was investigated at 77°K. A narrow emission peak with a half width of about 4 kT in the energy range between 1.14 and 1.155 eu was attributed to iron. Other transition elements exhibited light emission in the vicinity of the iron peak, namely nickel between 1.15 and 1.16 ev and cobalt between 1.16 and 1.17 ev. The efficiency of the doping with iron depended on the amoz~nt of arsenic present. A weight ratio of arsenic to iron of 4:l was sufficient to observe the emission lines associated with transition elements. The presence of oxygen reduces the intensity of the light emission. In addition to the levels associated with transition elements, levels at 1.05 and 1.28 ev, probably due to lattice defects, are observed except in diodes fabricated in solution-grown GaAs. THE near band edge emission of GaAsp-n junctions has been studied extensively in the past.' GaAs devices utilizing spontaneous and stimulated near band edge emission are of considerable practical importance. Typical junctions are fabricated by diffusion of a heavily doped p region into degenerate n-type GaAs. Much less work has been done on investigating the radiative recombination via deep levels in lightly doped p-type material. This area is of interest in understanding the performance of GaAs n-p-n transistors. GaAs transistors show remarkable improvement in high-frequency performance and current-gain stability at high temperatures, when iron is added to sulfur during the emitter diffusion process. The present work was initiated to investigate deep-level electroluminescence of iron-doped GaAs p-n junctions fabricated on vapor-phase epitaxial GaAs and on solution-grown GaAs. For comparison several diodes doped with cobalt and nickel were studied. Iron, cobalt, and nickel have an electron configuration of the type

Jan 1, 1968

By Victor G. Hills

CONTRARY to what seems to be the general impression, the island of Cyprus was not named for the metal copper, but the reverse was the case. The origin of the name is entirely lost. The ancient city Kition, the birthplace of Zeno, is supposed to be the same as Kittim mentioned in Gen. x, 4; Jeremiah ii, 10 and Ezekiel xxvii, 6, and Josephus states that this name seems to have been applied to the city and also to the island itself. Cyprus is 50 miles off the coast of Asia Minor. The mountains on the mainland are plainly visible across the sea from where I write six miles from the shore of Morphou bay. It is 200 miles from Joppa the port of Jerusalem, and 250 from Port Said. The shape of the island is like a lizard, the tail pointing directly toward the old city of Antioch near the northeastern corner of the Mediterranean. The island was once heavily timbered. Among the great trees the cedars were said to even excel the famous cedars of Lebanon. The Odyssey refers to it as the "sweet smelling island" and makes other references. But the continual wars of every race and age completely stripped it of its timber, and for centuries it has been woefully barren. There are two ranges of mountains. One borders the north coast and runs out in a slim rocky ridge forming the "tail." The other occupies the southwestern part of the island, the highest point being Mt. Troodes 6600 ft. high, sometimes called Mt. Olympus. Whether or not it be the Mt. Olympus, anyway right around there the ancient gods and godesses frequently "started things." These peaks are in plain sight 10 miles south from where I live.

Jan 1, 1926

By J. J. Mulligan, F. F. Colcord, E. F. Kern

The electrolytic separation of silver and gold has been practiced by the refineries in the United States for a good many years, and probably because of frequent visiting between officials of plants and the consequent exchange of views, operations in the various silver and gold refineries are very similar. We find, for instance, they practically all use electrolytes of approximately the same composition, which, no doubt, is more the result of experience than of studies of electrolytes. At the new electrolytic parting plant of the U. S. S. Lead Refinery, Inc., East Chicago, Ind., considerable attention has been given to the composition of electrolytes, especially to their conductivity and their effect on the character of the silver deposit. We are not aware that anything has been recently published on this subject and are, therefore, presenting such data as we have with the idea that, although it will not be wholly new, it may stimulate interest in the subject. Effect of Copper Content on Conductivity The first work was to determine the specific conductivity of silver nitrate and copper nitrate solutions. Concentrated solutions of silver nitrate and copper nitrate were prepared by dissolving analyzed chemically-pure salts in distilled water, and determining the silver and copper in each. Definite amounts of the concentrated solutions were taken, mixed and diluted to a definite volume. The silver and the copper were determined in each of these solutions and the conductivity was then determined. The plotted results are shown in Figs. 1 and 2. The effect of increasing quantities of silver and copper is readily seen. A comparison of the two sets of curves shows conclusively the benefit of holding the copper content of the electrolyte above 5C g. per liter, as its effect is to increase greatly the conductivity in an approximate propor-

Jan 1, 1926

Advantages to Members of Our Advertising Section.-It is our intention to make the advertising section of the Bulletin as comprehensive as possible, so that members can turn to it for complete information as to where to buy the best mining and metallurgical supplies at the lowest prices. No firms or supplies of dubious reputation are advertised in the Bulletin.. If members, in buying any material, will refer to the advertisement of that material in the Bulletin, or if they do not find it advertised in the Bulletin, will, when ordering, ask the manufacturers why the goods were not advertised in the Institute publication, it will be of material benefit to all of us, because the chief reason why advertisers .are unable to trace direct results is because purchasers do not mention the Bulletin when writing. Finally, if members, when in need of anything whatsoever, will write to the Institute headquarters, an effort will be made to send them a complete list of manufacturers able to supply the desired materials of good quality. The furnishing of these lists will be a benefit to our Advertising Department, as well as to the members. We need .scarcely call attention to the advantages obtained by the members from the motley which advertising brings in, because all this money is returned directly to the members in one form or another.

Jan 7, 1913

By H. W. McCue, Henry Rogatz

Oil.—In the Texas Panhandle, 502 oil wells were drilled during the year 1940, with a total daily initial production of 139,187 bb1.—that is, 137 more oil wells drilled than in the previous year, with an increase in total daily initial production of 8219 bbl. The total daily potential of the field on Dec. 31, 1940, as determined by the Texas Railroad Commission, was 1,375,502 bbl., an increase of 30,825 bbl. over the previous year. On Dec. 31,1940, a daily allowable of 85,050 bbl., which was a decrease of 35 per cent over 1939, was assigned to the field to be produced from 4788 wells. The total amount of oil produced for the year was 26,788,590 bbl., making a cumulative total of 378,960,728 bbl. during the past 19 years. No new oil-producing acreage was discovered. Gas.—During the year, 92 gas wells were drilled, having a combined open flow of 2,402,900.000 CU. ft.; that is, 6 more than the number of wells drilled in 1939, with an increase in the open flow of 204,900,000 cu. ft. per day. The gas production for the year was 670,435,112,000 CU. ft., and the total gas removed from thc ground during

Jan 1, 1941

By Henry Rogatz, H. W. McCue

Oil.—In the Texas Panhandle, 502 oil wells were drilled during the year 1940, with a total daily initial production of 139,187 bb1.—that is, 137 more oil wells drilled than in the previous year, with an increase in total daily initial production of 8219 bbl. The total daily potential of the field on Dec. 31, 1940, as determined by the Texas Railroad Commission, was 1,375,502 bbl., an increase of 30,825 bbl. over the previous year. On Dec. 31,1940, a daily allowable of 85,050 bbl., which was a decrease of 35 per cent over 1939, was assigned to the field to be produced from 4788 wells. The total amount of oil produced for the year was 26,788,590 bbl., making a cumulative total of 378,960,728 bbl. during the past 19 years. No new oil-producing acreage was discovered. Gas.—During the year, 92 gas wells were drilled, having a combined open flow of 2,402,900.000 CU. ft.; that is, 6 more than the number of wells drilled in 1939, with an increase in the open flow of 204,900,000 cu. ft. per day. The gas production for the year was 670,435,112,000 CU. ft., and the total gas removed from thc ground during

Jan 1, 1941

ANNUAL meeting of the Woman's Auxiliary of the American Institute of Mining and Metal-lurgical Engineers convened on Tuesday morn-ing, Feb. 20, the president, Mrs. H. W. Hardinge, presiding. President Hardinge, in opening the meet-ing, said: "I have the honor and great pleasure to welcome you to our seventh annual meeting. It has been a happy year, though I started in fear and trembling. My fear is partly gone and my trembling becomes less as time goes on. Never has a chairman had such splendid cooperation and harmony in her work; no. matter how much was asked nor what the task, I have always received the same answer, `We are with you, of course we can do it.' Often the road has been untried and the way full of snares, but we have all pulled together. Is it any wonder we have had a prosperous year? I cannot thank the governing -board and officers enough for their help." Mrs. Hardinge described her trip through the West last summer, during which she visited many of the local sections of the Auxiliary. She also spoke of the work of the Rossiter Raymond memorial library which has been started as an activity of the Woman's Auxiliary. Mrs. Reynders read the minutes of the last annual meeting, and Mrs. Kemp read the treasurer's report. The latter showed that on Feb. 1, 1922, there was a bank balance of $683.61 and on Feb. 10, 1923, the bal-ance was $947.93. Mrs. Westervelt expressed the sorrow of the Auxiliary for the death -of Mrs. Florence Howe Hall and of Mrs. Levi P. Holbrook.

Jan 4, 1923

By HOWARND N. EAVENSON

THE year 1930 resembled the preceding one in the coal industry in continuing the era of falling prices and 'of the abandonment of unprofitable mines. Practically all coal prices fell, and in the steam sizes during the last half of the year this was particularly true, due to the small industrial demand. No new mines of any size were opened in the bituminous coal industry, but there was a steady increase in the number of cleaning plants of all kinds built in all fields. It is estimated that at least nine million tons per year were added to the previous total of washed coal. The largest washing plant started during the year was that of the Buckeye Coal Co., at Nemacolin, Pa., with a capacity of 650 tons per hour. Fig. 1 shows - the mixing-bin, conveyor galleries, washing-plant and skip hoist, and Fig. 2 the 120-ft. Dorr thickener for collecting the 48-mesh material from the wash water. Dryers are used for drying the steam coal product. The following statement by J. R. Campbell shows the effect of cleaning on Pittsburgh coal in Greene County: "With the advent of the 650-t.p.h. efficient washing plant in Greene County at the Nemacolin mine of the Buckeye Coal Co., it has undoubtedly been demonstrated that the potential coking-metallurgical coals of the county can be brought within the pale of the highest grade high-volatile coals for steel manufacture. A few months' operation indicates that 9% per cent ash in the raw coal can be easily reduced to under 7 per cent ash in the washed coal and the sulfur from 1.60 per cent in the run of mine to 1.20 per cent sulfur in the washed coal.

Jan 1, 1931

By A. B. Johnson, J. S. Browning

The USBM has developed new and improved physical beneficiation techniques for economically recovering potash minerals from high-clay and low-grade ore from the Permian Basin of New Mexico. With the depletion of the high-grade ores a need for changes in industry's standard methods of recovery is a must. Technology may be improved in the beneficiation of the ore prior to mineral flotation and in brine clarification from the desliming phase to effect a reduction of losses of fine potash and brine in the disposal of the clay slimes. This report summarizes the results of these tests and demonstrates the feasibility of producing products that meet the requirements of the agriculture market, namely, 95% KCl equivalent to 60% K2O with recoveries ranging between 80 and 90%.

Jan 1, 1973

By Paul E. Rosten

Introduction This papers describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Co. to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Co. operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously (Lindroos and Koski, 1966; Villar and Dawe, 1975; Koski, 1977). Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and fur¬nished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate¬kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to: (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1981

By C. H. Li, R. D. Carnahan, R. J. Stokes, T. L. Johnston

When silver chloride deforms by pencil glide at temperatures of 26ºand 72°C, grain size has no effect upon the proportional limit and the material necks down to a knife edge under tension. At -196ºC, deformation takes place on fewer slip systems to produce straight slip traces, the flow stress becomes sensitive to grain size and fracture occurs by cleavage from an intergranular source without any reduction in area. THERE are significant differences between the appearance of the slip bands formed in silver chloride and in the alkali halides at room temperature. The bands in sodium chloride, e.g., are fine and geometrically straight, whereas in silver chloride they are coarse and wavy.' Such differences in the slip behavior prompted us to inquire what the effects of grain boundaries might be on the mechanical properties of these solids. As an introduction to a general study of ionic poly-crystal behavior, we have investigated the effect of grain size on the stress-strain relationships in silver chloride at different temperatures. We have chosen silver chloride chiefly because polycrystals can be easily prepared free from cracks and macroscopic voids by conventional techniques. Moreover, as we shall see, the slip behavior can be readily modified by changing the temperature. It will be shown that the effect of grain size on the yield stress of silver chloride is strikingly dependent upon the temperature of deformation and that this temperature effect comes about through a change in the number of slip systems which operate at the onset of plastic flow. EXPERIMENTAL PROCEDURES Polycrystalline tensile specimens were made by recrystallizing cold-rolled AgCl sheet. Thirty-gram quantities of AR grade silver chloride powder were melted in a low heat capacity furnace, cast into cylindrical forms 3/4 in. in dim and approximately 1 in. in length and then extruded with a 16:l reduction ratio into rods 3/16 in. in dim. Extrusion temperatures were varied from room temperature to 350°C. In order to impart various degrees of cold'work to the extruded rod. All extrusions were then cross rolled to sheet 0.040 in. in thickness at room temperature and machined to form tensile specimens having a gage length of 0.750 in. with a width of either 0.250 or 0.145 in.* Annealing was carried out in an air oven at 200°C for periods up to 20 hr. specimens having average grain diameters ranging from 0.024 to 0.40 mm were prepared by varying the extrusion temperature and annealing time in the conventional manner. To obtain specimens with grain sizes larger than 0.40mm, lightly deformed thin prisims of silver chloride single crystals (supplied by Harshaw Chemical Co.) were recrystallized. Grain size determinations were made by an intercept method and revealed that the grains were equi-axed. Laue back-reflection X-ray patterns showed little tendency to form a preferred orientation texture. Specimens which were to be used for the slip band studies were polished by immersion in fresh boiling concentrated NH,OH for 60 sec. They were then etch polished for 10 sec on each side by hand lapping on a stationary velveteen lap wetted with a dilute Hypo solution (5 g of Kodak Acid Fixer in 100 cc H20). Finally the specimens were rinsed in warm water and alcohol, blown dry and carefully mounted in the tensile machine for testing. Tensile tests were performed at three temperatures, namely, 26º, -72º, and -196°C. A screw-driven hard tensile machine was used at a constant strain rate of 0.006 in. per in. per min. Loads were determined with a light- proof ring fitted with A-18 strain gages and extensions were measured with a 0.0001 in. dial gage. Constant level baths of alcohol with dry ice and liquid nitrogen were used to maintain the two lower test temperatures. EXPERIMENTAL RESULTS Reproducibility—In view of the light sensitivity and reactive nature of silver chloride, it was necessary to determine whether reproducibility depended upon either exposure to light or to the condition of the surface. However, during the course of the work it became clear that variation of laboratory lighting

Jan 1, 1962

Advantages to Members of Our Advertising Section.-It is our intention to make the advertising section of the Bulletin as comprehensive as possible, so that members can turn to it for complete information as to where to buy the best mining and metallurgical supplies at the lowest prices. No firms or supplies of dubious reputation are advertised in the Bulletin. If members, in buying any material, will refer to the advertisement of that material in the Bulletin, or if they do not find it advertised in the Bulletin, will, when ordering, ask the manufacturers why the goods were not advertised in the Institute publication, it will be of material benefit to all of us, because the chief reason why advertisers are unable to trace direct results is because purchasers do not mention the Bulletin when writing. Finally, if members, when in need of anything whatsoever, will write to the Institute headquarters, an effort will be made to send them a complete list of manufacturers able to supply the desired materials of good quality. The furnishing of these lists will be a benefit to our Advertising Department, as well as to the members. We need scarcely call attention to the advantages obtained by the members from the money which advertising brings in, because all this money is returned directly to the members in one form or another.

Jan 7, 1913

By Vernon A. Mrak

The Powder River Basin of northeast Wyoming was the first area in the state to receive attention during the early days of uranium exploration. Although the uranium occurrences are many and widespread, most of the known ore deposits are quite small and difficult to mine. As a result of this, detailed regional exploration in the Powder River Basin has been neglected. The uranium ore deposits occur in that part of the Wasatch Formation that is of earliest Eocene age, and they are scattered over an area of about 400 square miles. All uranium ore deposits are associated with red beds or altered sandstones within the Wasatch Formation. Uranium ore was first shipped from the region in 1953. Total production through June of 1965 is 506,257 tons of uranium ore containing 1,922,527 pounds of U3O8. The average grade of ore is about 0.19 per cent U3O8. The major producing area of the Powder River Basin is the Monument Hill district where about 91 per cent of the basin's total uranium ore has been mined. The source of uranium is presumed to have been the Oligocene, Miocene, and perhaps Pliocene tuffaceous rocks that once overlay the area. Joints, fractures, and permeable beds or zones were the passageways for the migration of uraniferous waters from the overlying beds to the Eocene host rocks.

Jan 1, 1968

By R. L. Braun, D. L. Leach

Laboratory experiments simulating in-situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen are reported. Copper extraction and acid consumption data are correlated with temperature in the range 50 to 150°C and quenched pH in the range 0.25 to 2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1977

By AIME AIME

The Bulletin. The Bulletin of the Institute will be issued hereafter monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates tin? membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will lie: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. Lt is probable that a supplementary session of this meeting, will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the farther discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. It is now reasonably certain that the XCVIIth meeting will be held oil the Pacific Coast, including a. visit to the Exposition at Seattle, and various other points en. route going or coming, depending upon the route and program finally adopted. (lore definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Jan 1, 1909

John Langton, New York, N. Y. (communication to the Secretary*):—In Mr. Firmstone's discussion (Trans., xli., 912) the formula he gives for the periodical payment—his equation (2)—may be simplified in form. The expression given by Mr. Firmstone is : q=S(l+ r) 1-(1+r)-(1+r) r which is a simpler form to use in calculations. Where S= principal to bc extinguished. Q = periodical payment or charge for sinking-fund, r = rate of interest per period (i. e., interest on $1 per period). n = number of payments or periods. Kent's Mechanical Enyineer's Pocket Book, under the heading Annuities, equation No. 5, gives : " The annuity which $1 will purchase for any number of ytlars n is * Received Jiily 16, 1911.

Jan 1, 1912

By J. H. Swisher

ALUMINUM deoxidation equilibrium in liquid iron has been the subject of many investigations. Sawamura and Sano1 have written a critical survey of the literature on this subject and consider the data of Gokcen and chipman2 and of d'Entremont, Guernsey, and Chip-man3 to be most reliable. The present study was undertaken to check these data and extend the range of the experiments to lower temperature. The experiments consisted of equilibrating 5-lb Fe-Al melts with recrystallized alumina crucibles at 1580o + 10oC, and analyzing the solidified ingots for aluminum and oxygen. The electrolytic iron stock contained 100 ppm C, 20 ppm 0, and trace amounts of other elements.* The stock was induction-melted in an atmosphere of 5 pet H2 in argon to attain equilibrium between the melt and the crucible. The temperature was measured with a W, 3 pet Re/W, 26 pet Re thermocouple, and the equilibration time was about 4 hr. The results are plotted in Fig. 1 along with curves obtained from the data of d'Entremont et al.,3 for temperatures of 1740o and 1910°C. The present results can be seen to be consistent with the previously reported high-temperature data. The reaction under study is AI2O3 (s) = 2 Al (l) +3O [1] for which the deoxidation product is Kl =[% Al]2 [%O]3 [2] (Under the experimental conditions, Fe A12O4 is not expected to form.4) In Fig. 2, values of log Ki evaluated at 0.01 pet A1 are plotted against 1/T, using data obtained from all the investigations under consideration. The deoxidation product is plotted in Fig. 2 in lieu of the equilibrium constant (normally obtained by evaluating Ki as pet A1 — 0) because of the uncertainty involved in extrapolating to zero concentration. The difficulty in extrapolating the present data for 1580°C is apparent curvature in the log Ki vs pet Al plot. This curvature is perhaps due to the uncertainty in oxygen analysis for concentrations of 5 ppm and below. For the data of Gokeen and chipman,' the extrapolation is also difficult because of experimental scatter. The line drawn through the points plotted in Fig. 2 may be represented by the equation:

Jan 1, 1968

By Truman H. Aldrich

The red, or fossiliferous, ore is found in the Clinton group of the Silurian formation. This group is from 100 to 500 ft. thick in Alabama, and its outcrops have been mapped by the State or the U. S. Geological Survey. In some places, it is entirely missing (doubtless islands in the Silurian Sea). In Etowah County, in part of Greasy Cove and vicinity, the upper seam is a coral reef impregnated with the red ore; in this same county, step faults bring up the ore in three or four practically parallel ridges. In Blount County and on Raccoon Mountain, the ore runs under the carboniferous rocks and outcrops in the valleys. When examining the logs of holes drilled for oil, wherever the drill has gone deep enough, the writer has found the Clinton group underlying the Warrior coal field. The following records of holes drilled primarily for oil, given in Bull. No. 22, Geological Survey of Alabama, show the presence of either ore or red rock, and suggest vast resources yet to be outlined and developed for ore in the future. The locations are given by number on the map. Hole No. 1 was drilled 6 miles southeast of Russellville, Franklin County, by the Woodward Oil & Gas Co. It passed through 160 ft. of the Clinton, but only a small show of red ore was found at 1280-1400 ft. A test well, No. 2, drilled near Atwood, Franklin County, in sectioil 26, township 8, range 14, penetrated the Clinton at 1608 ft. and found 38 ft. of limy red rock, also 8 ft. of some blood red ending at 1820 ft., making 46 ft. of red rock in all. It is reported that some good ore was cut through but this work was done by a churn drill. At least 400 ft. of the formation was classified as Clinton. Well NO. 3, called Frankford Well, was bored by S. A. Hobson and associates in the northwest quarter of section 7, township 6, range 12, Franklin County. At 927 ft., it is supposed to have entered the Clinton; the log is as follows: Ft. Sandy limestone with reddish, high ferruginous argillaceous inclusions 10 Same growing more ferruginous................................ 18 Hematitic limestone......................................... 30 Same with slightly less iron.................................... 23 81

Jan 1, 1925

By V. Kondic, W. M. Rumball

HUNT and Jackson' have recently suggested that binary eutectics might be classified according to the entropy of fusion of the component phases. Such a classification was in fact proposed2 some time ago by the authors and the purpose of this communication is to present some supporting evidence. As pointed out by Hunt and Jackson' typical metals of low entropy of fusion, ?S, tend to form normal eutectics (using Scheil's terminology3). Where one phase is metallic (low ?S) and the other nonmetallic (high AS) then anomalous structures are formed. These anomalous structures may either be regular (e.g., Bi-Sn)or irregular (e.g., A1-Si). Finally Hunt and Jackson suggest that where both phases are of high ?S regular faceted structures are formed. In the proposed classification2 the ratio of the entropies of fusion is taken as the quantitative parameter, i.e., ?Sa/?SB = E, where e > 1.0. An extensive literature survey has been carried out2,4 for reliable photomicrographs of eutectic structures. The structures, numbering 151, have been classified into two classes, viz., normal (i.e., lamellar and rodlike) and anomalous. The latter group has been arbitrarily subdivided into regular and irregular anomalous eutectics. Details and sources of the structures are given elsewhere.2,4 In the absence of better thermodynamic data the value of E has been determined for each of the systems making the following assumptions and approximations: l) The entropy of fusion of solid solutions may be calculated additively;5 ii) Inter metallic compounds are treated similarly but with the addition of the following term for fully ordered structures.5 -4.573(Ni lOg10 Nl + N2 log10 N2) where Nl and N2 are the atomic fractions. It might be argued that the entropies of fusion are meaningless as the eutectic phases form at some temperature (T,°K) below their true melting point (Ta or Tb). As AS, = Lo/To if La the latent heat of fusion of a, is assumed independent of temperature, the actual entropy change AS& is given by La/Te. The ratio of entropies of fusion then becomes Fig. 1 shows E' plotted against cumulative totals for normal and anomalous systems from which it is seen that normal eutectics predominate at low values of E'; e.g., some 90 pct of normal systems lie below E' = 1.5 with 65 pct of anomalous systems above this value. Fig. 1 also shows that the regular anomalous structures occur mostly at low values of c' possibly suggesting growth more akin to normal than anomalous growth. The choice of c as a classification parameter was based on nucleation concepts, it being observed that metals widely separated in Sundquist and Mondolfo's8 nucleation series were anomalous and those close together normal. The basis of these classification views is really outside the intended scope of this communication but it is hoped to explain them fully in the near future.7 Having arrived at this entropy of fusion classification by nucleation considerations it is interesting to note that Hunt and Jackson's ideas are based on growth considerations. Elsewhere one of the authors4 has shown that an even better classification of the metallographic structures reviewed is obtained from purely conventional heterogeneous nucleation concepts. It has been found that systems having a value of the parameter +b less than 0.28 are almost certainly normal and above this anomalous: V, is the gram atomic volume. This parameter is nevertheless closely related to c and c', these being an approximation of p. The parameter is also related to the other classification3,8,9 which have met with any success in the past. All these classifications are to be reviewed shortly by the authorsU7 A significant thing about the classifications based on

Jan 1, 1968