Search Documents

By S. Uludag

Spontaneous combustion of coal has been studied by laboratory techniques using an apparatus in a small-scale laboratory testing. Coal?s inherent characteristics can be measured using Differential Thermal Analysis (DTA) and Crossing Point Temperature (CPT) methods. The DTA curve obtained after testing is compared with actual inherent moisture and its effect on spontaneous combustion has been investigated. It has been found that the Wits-Ehac Index increases as the inherent moisture of the sample increases. Therefore it can be deduced that liability to spontaneous combustion increases with increased inherent moisture. In addition, volatiles have a catalytic affect on self heating immediately after the inherent moisture is reduced. This is identified as stage two in the thermogram. The inherent moisture has a cooling effect during the initial stages of testing and is visible in the DTA thermogram. In addition, while an increase in carbon content means an increase in Wits-Ehac Index value, an ash content decreases the likelihood of on spontaneous combustion. Keywords: Spontaneous Combustion, Differential Thermal Analysis, Crossing Point Temperature, Moisture, Coal, Laboratory Testing.

Jan 1, 2007

The leaching characteristics of a number of Australian uranium ores were determined under acid and alkaline conditions. Ores from the Ranger, Nabarlek and Koongarra deposits in the Northern Territory were readily leached in dilute sulphuric acid. Suitable processing conditions were: leaching at 35-40°C, pH 1·52·0 and redox potential -475 mV for periods of 16-24h with ore ground to 50 per cent -200 mesh CB.S.S.). Ore from the Roxby Downs deposit in South Australia required leaching at 55°C and a redox potential of -650 mV to achieve a satisfactory recovery. All ores contained refractory minerals which were not leached under conventional conditions, limiting uranium extraction to 86-96 per cent.Carbonate leaching of carnotite in calcrete ores from Yeelirrie and Lake Way in Western Australia yielded uranium extractions of at least 98 per cent. Leaching rates were considerably faster than those reported for other applications of alkaline leaching as the slow oxidation step was not required.

Jan 1, 1979

By S. Gallagher, A. Mayton

Introduction The mining industry has long been associated with a high incidence of low back disorders and pain (Klein et al. 1984, Leigh and Sheetz 1989, Brinckmann et al. 1998). It is believed that the higher incidence of these injuries among miners is the result of high exposures to postural demands, heavy manual work, and exposure to whole-body vibration (WBV). Recent work has indicated that miners involved with heavy lifting (especially in restricted spaces or on uneven ground) or who have been exposed to whole-body vibration in undamped seats experience noticeable changes in their spines that are consistent with degeneration of the intervetebral discs of the spine (Brinckmann et al. 1998). As will be described shortly, there is mounting evidence that disc degeneration plays a large role in the development of low back pain, particularly chronic back pain. Until fairly recently, medical doctors generally assumed that back pain was the result of muscle strain, ligament pain, or so-called “trigger points” (Bogduk, 1997). However, research supporting these mechanisms of pain has been very scant. When subjected to scientific scrutiny, none of these mechanisms has been shown to relate to back pain in a convincing manner. On the other hand, there are three mechanisms that have been shown to be highly associated with back pain in controlled scientific studies: sacroiliac pain (present in 13% of back pain sufferers) (Maigne et al. 1996), facet joint pain (present in 15 % of back pain sufferers) (Schwarzer et al 1994), and disc disruption and degeneration (present in 39% of chronic back pain sufferers) (Moneta et al. 1994). The latter mechanism, which bears the highest relationship to back pain that has been objectively demonstrated, will be the focus of this section. Scientists now believe they have a good idea how back pain may develop in cases involving disc disruption and degeneration (Bogduk 1997). As the spine experiences loading during lifting tasks or whole body vibration, the first structure to fail is called the vertebral endplate, which is a structure that attaches the disc of the spine to the vertebral body (Figure 1). The endplate typically experiences a fracture, which the body will attempt to heal by means of scar tissue. Unfortunately, this scar tissue impedes the flow of nutrition to the disc itself (discs are dependent on nutrition from the vertebral bones), and if the supply is reduced sufficiently, the disc will start to degenerate. As this degeneration process proceeds, fissures or tears in the fibers of the disc start to develop. If any of these tears is a grade 3 fissure (Figure 2), an inflammatory response occurs in the disc, which will lead to the well-known sensation of low back pain (Peng 2006).

Jan 1, 2007

By D. H. Diering

The paper takes the reader into the depths of a modern ultra-deep South African gold mine and gives a perspective on the vertical and horizontal extent of the tunnel networks in such a mine. Depending on the mine design layout employed, tunnels once excavated are subjected to various levels of stress change over their life time, and the support requirements are explained. It is suggested that shotcreting is the only viable ultra-deep level support medium, and after looking at the latest developments, the logistical problems are put forward. In an effort to overcome most of these problems, the South African ultra-deep mining industry embarked on a collaborative research programme in 1998. The importance of tunnelling and in particular tunnel support as a critical technology for future successful ultra-deep level mining is stressed. While not yet fully ?on top of? these problems and challenges, our industry is now fully addressing them and we expect to make significant progress during the next 4 to 5 years.

Jan 1, 2000

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2002

Radioisotope x-ray and neutron techniques of analysis can be used for the determination of a wide range of elements in minerals. The most important applications of these techniques to the mineral industry are for onstream analysis of slurries and solids, and for geological assay.The radioisotope x-ray techniques are the more developed ones and two installations for on-stream analysis are in routine use in mineral processing plants in Australia. Neutron techniques are being developed, and should prove valuable for geological assay of large numbers of mineral samples, for borehole logging, and for specific on-stream analysis when the cost of the equipment is warranted.

Jan 1, 1970

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador represents a significant Canadian resource of rare earth elements rich in the sought after heavy rare earth elements (19.8% HREE/TREE). A preliminary economic assessment of the project indicated that the project is technically feasible and economically attractive. A variety of metallurgical test programs have been undertaken which have led to significant streamlining and simplification of the process flowsheet. The improved flowsheet should allow Search to reach production earlier and will use conventional processing equipment. The results of these test programs are presented and discussed in this paper.

Jan 1, 2014

By E. A. van Wyk, M. R. de Villiers

"Mining companies strive to increase and maintain production, while simultaneously remaining competitive in the global economy. Furthermore, they must ensure workers’ safety and maintain good safety records. The use of virtual reality (VR) facilitates the development of tools and systems for various purposes that can improve knowledge and understanding of the work environment. VR is a rapidly growing technology that uses the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and standard 3D graphics card, make VR technology viable and attractive for mainstream training applications. The design, development, and implementation of interactive VR training systems is proposed as an innovative approach to augment safety training. However, in order to assess the impact of such VR training systems it is of particular importance to determine the effectiveness of the design of such systems. This article proposes an evaluation framework for this vital purpose. This framework comprises criteria to assess VR training systems, specifically relating to usability, instructional design, VR systems design, and mining industry context-specific aspects. Although the framework was developed as an evaluation tool to assess effectiveness of the design of such systems, it can equally well be used as a set of design principles to inform the design of VR training systems for mining. IntroductionMining in South Africa has been the main driving force behind the history and development of Africa’s richest and most advanced economy (Coka, 2012). The South African mining industry is frequently criticised for its poor safety record and high fatality rate (Stoddard and Skweyiya, 2016). Inadequate or insufficient training is often cited as a root cause of accidents (Van Wyk and De Villiers, 2009; Tichon and Burgess-Limerick, 2011). Virtual reality (VR) is a rapidly growing technology that utilizes the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction (Webber-Youngman and Van Wyk, 2013). VR is currently being used or investigated as a training solution in a variety of industries. VR technology has developed rapidly and costs have fallen to levels where it can now be considered for mainstream training applications. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and a standard 3D graphics card, make VR even more attractive to mine training centres (Van Wyk and De Villiers, 2009)."

May 1, 2019

By L Maw

New ZealandÆs largest gold producersÆ OceanaGold Macraes Mine is characterised by a large tonnage and relatively low grade operation. To survive in diminishing real gold prices, the operation must focus on a culture of continuous improvement. This paper presents the outcome of a supplier sponsored continuous improvement project known as the Orica Advanced Mining Services project.   In March 2004 OceanaGold (then GRD Macraes) entered into an Advanced Mining Services (AMS) project with Orica Mining Services. The motivating factor behind OceanaGoldÆs need to improve bulk waste productivity and SAG mill throughput was the planned increase in production from five million to 5.4 million tonnes per annum. A stripping ratio of ten to one meant that optimisation of the drill, blast and production functions was paramount.   The primary focus of the project was to optimise the drill and blast parameters to suit the variable rock conditions throughout the mines main operating pit (Frasers Pit). Fragmentation of the ore for presentation at the SAG mill, and cost reduction on the mining of bulk waste movement, were the primary objectives. A number of additional initiatives complimenting the interface between drill, blast and ore production were also established. These included; +        reduced ore loss through delineation of ore boundaries to allow for blast movement; +        established blasting parameters for variable geological conditions, resulting in improved fragmentation; and +        improved asset utilisation by establishing a blasting regime that angled grade control holes to be used as blastholes in the stockworks area.   A year into the project, the philosophy of continuous improvement is now in-grained at the Macraes minesite. As the project continues, the focus is on the further refining of those procedures established, to ensure a continued focus on lower unit mining production costs.

Jan 1, 2005

By J. C. Borland, J. H. Rogerson

Jan 1, 1963

By Carlos F. Perucca

"Potassium is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production.Potash is extracted from buried ancient evaporites by underground or solution mining. This accounts for most of the potassium produced. Another important source is brine from landlocked water bodies, such as the Dead Sea, Salar de Atacama or Great Salt Lake.About 95% of potash produced worldwide is used in agriculture. The rest is found in several other industrial uses, including glass manufacturing, soaps, plastics and pharmaceuticals.Currently, three producers: IMC, PCS and Agrium operate 8 conventional and two solution mines in Saskatchewan, five of which run froth flotation circuits, two heavy media-flotation, two run forced crystallization and one natural crystallization.Potash in SaskatchewanPotash was discovered in Saskatchewan in the early 1940’s while drilling for oil. The deposits lie diagonally across the southern plains of Saskatchewan sloping southerly from a 1,000m depth at Saskatoon to more than 1,600 m depth at Belle Plaine and up to 3,000 m in depth in North Dakota. The known deposits are massive, accounting for more than 40% of the world’s known reserves."

Jan 1, 2003

FOR rapidly marking in geological and topographical features on parish plans, the author has used the Veeder cyclometer with very satisfactory results. A simple Veeder cyclometer, usually retailed at cycle depots at 4s., is fixed to the axle of the front wheel of an ordinary bicycle. The cyclometer is desigued to read in miles and tenths of miles, which are recorded through gearing actuated by a striker on a spoke of the bicycle wheel engaging one of the vanes of the cyclometer once every revolution.By using 80 strikers the reading would be in chains and tenths of chains; therefore the use of 8 strikers gives the reading in chains, utilizing all the figures. The cyclometer is designed to be placed on the right-hand side of the bicycle, and takes up a minimum of space, being only about the size of the top joint of the thumb. With some makes of cycles there is insufficient clearance, so the cyclometer must then be placed on the left side, and the 8 strikers made to engage the top vanes, as shown in the sketch (Fig. 1).Very accurate readings can be obtained by this instrument. The author has found by numerous tests that the maximum error...

Jan 1, 1916

By Andrew Bamber

Between the early 20th Century and the present, the production of mined copper ore has increased from tens of millions of tonnes per annum to several billion tonnes per annum, an unprecedented increase. Contemporaneously, the average grade of mined copper ore has declined from over 2% to approximately 0.5%. Again, in parallel, the price of copper has increased dramatically to reflect the increasing cost of extracting and beneficiating such large amounts of low-grade ore. Within the period the copper price however exhibited several periods of intense volatility, driven by interrelationships between demand and supply, themselves strongly driven by periodic industry developments in the fields of exploration, ore extraction, mineral processing and extractive metallurgy. It is notable that these periods of intense innovation exhibit a strong correlation to preceding periods of price, demand or production volatility. This paper examines key trends in each theme between 1900 and 2018 and draws strong conclusions as to the interrelationship between them. INTRODUCTION The production of copper metal has increased from around half a million tonnes per annum to over fifteen million tonnes per annum over the course of the 20th Century. Contemporaneously, the average grade of copper ore mined has declined from over 2% to approximately 0.5% copper by weight. As a result, the volume of Run-of-Mine (ROM) copper ore required has increased from around ten million tonnes per annum to over a five billion tonnes per annum over the period, an unprecedented increase. The adage is that demand drives supply, that prices rise in times of high demand and/or short supply, and that prices fall when supply catches up with demand. The market sellers in biblical times knew this well; mediaeval market sellers equally. Dutch tulip sellers in the 1600’s experienced both in extremis — much to their dismay — and the great industrialists and early capitalists of the industrial revolution knew this also. Mining recently went through a cycle where investors and producers both believed that the “old” rules did not apply any more and that the industry was in a “supercycle” where prices would continue to rise on the back of increasing demand. However, as the GFC of 2008–2011 showed, this was not to be. Another adage says that we constantly innovate to lower costs of production. Is this true? Do we only innovate to lower cost? Has the true cost of producing copper actually gone down over the century? Or are there other balancing forces at play? Herb Kellogg, in his Centenary address to the American Institute of Mining Engineers (now SME), categorized two types of innovation: ‘Bigger and Better’, and ‘New Process’ (Kellogg, 1970). ‘Bigger and Better’ allows increased production at presumably lower cost; ‘New Process’ supports the same result at presumably the same scale, but at significantly enhanced efficiencies and (therefore) lower cost. It is suggested that both types of innovation are constantly and interchangeably required to achieve the kind of scale-up, at achievable operating and capital cost that the industry has achieved over the period. What can be shown, over this last Century and a bit, is that supply and demand are indeed inextricably linked, price and demand are linked, but so are price and cost of production. And the innovation required to sustain that weaves in between them all, cost-effectively increasing production capacity or lowering the cost of production at the same throughput, and sometimes both.

Jan 1, 2019

Urban development to the south of Sydney is approaching areas of current and proposed coal mining. Already some structures and residential areas are affected by mining subsidence.Subsidence resulting from either conventional pillar extraction methods or longwall mining has been monitored for 15 years to enable the characteristics of the surface deformation to be determined.The vertical and horizontal displacements of survey stations on the surface are monitored and the results arc used to calculate subsidence, changes in slope of the surface, curvatures along the subsidence profile, and the ensile and compressive strains. These features are in turn related to the underground extraction to give a description of surface subsidence and the development of subsidence with time.Subsidence investigations have been carried out over all or part of the workings of six collieries in the Southern Coalfield.Two case histories illustrate the procedure in the investigation of subsidence phenomena. The first example is the study of the subsidence over a series of longwall panels in one seam and the second is a study of subsidence over pillar extraction in two seams one above the other. From the results of the investigations the effects of panel widths on subsidence are determined.This and other information assists mine planning in areas where surface movement and deformation are important considerations.

Jan 1, 1980

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014

The New Zealand Steel Ironsand Slurry Pipeline was successfully commissioned in February 1986. The project includes 18 km of high pressure, polyurethane lined buried pipe. McConnell Dowell Constructors Limited has developed a coupling which has allowed this pipeline to be fully welded. The design and development of the coupling and its application on this project is discussed.

Jan 1, 1986

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By G. J. de Korte

Dense-medium beneficiation of fine (minus 0.5 mm) coal is not a new concept and has been used in South Africa previously. The dense-medium fine coal plant at Greenside Colliery operated for almost 18 years and, despite proving a difficult plant to operate, did succeed in producing a fine coal product with a low ash content of 7%. No other beneficiation process available could achieve this. Dense-medium beneficiation of fine coal was also used in other countries, of which the plants at Homer City in the USA and Curragh in Australia were the best known. The first application of dense-medium cleaning of fine coal was, however, at the Tertre plant in Belgium1. This plant was built in 1957. About nine years later, a second fine coal dense-medium plant was built at the Winterslag Mine, also in Belgium. According to reports, this plant operated satisfactorily for a period of some 17 years.

Jan 1, 2002