Search Documents

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

Efficacy of Enhanced Gravity Separator in Processing Indian Iron Ore Slime The slime sample was subjected to concentration using Falcon concentrator for their enrichment. The effects of three important variables, eg bowl rotation frequency, back water flow rate and per cent solid were studied on the process performance. Increasing the rotation of the Falcon bowl, enable more material to the underflow by increasing the yield, whereas, the iron content decreases steadily with increasing the rotation of the bowl. The increase in the back water flow effectively removes the clay materials from the underflow at the expense of the yield. Similarly, increasing the per cent solid concentration in the feed produces a better product both in terms of yield and Fe content. Results show that EGS/Falcon can be used for processing Indian iron ore slime and producing pellet grade concentrate.

Sep 13, 2010

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By M. Rotz

In the minerals industry today, the ?low hanging fruit? that once existed to debottleneck production and improve recovery, while meeting market needs for quality in mineral processing operations, are more and more difficult to find. Systematic methods for establishing plant mass flow, recovery, operational efficiency and control strategy in context with customer specifications provides the necessary insight and confidence for plant operators to prioritize improvement projects in order to maximize return on investment (ROI) for the site. The evaluation of aggregate and industrial mineral processing plants requires the following steps when projecting cost saving opportunities: collecting background data, conducting a base-line evaluation, analyzing specific unit-operation performance, defining investment options, prioritizing the selected improvement opportunities and the implementing process changes. The following paper describes the approach and challenges of developing an improvement plan for a dry and wet mineral processing operation.

Feb 23, 2014

By D P. Obeng, L Reemeyer, R Holmes

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By M. Gao

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

By Gupta R. C

Direct reduction of iron ore by solid reducing agents have been studied extensively and summarised by several authors (Otsuka and Kunii, 1969; Abraham and Ghosh, 1979; Frauhan, 1977; Rao, 1971; Kawasaki, Sanscainte and Walsh, 1962; Ghosh, 1970; Rao, 1979). While studying the reduction behaviour, it is generally agreed that the reduction occurs via gaseous intermediate, generated by carbon gasification reaction which involves mass transfer, heat transfer nucleation and growth, etc through a) reduction reaction occurring at solid reductant, and b) reduction reaction occurring at solid iron oxides, thus making the overall reduction process very complex in terms of clearly defining the reduction kinetics of the system. In addition to this, practical difficulties like correctness of reaction temperature, (Seaton, Foster and Velasco, 1983) difficulties in isothermal temperature studies of reduction, difficulties in monitoring the reduction process while using gaseous reductants and separation of reduction by volatile matter from overall reduction process make the reduction kinetics more complex (Misra).

Jan 1, 1999

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By A. N. Veltmeyer

"INTRODUCTIONTeck-Corona Operating Corporation's David Bell Mine is located 35 Km east of Marathon, Ontario. In conjunction with its 1000 tonne per day gold concentrator, the company operates an effluent treatment plant for the treatment of mill, mine and site effluents prior to environmental discharge. This paper provides a brief overview of treatment strategies and methods, employed to detoxify final effluent.WATER MANAGEMENTThe tailings impoundment basin, located 3 Km south of the plant site, provides storage capacity for all process effluents and site run-off. Basin supernatant (reclaim water) is recirculated to the plant for reuse as process water, in order to minimize fresh water consumption. As site run-off and limited fresh water intake exceed natural losses due to evaporation, reclaim water in excess of process requirements is passed through the effluent treatment (ET) facility to control tailings basin level by providing regulated discharge of environmentally acceptable effluent. (Figure 1)PASSIVE TREATMENTTo reduce treatment costs and burden on the ET facility, reclaim water is fed to the plant to take maximum advantage of natural destruction processes occurring in the tailings basin.These include: volatilizationphotodecompositionbiological oxidation and precipitationstorm water dilutionConcentrator recovery techniques (Figure 2) are directed toward maximizing gold recovery while limiting the addition and extraction of contaminants requiring disposal and eventual treatment.Currently ore ground to 90% -200 mesh is pre-aerated at pH 9.0 with lime for 18 hours prior to 30 hours cyanidation at pH 9.5 with low cyanide ion excess (70 ppm).Pre-aeration passivates cyanicides prior to cyanide contact. This reduces cyanide consumption and the formation of cyanide complexes. In conjunction with recovery requirements low pH is maintained to retard the dissolution of stibnite into its antimony and sulfide components."

Jan 1, 1989

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By Lars Richter, Franz-Werner Gerressen

"The Eglinton Crosstown Line was conceived as the Eglinton Crosstown LRT, a partially underground light rail line, announced in 2007 as part of the Transit City plan, which included the implementation of six other light rail lines across Toronto.There were 43 stops planned for the Eglinton Crosstown LRT, 13 of which would be underground . For those underground stations a lot of specialty foundation works needed to be carried out. King piles, soldier piles with lagging and secant piles were mainly required fulfilling the tasks of installing the retaining wall system.The paper will focus on the original design and alternative solutions, discussing the benefits and limits of these. It will also explain the installation process in general as well as some specific features related to specific site conditions, e.g. limits in installation depth, soil characteristics etc. The required equipment will be explained showing the benefits and limits.INTRODUCTIONThe Eglinton Crosstown project is a 19-kilometre LRT line that will bring much needed relief to the transit woes of Torontonians. Traversing the city in an east-west slice across the midtown artery of Eglinton Avenue, the Crosstown rail line involves a combination of 15 underground stations and 10 atgrade surface stops. It is one of the largest transit infrastructure projects under way in North America today. Aecon has joined partners ACS Infrastructure Canada, Ellis Don, and SNC-Lavalin to form Crosslinx Transit Solutions (Crosslinx).As with many of today’s mega public transportation projects, the Crosstown LRT follows the Public- Private Partnership (P3) model. Aecon is an equal partner in the $5.3-billion Crosslinx consortium to develop the Eglinton Crosstown LRT project in Toronto. Upon the LRT's completion in 2021, Metrolinx, the region’s transit authority and also the project client/owner, will turn to the Toronto Transit Commission (TTC) to operate it. The impact of this highly anticipated LRT line on commuters in the Greater Toronto Area (GTA) is expected to be dramatic and immediate once the first train leaves the station five years from now. In fact, Metrolinx is estimating that within its first 10 years of service, the Crosstown line will be carrying 5,500 passengers per hour (in peak direction) and making 100 million passenger trips annually."

Jan 1, 2017

By G. Aggistalis, N. Kazilis, C. Rawlings, N. Rachaniotis, S. Raptopoulos, M. Knights, R. Game

The Egnatia Odos (Odos meaning road) is one of Greece’s largest ever highway construction projects and one of Europe’s most important. The Highway will assist in the connection of the Greek Ionian/Adriatic Coast with Turkey and the Black Sea reviving an historic Roman alignment “Via Egnatia” connecting Rome to Constantinople (now Istanbul). There are 74 twin tunnels (60 bored and 14 cut-and-cover) with lengths ranging from 160 m (175 yd) to 4,600 m (5,031 yd) and 100 m (109 yd) to 270 m (295 yd),respectively. The complex geology and resulting physical geography have had a major influence on both the design and construction of these tunnels. This paper describes the management, design and construction challenges of these numerous tunnels.

Jan 1, 2005