Search Documents

By W. P. Blake

FORGING under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various parts of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical ; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

Jan 1, 1874

By R. W. Raymond

AT the Liége meeting of the Iron and Steel Institute of Great Britain, in August, 1873, and also at the Vienna Convention of Mining and Metallurgical Engineers, at the end of August, and at the convention of German geologists, at Wiesbaden, in the first part * Extract from the President's address.

Jan 1, 1874

By J. J. Bodmer

THE substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pit-sand-siliceous sand, as it commonly occurs mixed with gravel-and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (un¬slaked) lime with sulphate of lime, or plaster of Paris. The gray-stone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

Jan 1, 1874

By E. C. Pechin

AT the suggestion of some members of the Institute, attention is called to the record of the working of Dunbar Furnace during the twelve months ending in January, 1874. During this period, with a product of over eleven thousand gross tons, not a single ton of

Jan 1, 1874

By J. J. Bodmer

ALTHOUGH the similarity between puzzolana, or trass, and blast-furnace slag, as seen by comparison of the analyses, is a well-known fact, blast-furnace slag has not been used commercially as a substitute for those cementing materials. The reason, the writer apprehends, lies in the fact that unless such slag is disintegrated or subdivided by rolls, the process must either be too costly, or the material is not in a fit and proper condition for the purpose. In order to produce a reliable slag cement, the slag must be ground together with the lime into an impalpable powder. The subdivided slag must, therefore, be perfectly dry, and, at the same time, friable. The stronger the hydraulic properties of the lime, the more reliable the slag cement will be, and practice has proved, that the slag from a gray-iron furnace gives the best results. The slag cement which has given the results shown in the annexed table, under pressure tests, was composed of six parts of slag, from a blast-furnace producing No. 3 foundry iron, and one part of lime, of medium hydraulic properties. The above-described class of cement bears storing as long as most Portland cements, and the cheapness of its production is self-evident.

Jan 1, 1874

By Frank Firmstone

IN April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Fig's. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised to¬gether, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places. * Etudes our lea Haut Fourneaux, page 108.

Jan 1, 1874

By Thomas M. Dr. Drown

REMARKABLE as have been the direct results of Danks's puddler, there are some indirect and incidental results, which are well worthy of study for their intrinsic value and suggestiveness. The success of Danks's machine is due mainly to the nature of the lining and the manner in which it is attached to the walls of the revolving chamber. Herein lies Danks's merit and good fortune. Given such a lining, and the success of the machine, as far as puddling iron is concerned, could easily be predicted. Other important results have, however, been obtained with this machine, which, though clearly explicable, were, nevertheless, unanticipated. These are the increased yield of bar-iron over the pig-iron charged, and the elimination of phosphorus, which, though not absolutely complete, is yet more decided than in the case of hand-puddling. As regards the increased yield, this is merely what we have a right to expect if we consider the puddling process to consist in the oxidation of the carbon and silicon of the pig by the oxygen of the oxide of iron. That this result is attained, nearly to the extent that the theory requires, in Danks's puddler, and has never been more than partially attained by the most careful experiments in hand-puddling, points clearly to the fact that the contact of the molten pig-iron with the oxide of iron is much more intimate and complete in the one instance than in the other. The action of puddling in Danks's machine may be considered to be twofold first, the removal of the carbon, silicon, and phosphorus of the pig, which is the primary object, and, second, the production of wrought iron direct from the ore, which is entirely an incidental result. Intelligent metallurgists were not long in recognizing in this latter result a fact of deeper import and greater value than the attainment of a perfect puddling process. A new method

Jan 1, 1874

May 219t, 1872. THE Institute assembled in the rooms of the Geographical Society at the Cooper Union, Tuesday evening at 8 P.M. President Raymond called the meeting to order, and introduced Mr. Abram S. Hewitt, who welcomed the Institute to New York. President Raymond, in behalf of the Institute, replied. The President then read the following report of the Council for the past year. The Council respectfully report that the American Institute of Mining Engineers has held four meetings-at Wilkes-Barre, Bethlehem, Troy, and Philadelphia, respectively-all of which have been well attended, and socially and professionally most successful. The proceedings of these meetings having been published in the Engineering and Mining Journal, and sent to all members and associates, are sufficiently well known. Forty-four papers, by twenty-six authors, have been read. These papers embrace s wide range of subjects, and prove the practical character of the proceedings of the Institute. The finances are in a satisfactory condition. By the report of the Treasurer it appears that $1290.10 have been received, $519.90 expended, and that $770.20 now remains in the treasury exclusive of fees for 1872. This fund, it is hoped, will be so increased by voluntary subscriptions as to enable us before long to issue s volume of our most important transactions in a permanent form. The Council has made a favorable arrangement with the Scientific Publishing Company, publishing the Engineering and Mining Journal, by which that journal became the organ of the Institute for the first publication of the proceedings, papers, and notices to members. This arrangement it is proposed to continue through the present year unless the Institute shall otherwise direct. It is not intended to supersede the publication of an annual or occasional volume, but to maintain an interest in the Institute, and to serve the convenience of members while our funds do not permit s more ambitious publication.

Jan 1, 1873

By R. Neilson M. E. Clark

(with map on plate I.) THE coal-beds of Canyon City are situated six miles below the town, upon the Arkansas River. At this point the Rocky Mountains have thrown out from their main ridge two spurs. The one to the north, containing Pike's Peak and Cheyenne Mountain, is known as part of the "Rim Range;" the one to the west and south is known as the `1 Green¬horn Range." Against these syenitic mountains, the later rocks are piled and uplifted; at right angles to the direction of this main uplift is the axis of a lesser plication. On the north, west, and south, the pitch is steep, gradually flattening as it approaches the centre of the basin and rising again to the east at a pitch of about 5°, thus forming a perfect basin, the centre of which is only three miles east of the base of the Greenhorn Range.

Jan 1, 1873

By A. L. Holley

IN order to put sufficient work on steel ingots for rails, they must be reduced from about 12 inches square. As this cannot be done at one heat, they are first drawn down to about 7 inches square, and then reheated and rolled into rails. This first reduction or " blooming," is usually done in this country in a 30-inch 3-high rolling-mill, with movable rolls, so as to get several reductions in each set of grooves. The first of these mills has been running at the Troy Steel-works above a year, with great success. Another at the Cambria Iron-

Jan 1, 1873

By R. H. Terhune

THE enormous production of pig-iron, together with the many difficult and interesting problems with which its manufacture is fraught, has secured to this industry the exclusive attention of scientists with reference to the chemistry of iron, while some of the minor departments of its metallurgy have suffered neglect. Particularly is

Jan 1, 1873

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades : I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. It is a fact which many of you can certify to, that we are wasting fully one-ha f of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop-moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one-quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

Jan 1, 1873

By Eckley B. Coxe

AT the first meeting of the Institute, a paper was read by Mr. Rothwell, calling attention to the importance of at once considering the great waste of anthracite coal under the present system of mining and preparing that fuel for market, and a committee was appointed to examine and report upon the method now in use. About the time the committee were selected, a general resumption of work, after the long strike, took place in the coal regions, and the members of the committee have not in consequence had as much leisure to devote to the study of the question as its importance de¬mands. In the present preliminary report we shall merely sketch out the plan which we propose to pursue in our investigations, so that when our fellow-members are called upon to assist us in our work by fur¬nishing statistics, etc., they may understand more clearly for what object our inquiries will be made. As one of the most practicable methods of obtaining the informa¬tion requisite for an intelligent consideration of our subject, we pro¬pose to send, from time to time, to members and others interested in the mining of anthracite coal, printed sets of questions relating to points under consideration. We would here impress upon our fellow¬-members the importance of filling up these papers as far as they can from their own knowledge. We would, of course, wish each ques¬tion to be answered as fully as possible, but we do not expect every one to answer them all. One question well answered would be of more use to us than the whole paper filled up with answers, many of

Jan 1, 1873

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy ), and the explanation of those facts (geogeny). The facts to observe are: I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. II. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without; massive or thin; the microscopic structure; also whether magnetic or not; soluble or insoluble; fusible or infusible; and the constituent minerals. III. CHEMICAL, that is, the composition of the rocks and of their minerals and their affinities. IV. PALÆONTOLOGICAL, as what kind of fossils are in the rocks,

Jan 1, 1873

By Eckley B. Coxe

(WITH FIGURES ON PLATES II, III, AND IV.) I DESIRE to call the attention of the Institute to two deep vertical shafts, which are now being sunk in Schuylkill County, Pennsyl¬vania, about 1 1/2 miles north of Pottsville. These shafts are of interest to the mining engineer, not only on account of the novelty of the method of sinking adopted, which promises to produce a revolution in that branch of mining engineering, but also as examples of the manner in which such work should be undertaken. GEOLOGICAL SKETCH OF THE TERRITORY TO BE WORKED BY THE SHAFTS AND REASON FOR SINKING THEM. The Mammoth or E Vein of the anthracite coal-measures in that part of the Schuylkill region near and north of the town of Pottsville lies at a great depth below the surface, and has, in consequence, never been worked in that locality.

Jan 1, 1873

By J. W. Harden

APART from the merits of the respective systems of mining under conditions alike, there is much in the nature of the coal and the measures with which it is associated, to make that system which is successfully practiced in one locality ill adapted to that of another; the structure of the coal itself, the roof, the floor, the depth and character of the overlying strata, each exercising more or less controlling influence. Again, in the highly bituminous districts, and with such as have caking coals, where the size of the coal as it comes off the face does not affect its value, as the very smallest of it may be utilized, and in the hard, the open and free-burning coals, in some of which the round only (large coal) is merchantable,

Jan 1, 1873

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack-poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet-for indeed the instrument is easier levelled, and, more-over, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity ; on the other hand, however, that correction

Jan 1, 1873

By Fred Prime

To an association like the one before which I read this paper, few questions can be more important and constantly recurring than the following, viz.: "What economy can be effected in the manufacture of American iron ?" And it is the one with which I purpose to deal in this paper; premising, however, that my object is merely to indicate the direction in which an answer should be sought for, rather than to give it myself. This subject may be divided into two parts; " Economy in the production of pig-iron," and " Economy in the manufacture of wrought-iron;" but it is to the former alone that I shall confine myself this evening.

Jan 1, 1873

By Richard Akerman

(Translated by FREDERICK PRIME, JR., Professor of Metallurgy in Lafayette College, Easton, Pa.) [THE attention now being paid both in this country and Europe to the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this sub¬ject, is a quite sufficient excuse for presenting this paper to the Amer¬ican Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

Jan 1, 1873

By H. S. Drinker

I. The Mines THE first discovery of zinc on the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Röpper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded on the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. It is supposed that the zinc was originally disseminated through the

Jan 1, 1873