Search Documents

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905

By G. E. Christidis, P. W. Scott

The deposits were formed from low-temperature alteration of pyroclastic rocks. Properties investigated include their cation exchange capacity, swelling capacity, pH, rheological properties, the green and dry compressive strengths, shatter index, wet tensile strength, compactability and permeability. It was found that deposits with abundant opal-CT have poor physical properties. The rheological and swelling properties were found to be influenced by the bentonite grade (smectite content) and the degree of disaggregation of the smectite quasi-crystals. The only deposits of high grade which had good foundry properties were those with no opal-CT. Hydrothermal alteration was detrimental to the physical and chemical properties of bentonites in that it decreased the smectite content and the pH and changed the smectite layer charge and the lattice dimensions

Jun 18, 1905

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By A. F. Neil, A. S. Bahaj, P. Watkins, P. M. Hyslop, C. E. Kirby, P. A. B. James

The results of initial work indicate that for 3 of the 5 quarry sands bioleaching reduces the iron oxide content to a commercially acceptable 0.035 wt% Fe20 3, although the time taken to achieve this is 14-22 days against a target leach time of 7 day. Subsequent work has identified strains of Aspergillus niger that are more efficient at producing the array of complexing agents for iron and is yielding excellent and rapid reductions in Fe levels. Potentially, bioleaching offers a more environmentally friendly and energy-efficient process for the removal of Fe from glass-making sands than conventional routes but the production of organic acids by fermentation must be achievable with low-cost substrates such as sugar-beet molasses and lactose permeates for bioleaching to offer a commercially viable alternative to treatment with hot mineral acids. Silica sands usually contain three groups of Fe minerals: iron oxyhydroxides, which comprise crystalline types such as goethite and limonite tending to occur as thin, discontinuous coatings and in cracks and crevices on the surface of the quartz; the assemblage of heavy trace minerals, which include ilmenite, rutile, leucoxene, chromite and haematite, commonly present at levels of 0.1 wt% or less as discrete grains or sometimes cemented to the quartz; and clay minerals cemented in pits on the surface of the quartz and in association with weathered, discrete feldspars. The response of the assemblage of iron minerals to short periods of exposure to hot inorganic acids is broadly related to which group they belong to, those that form coatings being accessible to acid and tending to react rapidly whereas the trace minerals are usually resistant and react very slowly, if at all, and the clays are probably digested. The note reports on a preliminary study of the use of microorganisms to develop an alternative clean technology that will give results comparable to those achievable with hot inorganic mineral acids but with more environmentally acceptable procedures. Various fungi and bacteria produce organic acids when grown in certain media. When these acids come into contact with Fe-stained sand grains the iron is removed as soluble complexes. Several strains of Aspergillus niger have been found to produce organic acids from sugar, predominantly citric, gluconic and oxalic acids, their relative yields depending on cultivation medium and conditions. Sand samples were prepared from five quarries in the UK: Levenseat, Lothian; Redhill, Surrey; King's Lynn, Norfolk; Chelford, Cheshire; and Oakamoor, Staffordshire; ranging in iron oxide content from 0.035 to 0.153 wt% Fe203

Jun 18, 1905

By L Casari

A study of samples from three sectors of the mine, which was worked from Roman times to 1991, revealed different textures, mineral associations and distributions of trace elements in the sulphides. In the last decade before closure, grades of sphalerite concentrate were in the range 51.67-53.30% Zn and 2.21-2.86% Pb and of galena concentrate 69.43-71.62% Pb and 4.70-8.36% Zn, while the estimated by-product germanium content of sphalerite concentrates sold was 300-400 g/t. Passing the different run-of-mine materials through the same concentrator flowsheet produced middlings and tailings during the preconcentration processing. Separate and alternative treatment of run-of-mine products would have yielded improved recoveries of sphalerite and galena and better values of by-product germanium and cadmium

Jun 18, 1905

By G. S. Camm

Gwynfynydd is a small, high-grade black shale-hosted vein-gold deposit. The Chidlaw Link Zone is the only area being mined and contains 24 000 t ore grading 15.2 g/t gold. Within the Link Zone a complex vein structure occurs consisting of a mother vein up to 5 m thick and narrow (less than 0.5 m) leader veins. The former shows minor variations in dip, strike and thickness, whereas the latter show marked changes in all three. The leader veins are hosted within the footwall zone of the mother vein and both are composed of quartz with galena, sphalerite, chalcopyrite, pyrite and minor arsenopyrite. The vein system is transected by a series of cross-vein and intra-vein dip-slip faults. Pockets of gold occur at vein intersections or branches and within the complex footwall zone and are often related to variations in vein attitude and/or geometry. The Chidlaw Link Zone displays a complex, erratic distribution of gold mineralisation and a multi-stage history of structural activity, fluid flow and mineral deposition

Jun 18, 1905

By B. M. England, L. C. Mackey

Magnesia minerals are included in most iron ore sinter mixes to provide the MgO requirements of blast furnace slag. The properties of these minerals have an influence on the eventual sintering properties of the mixes. A detailed study was undertaken of serpentine and dolomite and the use of limestone, olivine and magnesite was also investigated. A consideration of particle properties indicated that as these materials calcine a reduction in size can occur together with cracking and changes in surface properties. These changes could affect the permeability of the sintering bed and sintering performance. Studies of sintering reactions showed that magnesium and calcium, formed from the calcination of dolomite, are extremely mobile before the formation of melt. Evidence suggests that the movement of these oxides into surrounding areas is via a solid-state diffusion process. The diffusion of Ca into the surrounding hematite particles is faster than that of Mg, resulting in the formation of dicalcium ferrite and magnetite or magnesioferrite, the last two subsequently being converted to dicalcium ferrite in the presence of Ca with removal of Mg from the structure as ferroan periclase. Studies of pilot-plant sinters indicated that reaction mechanisms formulated from the bench-scale studies were occurring in actual sintering processes. The differences in sintering reactions between dolomite and serpentine were considered to be the major cause of differences in the availability of lime for bonding phase formation. Pilot-scale studies indicated that the sintering properties of a mix containing dolomite could be improved by increasing the basicity of the sinter mix while keeping the MgO level constant

Jun 18, 1905

By S. Kelebek

DETA exhibits a highly selective depressant action on pyrrhotite without adversely affecting the collectorless flotability of pentlandite and chalcopyrite in nickel-copper ores of the Sudbury region. A simplified Eh-pH diagram has been constructed to illustrate the extended stability of elemental sulphur and to explain the collectorless flotation of pentlandite and chalcopyrite. Cu and Ni ions, which are known to exist on the surface of pyrrhotite, promote the flotation of this mineral whether a collector is present or not. Thermodynamic calculations indicate that the action of DETA involves the sequestration of Cu and Ni ions from surfaces under a wide range of redox conditions; analysis of flotation test filtrate indicates as much as a 20-fold increase in the concentration of Ni and Cu ions. It appears that DETA may enhance the self-hydrophobicity of chalcopyrite and pentlandite by exposing more of the sulphur-rich surface sites for bubble contact in flotation. There are various possible explanations for its depression of pyrrhotite

Jun 18, 1905

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By Seong-Taek Yun, Chil-Sup So, Seung-Jun Youm

The greisen-bordered quartz veins are spatially, temporally and genetically associated with a late Cretaceous granite intruding an early Palaeozoic, limestone-rich formation. Paragenetic data indicate three stages of hydrothermal mineralisation, the first typically in or within 500 m of the granite stock and showing vertical zoning between deeper Mo and higher W, the other two more abundant in the upper and outer parts of the mineralised area. Fluid inclusion and stable isotope data indicate that hydrothermal veins formed over a temperature range of 120-395 degrees C from low-salinity fluids. Early wolframite and molybdenite deposition in stage I occurred at temperatures of 300-395 degrees C from magma-derived, low-salinity, CO2-rich fluid, mainly as a result of fluid boiling and associated CO2 effervescence. Progressively larger volumes of local meteoric water entering the system led to the successive deposition of scheelite in stage I vugs, stage II base-metal sulphides and stage III fluorite-carbonates. Remobilisation of W and its later deposition of scheelite in the outer and shallower portions of the system occurred at 215-275 degrees C and stage II and III mineralisation from lower-temperature fluids that became progressively lighter in stable isotopes. It is concluded that the influx of meteoric water increased with distance from the cooling pluton

Jun 18, 1905

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

By Bakker J. de, P. A. Leest, W. L. Dalmijn, H. J. Glass

The test facility at the Delft University of Technology, in the Netherlands, was characterised. Advantages include the possibility of separating particles with high but different densities up to 9 g/cm3, the ease of adjustment to any required separation density and the absence of moving parts. Simultaneous separation of more than two types of particles is possible and the magnetic fluid is safe and convenient to use compared with other heavy liquids. Disadvantages include loss of magnetic fluid with outgoing particles (cost approx US $10/l) and degeneration of fluid due to bacterial activity, reaction with particles and with surroundings. Only non-magnetic materials can be separated, there is limited potential for scaling up and high investment is required on account of the cost of magnets. Future improvements in the design of the apparatus and the properties of the magnetic fluids can only enhance its attractiveness for commercial applications

Jun 18, 1905

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905

By M. A. Leosson, S. H. Bottrell, R. J. Newton

Sylvite at Boulby is mined 1 140 m beneath the sea and the mine suffers from the influx of water. This is of two kinds: persistent flows originating in the Sherwood Sandstone aquifer and entering the evaporite sequence through fractures in the intervening mudstone, and impersistent flows which are transient in nature and of uncertain origin. Water from the overlying sandstone has become enriched with NaCl and large amounts of KCl and some Mg and Br have been added by interaction with the evaporites. Waters from the transient flows are isotopically distinct from those in the Sherwood Sandstone, being enriched in H and O. They are also saturated with respect to halite and sylvite, but have higher K/Na than the persistent flows and are much more enriched in Mg and Br

Jun 18, 1905

By P. J. O'Connor, V. Gallagher

The addendum, to the paper published in Trans. IMM B, vol.103, 1994, p.B175-B187, acknowledges data from Celtic Gold plc at Navan and apologises for the omission

Jun 18, 1905

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905