Search Documents

For the year ending February, 1920 PRESIDENT HORACE V. WINCHELL MINNEAPOLIS, MINN. PAST PRESIDENTS PHILIP N. MOORE ST. LOUIS, Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX NEW YORK, N. Y. TREASURER GEORGE D. BARRON. . . . ' NEW YORK, N. Y SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y

Jan 6, 1919

Accessions AMERICAN ELECTROCHEMICAL SOCIETY, TRANSACTIONS, vol. 33. Bethlehem, Pa. 1918. AMERICAN ASSOCIATION OF PETROLEUM GEOLOGISTS, BULLETIN, vol. 2. 1918. (Gift of the Association.) AMERICAN YEAR BOOK: 1915. Edit by Francis G. Wickware, New York. 1919. (Gift of D. Appleton & Co.) ANNUAIRE DE LA HOUILLE BLANCHE FRANCAISE. ` By M. Auguste Pawlowski. 2d year. 1918-1919. Paris. (Gift.) BLACK DIAMOND, Vol. 60, Jan.-June, 1918; vol. 61, July-Dec., .1918. (Gift.) Chicago. CANADIAN MINING INSTITUTE, TRANSACTIONS, vol. 21. 1918. Montreal, Quebec. COMPTES-RENDUS DE L'ATHÉNÉE LOUISIANAIS, vol. 4, No. 3. (Gift of Wm. Beer.) EFFICIENCY OF NATURAL GAS AT Low PRESSURES. Abst. of testimony of Samuel S. Wyer before the Corporation Commission of Oklahoma, February 4, 1919. Printed by Empire Gas & Fuel Co., Kansas City, Mo. GEOLOGICAL. INSTITUTION OF THE UNIVERSITY OF UPSALA, BULLETIN. Edit. By Hj. Sjögren. vol. 14, 1917; vol. 15, 1916; vol. 13, pt. 2, 1916. (Gift.) HYDROGENATION OF OILS. Catalyzers and catalysis and the generation of hydrogen and oxygen. By Carleton Ellis. 2d edition. New York. 1919. (Purchase.) INSTITUTE OF METALS, JOURNAL, vol. 26. No. 2. Edited by G. Shaw Scott. London. 1918.

Jan 6, 1919

By Wilford Stork

CERTAIN influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,1 such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is really burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book3 The work of J. E. Johnson, Jr., has revolutionized

Jan 6, 1919

Among the recent bulletins are the following, which. may be obtained from the Superintendent of Documents, Government Printing Office, Washington, D. C. BULLETIN 127. Gold dredging in the United States, by Charles Janin. 1918. 224 pp;, 63 pls., 23 figs. 50 cents. BULLETIN 161. California mining statutes annotated, by J. W. Thompson. 01918. 312 pp. Paper cover 20 cents. BULLETIN 169. Illinois mining statutes annotated, by J. W. Thompson. 1918. 594 pp. Paper cover 35 cents. The. Potash Situation, by A. W. Stockett. 13 pp. Preparation of Crucible Graphite, by George D. Dub. 27 pp. National Importance of Allocating Low-ash Coke to the Manganese-alloy Furnaces, by P. H. Royster. 4 pp. Production of Ferromanganese in Blast Furnaces, by P. H. Royster. 31 pp. Production of Spiegeleisen in Blast Furnaces, by. P. H. Royster. 19 pp.

Jan 6, 1919

As it is the plan of the War Department to return 400,000 soldiers a month during the next four months, Colonel Arthur Woods, Special Assistant Secretary f War, has requested the Engineering Societies to assist the Government by soliciting their members to advise the respective societies, at the earliest possible moment, f any place where companies can employ returned soldiers. This request applies not only to the professional men who are returning but also to the miners, mechanics and other skilled labor among the enlisted men. Army discipline has not only made these men think more quickly but also more willing and obedient workers. The whole training has been conducive to regular habits and clean living steadying these men and fitting them to meet emergencies more quickly and has instilled more loyalty to their superiors and to their jobs. Further, the military instruction they have received has increased the men's powers f concentration. The War Department cannot too strongly bring before the employers of skilled labor the fact that the employment f discharged soldiers will be advantageous to the employer and economically beneficial to the country. The following is a list of the vocations of the men who are now returning:

Jan 6, 1919

The Fifth Annual National Exposition of Chemical Industries will be held in Chicago at the Coliseum and First Regiment Armory during the week of Sept. 22. It was decided to hold the exposition in Chicago, this year, for two reasons: The U. S. Army commandeered the Grand Central Palace Exposition Building in New York, immediately on the close of the last exposition and converted it into a receiving hospital, the use for which is now, happily, nearly ceased; and it was thought that the Exposition would succeed in bringing about a greater development of chemical industries in the Chicago district and the adjoining states. The Advisory Committee of the Exposition consists of: Charles H. Herty, Chairman, Editor Journal of Industrial and Engineering Chemistry; Raymond F. Bacon, Director, Mellon Institute; L. H. Baekeland, Member Naval Consulting Board; W. D. Bancroft, President, American Electrochemical Society; Henry B. Faber, Industrial Filtration Corpn.; Ellwood Hendrick, President, The Chemists' Club; Bernard C. Hesse, Chemist, General Chemical Co.; A. D. Little, President, Arthur D. Little Inc.; Wm. H. Nichols, President, American Chemical Society; R. P. Perry, Vice-president, The Barrett Co.; H. C. Parmelee, Editor Chemical &; Metallurgical Engineering, G. W. Thompson, President, American Institute of Chemical Engineers; T. B. Wagner, Vice-president, U. S. Food Products Corpn.; M. C. Whitaker, President, U. S. Industrial Chemical Co.; and Charles F. Roth and Fred W. Payne. There is also added a special Chicago committee consisting of L. V. Redman, W. D. Richardson, A. V. H. Mory, Carl S. Minor, F. W. Willard, and Wm. Hoskins; the managers, as in the past, are Charles F. Roth and Fred W. Payne.

Jan 6, 1919

Through the courtesy of Mr. J. H. Batcheller, we are able to give the following extracts from a letter written by Mr. Caetani: It has been a nice idea of yours to collect for me all those scraps of news I received a few days ago and to send me such a long interesting letter. In four years war I have had practically no news. Burch wrote several times but several of his letters were lost and so mine. I believe I even wrote to you. Much has changed since our last days in Telluride; here and there many have disappeared. Of myself I will tell you in a few words: for a year I was in Cadore(?), where I had the good luck to do to the others what they wished to do to me, and had good luck on my side. Then I went to Macedonia for 5 months, did little fighting but lost my faithful fellow officer and companion.

Jan 6, 1919

The sixty-fifth Congress created a commission on classification and standardization of wages of Government employees consisting of three members of the Senate and three ex-members of the House of Representatives: The Chairman of the National Service Committee has been notified orally by the Vice-chairman that when said Commission reaches the consideration of engineers' salaries in the Government service, request will be made for assistance of Engineering Council. As it is probable that this request will be received prior to the June meeting of Council, it is recommended that action be authorized concerning the appointment of a suitable committee of Council to undertake this work.

Jan 6, 1919

H. G. KNOX,* Norfolk, Va. (written discussion?).-There is one subject that Mr. Hobart seems to have inadvertently omitted from his very valuable paper, and that is corrosion. The shipbuilder, perhaps more than anyone else, has constantly to guard against it, our chief reliance being paint and galvanizing, where practicable. The corrodibility of a welded. joint is salt water must be determined before deciding whether this type of construction is to supersede riveting. At the present time, this question cannot be answered, although considerable work has been started in an attempt to arrive at a conclusion. The British Admiralty and several British shipbuilders have studied it extensively. Their experiments and conclusions have been very carefully followed and reported in this country by Naval Constructor Goodall of the British Navy. To date, these show that no undue fear need be felt from corrosion. At the Norfolk Navy Yard a series of plates welded with various electrodes were submerged in dilute sulfuric acid, such as is used in cleaning prior to galvanizing. While this test may not be conclusive in any quantitative way, it does show a marked difference in the corrodibility of welds made with different electrodes tinder different conditions. To thaw any conclusions from this accelerated this accelerated test would be, however, ill advised. In riveted joints, the exposed heads and points of the rivets always show the greatest tendency to corrode. This is clue to two reasons: first, as they are raised above the surrounding surface the paint is more susceptible to abrasion; and, second, electrolytic action is set up between rivet and plate. These same reasons lead us to expect a tendency of the welded joint to corrode. Various methods have been suggested for decreasing the probable inherent corrodibility of the weld, in addition to the customary coat of paint. These generally embody the introduction of alloys, principally copper; into the electrode material. Plating the electrode with copper is not effective in that the deposited copper segregates in the weld and actually increases the electrolytic action. As far as is known, no extensive test on the so-called copper-bearing alloy steels, which might be made up into electrodes, has been carried out, but when obtainable, electrodes of this alloy will be subjected to service tests.

Jan 6, 1919

G. F. COMSTOCK (author's reply to discussion *).-The discussion of this paper has been of such volume and interest as to constitute in itself a sufficient excuse for the paper, even though the paper itself may have been as much in error as some of its critics have maintained. Mr. Howard does not appear to realize some very practical facts that the opponents of his theory have advanced. Among these are: the coarsely crystalline fracture of the nucleus of a transverse fissure, so different from the smooth fatigue break around it; the occurrence of fissures in large numbers in certain heats or rollings of rails, while other heats or rollings do not develop them; and the much smaller proportion of transverse fissures found in rails rolled .from reheated blooms as compared with direct-rolled rails. These facts are not explained by Mr.

Jan 6, 1919

The following is an incomplete list of members and guests who called at Institute headquarters during the period Apr. 10, 1919, to May 10, 1919. Arthur K. Adams, Spencer, Mass. Ensign Floyd D. James, U. S. S. Fulton. W. T. Bates, New York City, N. Y. J. Harry Johns, Thorsden, Woking, A. D. Brokaw, Washington, D. C. England. E. H. Clausen, San Francisco, Calif. W. F. Jones, Rock Springs, Wyo. W. M. Corse, Mansfield, Ohio. E. L. Lasier, Washington, D. C. E. O. Daue, Philadelphia, Pa. John M. Lovejoy, New Rochelle, N. Y. G. D. Dub, Washington,, D. C. 2d Lieut. James F. Magee, Lancaster, S. B. Eaton, Dover, N. J. Pa., Sherman Eaton, Smethport, N. C. Ernest Marquardt, Casper, Wyo. J. A. Endweiss, La Jolla, Calif. Geo. B. Marshall, Abangarez, Costa Edgar W. Engle, North Chicago, Ill. Rica. 2d Lieut. Maxwell E. Erdofy, New York Benj. L. Miller, So. Bethlehem, Pa. City, N. Y. Major Desaix B. Myers, Camp Mills. Chas. A. Fellencer, Allentown, Pa. Edmund Newton, New York City, N. Y. Arthur Feust, Joplin, Mo. Seely B. Patterson, Jr., Allentown, Pa. Ensign Harold P. Ford, U. S. S. Radnor. Wm. R. Pearson, New York City, N. Y. A. D. R. Galloway, Accra, West Africa. Harold C. Price, Langeloth, Pa. R. C. Gosrow, Milwaukee, Wis. T. C. Roberts, East. Orange, N. J. C. A. Grabill, El Paso, Tex. P. H. Royster, Washington, D. C. Hobart A. Hanks, San Francisco, Calif. W. H. Staver, New York City, N. Y. John L. Henning, Lake Charles, La. N. L. Wimmler, Bangkok, Siam. 1st Lieut. J. Parke Hook, Philadelphia, Capt. Jay P. Wood, New York City, Pa. N. Y. An item in the May Bulletin made it appear that Frank W. DeWolf had just become connected with the State Geological Survey of Illinois. This was one of the inadvertences of war. Mr. De Wolf has been Director, or Chief, of the State Geological Survey for approximately ten years. Through the courtesy of the Governor of Illinois, lie was loaned to the Bureau of Mines for about seven months, after which period he resumed his former position.

Jan 6, 1919

Prof. Frank H. Probert, dean of the College of Mining of the University of California, visited the mining areas in the devastated regions as a member of the Bureau of Mines committee, which is studying the problems presented in the rehabilitation of mines there. He says that the absolute destruction of the coal mines in the Pas de Calais section makes it-necessary to use either the Westphalia or the Saar valley coal. The Saar mines, however, produce a poor quality of coking coal: therefore, it will not be possible to operate blast furnaces very efficiently unless provision is made for the introduction of better coal. He believes

Jan 6, 1919

HENRY TRAPHAGEN, * Toledo, Ohio (written discussion t).-The occurrence of flakes in steel is a perplexing problem, if we consider this condition as a disease rather than a symptom. But if considered as an exaggerated phase of a common disease, flakes will be recognized as old and well-known enemies. I have frequently found flakes in open-hearth steel, converter steel, and even electric steel; and not only in the so-called alloy steels but in dead soft 12-point carbon castings. In fact, I have some twenty flaky test bars that came from a foundry that manufactures converter steel castings. The physical characteristics of such material are striking in their constancy, for the yield point and elastic limit are always high, the elongation is variable, and the reduction of area is nearly always negligible. Soft steels of this kind can easily be bent to an angle of 150° and the only bad symptom is the appearance of incipient cracks on the surface; when the carbon exceeds 30 points, the bending qualities are seriously affected; and when the carbon reaches the neighborhood of 50 points, the bars are generally pulled short. The elongation is peculiar in that it seems to take place along the whole length of the bar, giving a crinkly appearance such as is found in cast brass and monel metal. Of course, this elongation only takes place in the softer varieties of steel. I have stated that flakes in steel represent exaggerated symptoms of a common disease, and that disease is the presence of higher oxides of iron. In every instance that has come to my attention, this condition is coexistent with the presence of oxides in some form. In open-hearth practice when this condition occurs, almost invariably it will be found that the metal has been loaded with ore or that tons of rusty turnings were being melted. In converter practice, one of three conditions is nearly always present: bad cupola practice, the use of oxygenated pig iron, or faulty tuyeres. With the electric furnace, my experience is quite limited, but the few examples of flaky electric steel that have come to my notice were made from a charge of turnings and low-grade light scrap.

Jan 6, 1919

There were present twelve- Directors, the Secretary and the Assistant Secretary of the Institute, and fifteen guests. A committee of three was appointed to draft a suitable resolution of memorial of the services of Joseph Esrey Johnson, Jr. The committee consists of Joseph W. Richards, Chairman, J. V. N. Dorr and Allen H. Rogers. William R. Walker was elected a Director in place of J. E. Johnson, Jr., and Edwin Ludlow was elected a member of the Executive Committee in his stead. George C. Stone was appointed Chairman of the Committee on Membership in place of Mr. Johnson. The following resolutions were then adopted: RESOLVED, That a special business meeting of the Institute be and the same hereby is appointed to be, held at the office of the Institute, No. 29 West 39th Street, Borough of Manhattan, City of New York, on the 27th day of June, 1919, it 8.30 o'clock in the P. M. to consider and take action upon the proposal to change the name of the Institute to "American Institute of Mining and Metallurgical Engineers, Incor-porated," and the further proposal to extend the corporate purposes of the Institute so that it shall, in addition to its other powers, be empowered to promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of, those employed in these industries, by all lawful means.

Jan 6, 1919

Underground Transitmen.-Two transitmen with experience in shaft mines; need not be full grown engineers but entirely capable of doing accurate instrument work. Location Middle West coal mines. R-419. Draftsman.-Kentucky. $150 per month.. Extensive experience in map work and construction work, such as is found in and about coal-mining operations. Send sample f work and state whether or not married. R-606. Mine Transitman.-Kentucky. $140 per month. Considerable experience in and about coal mines; must also be a fair draftsman. Send sample of work and state whether or not married. R-607. Draftsman.-West Virginia. Experience on mine 'mapping and construction work, for position with coal and coke company. R-609. Civil Engineer.-China. Salary depends upon man. Technical education and training in general engineering and building construction. Man about 30 .years of age desired, preferably unmarried. The various engineering construction in which this firm is engaged are as follows: Investigations, inspections, reports and valuations, design and supervising of construction for industrial plants and bldgs., power plants, difficult foundations, bridges and steel structures, wharf and deck construction, river and harbor works, investigating and development

Jan 6, 1919

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

The plan for establishing relations of American industry with national labor on a definite basis so closely follows the channels of the efforts of Engineering Council, principally in the classification and compensation work, that it is of special interest to the engineering profession. The principles laid down under the following headings are about to he submitted to a referendum vote of the membership of the Chamber of Commerce of the United States. These principles were prepared by a special committee of the Chamber of Commerce after a long period of study of the entire subject of industrial relations. 1. Industrial enterprise, as a source of livelihood for both employer and employee, should be so conducted that due consideration is given to the situation of all persons dependent upon it. 2. The public interest requires adjustment of industrial relations by peaceful methods. 3. Regularity and continuity of employment should be sought to the fullest extent possible and constitute a responsibility resting alike upon employers, wage earners, and the public. 4. The right of workers to organize is as clearly recognized as that of any other element or part of the community. 5. Industrial harmony and prosperity will be most effectually promoted by adequate representation of the parties in interest. Existing forms of representation should be carefully studied and availed of in so far as they may be found to have merit and are adaptable to the peculiar conditions in the various industries. 6. Whenever agreements are made with respect to industrial relations they should be faithfully observed. 7. Such agreements should contain provision for prompt and final interpretation in the event of controversy regarding meaning or application.

Jan 6, 1919

RAYMOND M. Howe (author's reply to discussion*).-Dr. Unger states that magnesite will hardly supersede dolomite in fettling after a heat; that it is hard to believe a slag composed of oxide of iron containing about 6 per cent. of phosphorus is the active corroding, agent in a boil in a furnace; and that boiling cannot be said to be the result of the chemical action of a high-phosphorus slag on a basic bottom. These are well-established facts that no one would venture to question. The authors were misinterpreted in the statement that "in the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in resistance to slaking," etc. On the contrary, the position has been taken throughout that while a low lime content is advantageous, the presence of several per cent. of iron oxide (an impurity), is necessary in order to confer the proper bonding and sintering properties in dead-burned grain magnesite to be used for furnace hearths. We cannot subscribe to the view that pure magnesia is no better fitted for a refractory than pure lime,' nor that the pure natural varieties of magnesite; such as Grecian or Washington, must necessarily be burned with silica and oxide of iron to produce a satisfactory material. On a small scale, pure magnesia has been satisfactorily used as a refractory in the form of crucibles. In the production of dead-burned grain magnesite from the Grecian or Washington mineral, iron oxide is added but the addition of silica is neither customary nor desirable. It is possible to manufacture brick of good quality from both the Grecian and the Washington material without adding either silica or iron oxide, providing they are burned at a sufficiently high temperature. This is regularly done on a commercial scale both in America and abroad when brick of. exceptionally high refractoriness or special purity are desired. The following analysis is of an English brick of Grecian magnesite which is extremely low in all impurities.1

Jan 6, 1919

STANDING COMMITTEES Executive-A. R. LEDOUX, chairman. Membership-GEORGE C. STONE, chairman. Finance-J. V. N. DORR, chairman. Library-E. GYBBON SPILSBURY, chairman. Papers and Publications-BRADLEY STOUGHTON, chairman. Nominations-POPE YEATMAN, chairman.

Jan 6, 1919

CHARLES F: WILLIS,* Bisbee, Ariz. (written discussion?).-An employment department operated only with the object of relieving the foremen from hiring and for the purpose of centralizing record keeping is not likely to be entirely successful, and is doing but a small part of the good that practice has shown is possible; although it was .probably a desire to save time and to conduct the business more conveniently that led many mining companies to centralize their employment department. The ultimate object, however, is the reduction of labor turnover, by obtaining men better qualified to fill the positions to which they are assigned, by following up their work and providing for transfer to other departments or for promotion, if advisable, by reducing the number of quits for inconsequential reasons, and by supervising such laying-off as is necessary in such a way that the permanent force is not upset. It provides a stability 'of employment, free from favoritism and paternalism, probably the best form of employment insurance that we can have. The value of the employment department is in direct proportion to the breadth of its supervisor, his ability to estimate and place men, his sympathy in dealing with their petty troubles, and his analysis of quits and the reasons therefor. There is probably no better index of the soundness of the industrial relationship between the employee and the employer than the reasons why men quit; an intelligent, unbiased analysis of these reasons tells where corrective measures are necessary. In nine cases out of ten the reasons are small grievances, easily corrected, and are things usually overlooked by mine officials.

Jan 6, 1919