Search Documents

By E. G. Meiter, S. H. Katz

"Railroad locomotives produce heat, gas, and smoke, which cause considerable discomfort to engine men and firemen while passing through tunnels. In order to try and improve these conditions, the Bureau of Mines has investigated the composition of atmospheres in cabs of freight locomotives while in tunnels; and some of the higher temperatures in the cabs were noted; physiological effects upon men were determined and gas masks and respirators were devised to eliminate the effects of irritating and poisonous gases and smoke. Those investigations were conducted in tunnels of the Baltimore & Ohio, Pennsylvania, and Union Pacific railroads; while that described in this paper was carried out in tunnels of the Chesapeake & Ohio, Railroad, situated in the Blue Ridge and Allegheny Mountains in Virginia and West Virginia, Freight locomotives used by this railroad are of the Mallet type, which have two separate cylinders: and two separate sets of driving wheels on each side. In locomotive language they are of the 2-6-6-2 type. All of the cylinders act as simple engines when starting or in slow, heavy hauling; but at faster speeds the pair of cylinders on each side operate compound, Mallet locomotives are the largest and most powerful now operated.The tendency in train operation has always been to increase the burden upon locomotives, Present traffic needs frequently load even the Mallet engine to capacity, and yet the weight of trains tends to increase. It has been suggested as a means of securing greater power units that Mallets be constructed to operate only as simple engines. This would increase the amount of steam given off as the amount of coal burned and the resulting volume of flue gas emitted."

Jul 1, 1924

"Human accidents are caused by production accidents, generally ones (such as derailment of cars, falling rock, etc.) that have occurred numerous times before an employee was actually involved. Prevention of human accidents is, one of the essentials in cutting operation costs, and advocates of safety are studying economics to assist them in their work of preventing accidents.Workman's compensation insurance or compensation for human accidents is a true operating cost, and is the only purely tangible measure available which gives a measurement of the cost of accidents even though, as will be pointed out later, it represents but a portion of the total cost of human accidents.In using premiums paid for compensation insurance as a measure of the cost of accidents, it must be kept in mind that most insurance laws, as pointed out in a former paper (Serial 2590 of the Bureau of Mines) provide a waiting period before compensation for the lost-time wages starts, with the compensation limited to definite percentages of the wages. The waiting period and limited compensation combined tend to limit the amount paid to an injured workman who, if he receives 1/3 of the lost-time wage, will probably have been reimbursed as high as the average injured workman.The total or complete economic cost of human accidents, must include, in addition to compensation paid for lost time, and the portion of the lost-time wage suffered by the workman for which he is not compensated, the additional cost to the company through-(a) temporary decreased production by the breaking down of the morale, etc., (b) the breaking in of a new employee which is admittedly expensive,(c) the increased liability of human and production accidents caused to or by the new employee.Another charge against accidents, which is not included in the compensation payment, is the economic loss through the killing of as workman who has no dependents. Few of the States' laws require any compensation except burial expenses to be paid for fatalities to persons having no dependents. It is estimated by the United States Bureau of Labor Statistics that the economic loss through a fatality is 6000 shifts. If each fatality was compensated for this amount of time and at half-time wages, using an average wage of $5.00 per shift, the compensation for fatality based on the economic loss would be $15,000. but the average actual compensation paid for each fatality is about $3,000."

Jul 1, 1924

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By F. C. Gregory

"The ""safety bonus"" in metal mining is a sum in addition to the regular wage, paid to foremen or bosses for keeping the accident rate down to a specified minimum. It has been used with success for some time by certain companies as a regular part of their safety work. It is desirable from the employer's point of view in that the desired results in accident reduction must be accomplished before the bonus is earned; and from the standpoint of the recipient, in that he receives a reward for the additional effort which he has put forth in order to earn the bonus.While this paper relates to the safety bonus as applied in the metal mining industry, the bonus system discussed herein will apply equal well to coal mining, oil-field work, and other mineral industries.Various estimates have been made as to the percentage of accidents that can be prevented through physical safeguards, adoption of safe working methods, and other safety measures which can be initiated and carried out wholly through the management or the safety department. This percentage will always be a vari¬able according to the local plant and conditions. But all who have been engaged in accident prevention agree that such work alone cannot bring the accident fre¬quency down to where it should be, and that it is very necessary to work directly with the workmen, in an effort to make each individual do his share in making the work safe. In this latter phase of the work, the boss who has immediate super¬vision of the men is the one who can do the most, since he is in daily and frequent contact with the men while they are at work. In the metal mines, the shift and stope bosses are the key men; in the oil fields, the ""tool-pushers"" or sub-foremen, and the same applies to all industries. So it becomes necessary to keep these sub-foremen constantly interested in accident prevention, both because they are in personal touch with the men and because they are responsible for production and hostile to any plan which they think will interfere with their output. In large organizations it is the shift boss who represents the company and its policies to the man on the job."

Jun 1, 1924

By A. W. Fahrenwald

"About two years ago the Bureau of Mines, Department of the Interior, and the University of Idaho undertook an investigation of classification in its relation to table concentration of Idaho ores. The cooperation of the management of the Bunker Hill & Sullivan Co. in placing at our disposal their West Mill and facilities as desired, offered an unusual opportunity for studying the field of hindered classification in its practical and economic relation to table concentration.It has been shorn theoretically, and demonstrated experimentally, that ore products are more easily and economically concentrated on tables if the natural feed, consisting of various minerals and of all sizes of particles of each mineral, be classified or grouped into a series of products in which the mineral particles of greatest density are small in diameter relative to the diameter of the mineral particles of lesser density. Products in which the maximum difference in diameter of light and heavy minerals occurs are to be obtained only by true hindered settling classification. To our knowledge there has never been a really good hindered settling classifier used in practice and the present tendency seems to be to by-pass any attempt at such classification.After a careful study of the nature of hindered classification and of the requirements for hindered settling in practice, a classifier has been developed that takes fullest practical advantage of the widely known, but generally only meagerly understood, condition of hindered settling so well analyzed a number of years ago by Dr. Richards.The present paper presents briefly some of the more important practical results accruing through the investigation."

Jun 1, 1924

By D. B. Gawthrop

"In connection with the proposed use of Cordeau-Bickford to fire L.O.X. (liquid oxygen explosives) in well drill holes, the question has arisen as to the effect of very low temperatures on (1) the rate of detonation of Cordeau-Bickford; (2) the sensitiveness to detonation of its TNT filling; and (3) the lead covering of Cordeau-Bickford.The Cordeau-Bickford used in this investigation was the standard 6 mm. size, such as is regularly used in blasting, and was manufactured and furnished by the Ensign-Bickford Company, Simsbury, Conn. All pieces tested were taken from rolls, all of which were from the same melted batch of TNT in order that all the pieces tested might be as nearly identical as possible.Different portions of this Cordeau-Bickford were tested plain (not countered), countered, and double countered. The countering and double countering was carried out by the manufacturer prior to shipment.The determination of the temperature at the instant of making a test was accomplished by the use of a Leeds and Northrup potentiometer and copper constantan thermocouples. Each couple was made from No. 28 B & S gage wire with short junctions. One junction was inserted in a hole drilled by a No. 60 drill through one lead wall of the Cordeau-Bickford to approximately the opposite wall, so that this junction was in the center of the TNT filling while the other junction was immersed in ice water. The potentiometer readings in millivolts were converted to °C. from the calibration curve of the thermocouple wire,"

Jun 1, 1924

By W. M. Weigel

"Sand is one of the commonest materials for industrial use, not only as a building material, but in many industrial processes. The general name applies to all grades, from the comparatively impure, unsorted product used in concrete, to especially sized products of extreme chemical purity. Various definitions have been proposed, all more or less open to objection, as they fail to cover special applications. One is: ""Sand - The fine granular material naturally or artificially produced by the disintegration or crushing of rock or slag"". This does not fit the definition of sand as understood by geologists, who consider sand only as a naturally formed product. Another is: ""Sand - The fine granular material naturally produced by the disintegration of rock"". This does not take the chemical com-position into account, and for practically all uses, except in concrete and plaster products, a material composed predominantly of silica or rather quarts is implied.Sand for special purposes usually requires different methods of preparation from those where the ordinary mixture of sizes as naturally occurring are suitable. One of the classes requiring the most uniformly sized grains is sand blast sand.Sand Blast SandThe use of the sand blast has increased rapidly during the past few years. It was formerly used almost entirely in the foundry to clean and remove inequalities from rough castings. This is still the most important application, but in addition, it is now employed for the removal of paint from old surfaces, carving and engraving on stone and marble, glass cutting, cleaning or renovating the rails of stone and brick buildings that have become discolored, preparing the surface of metals for the electrolytic bath, putting the final finish to metal surfaces, and has even been proposed as a means of channeling or cutting out blocks of stone in the quarry."

Jun 1, 1924

By G. R. Hopkins

A recently completed survey , made by the Bureau of Mines to determine the trend of fuel consumption at refineries in the United States , showed the following outstanding points : A decrease in the use of oil for fuel in 1927 of over 5,000,000 barrels as compared with 1926 ; a decrease in the use of coal of over : 1,000,000 short tons ; small increases in the use of both natural gas and refinery gas ; an increase in the use of petroleum coke . The decrease in fuel - oil consumption was approximately 2,000,000 barrels each in the Atlantic Coast , Texas , and Louisiana- Arkansas districts , with an increase of 1,000,000 barrels in the Indiana - Illinois district , or a net decrease of 5,000,000 barrels . The decrease in fuel- oil consumption by refineries in the Texas and Louisiana- Arkansas areas was offset largely by increased consumption of natural gas and refinery gas , whereas the increased consumption in the Indiana- Illinois region was more than offset by the decrease in coal consumption . The use of coal for fuel declined from 6,052,000 short tons in 1926 to 5,031,000 short tons in 1927. Practically all of this decrease was recorded in the Appalachian and Indiana- Illinois districts , which at the same time showed the largest percentage increase in the use of oil for fuel . It is probable , therefore , that although coal prices also fell off , a considerable quantity of oil replaced coal in this area in 1927. In addition , the group of refineries , which are by location more or less definitely committed to the use of coal for fuel , undoubtedly succeeded in saving a material amount of coal through the use of more efficient fueling methods . A total of 130,815,000,000 cubic feet of natural gas was consumed for fuel at refineries in 1927. This represents an increase of 8 per cent over the 1926 total . Nearly all of this increase resulted from the opening of a line from the Monroe field to Baton Rouge , La . Had this line not been opened , there would have been a decrease in the use of natural gas , as a number of districts , particularly the Rocky Mountain , reported decreases in its use . The use of refinery or still gases for fuel did not change materially during 1927 , there being a total of 52,807,000,000 cubic feet burned as compared with 52,077,000,000 cubic feet in 1926. Refinery gases are largely a product of cracking and , it was probably more than a coincidence that a few districts in which cracking slowed down in 1927 also reported less refinery gas used as fuel .

Jun 1, 1924

By J. W. Horne, W. L. Finley, A. D. Bauer, D. W. Gould

"The Bureau of Mines and the State of Colorado are cooperating in an investigation of the oil shales of Colorado. in this report the yields and the results of analyses of the oil and, gas produced from a number of oil-shale samples from the principal deposits of Colorado and other oil-shale States, are compared with samples from Scotland and Australia, where the oil-shale industry has had its greatest commercial development, and also with a sample from Brazil *here extensive oil-shale deposits are found shale samples were not selected as being representative of the different deposits, but they illustrate the wide variation in the nature of the organic matter of different oil shales.A further study is being made of the chemical composition of the shale, distribution of nitrogen and sulphur. in the products, temperatures at which organic matter decomposes, and the results will be presented in subsequent Papers, With complete data available on the chemical composition of the shales, it may be possible to explain some of the differences in the nature of the products from the various shales,Most of the work described herein was done under the supervision of M. J. Gavin. L. C. Karrick, formerly of .the Boulder laboratory, assisted in the work and gave many valuable suggestions."

May 1, 1924

By George S. Rice, J. W. Paull, R. R. Sayers

"Standard rock dust for use in the rock dusting of coal mines might be defined tentatively as powdered mineral, light colored and free of carbonaceous matter and free silica, all of which will pass a 20-mesh screen while 50% of it will pass-through a 200-mesh screen.Such dust may be prepared from limestone, gypsum, anhydrite, or shale free of sand and flint. For the initial rock dusting of the average nongaseous bituminous mines enough standard rock dust should be applied so that the combustible content of the resulting mixture of rook dust with mine dust shall not exceed 45%, a range somewhere between 35% end 45% being the practical objective sought.All entries, slopes or passageways and room necks should be rock dusted.Additional safeguards are:a.,Rockdusting roomsb.,Scattering of dust in vicinity of shots before firing.c.,Placing of barriers in the mouths of panels, cross-entries and other key positions.Redusting becomes necessary whenever the combustible content of the mine dust exceeds the permissible maximum. This should be determined by regular, systematic sampling, followed by a simple analysis of the samples for combustible content. A Bureau of Mines volumeter for measuring the density can be used for the determination of combustible content."

May 1, 1924

By T. L. Joseph

"In the January 3 issue of Iron Trade Review, Sweetser2, in referring to the problem of coke combustibility, points out that, ""Someone should formulate a rule for the rate of flow of coke through the zone of coke combustion that now appears to be confined to a comparatively restricted volume in front of the tuyeres,"" In formulating such a rule it is necessary to distinguish clearly between combustibility, a property of the fuel, and rate of combustion, which is determined by the rate at which air is supplied to the fuel bed. The rate of carbon gasified at the tuyeres of a blast furnace is independent of coke combusti-bility. A fast-burning coke will burn in a more restricted volume than a slow-burning coke, but both types of fuel will be consumed at rates determined by the supply of oxygen,A number of the definitions of combustibility that have appeared in technical literature relate more closely to rate of combustion than to combustibility. Perrott and Kinney) have correctly defined it as follows: ""Combustibility of coke from the standpoint of its use in, the blast furnace is inversely proportional to the mean rate of gasification per unit volume of the combustion zone, assuming other factors remain constant,"" Combustibility of coke refers therefore to those properties that determine the size or extent of the combustion zone. Relative differences in these properties can be measured by the depth of the fuel bed required to convert oxygen from the air into carbon monoxide."

May 1, 1924

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By J. F. Barkley

 This paper describes the method used and results obtained in testing a hand-fired down-draft furnace at a plant in Washington, D. C., in order to determine the method of firing that would give the best results with a minimu of smoke. The smoke regulations of the District of Columbia are very rigid, and are well enforced, A paragraph of the ordinance relating to furnaces other than household, reads, "The emission of dense or thick black or gray smoke or cinders from any smokestack or chimney 113ed in connection with any stationary engine, steam boiler, or furnace of any description within the District of Columbia shall be deemed, and is hereby declared, to be a public nuisance". This ordinance, if literally enforced, would eliminate all ordinary hand-fired grates and furnace combinations where coal other then anthracite is used. However, in several Gov- ernment plants where hand-firing of coal is still necessary conditions have been satisfactorily met by installing the down-draft type of furnace. In these plants, as at all hand-fired plants, considerable difference in operating details and methods is found. The firemen are paid day laborer's wages and are often inexperienced. The instructions of the furnace makers fre- quently do not appeal to the firemen, and are not closely followed, This is partly due to the necessity of running the boilers continuously at much higher ratings than were intended by the manufacturer. Tests were made on a Hawley furnace of this type to improve the methods of firing, particularly at the higher ratings.

May 1, 1924

By J. J. Jakosky

"This report is the second of a series dealing with electrical methods of underground communication nd signalling, and is a discussion of some of the factors involved in -applying radio in mines.A previous report2 described the results obtained by the use of the ""T.P.S."" of ground-conduction method of signalling, and outlined in a general way the requirements for a practical mine communication apparatus.The popularity of radio, the development work on new apparatus, a desire to render humanitarian service to entombed miners, and an endeavor to find new uses and applications for radio stimulated many persons to attempt the application of radio to mine rescue purposes. A number of experiments on underground reception from surface broadcast stations have been conducted by different experimenters in various parts of the country and the widespread interest in the subject is shown by the fact that these tests have been con¬ducted in many States, The Bureau of Mines has received information regarding, underground tests in Illinois, Pennsylvania, Arizona, Utah, Idaho, Colorado, Michigan, Wyoming, Kentucky, New York, Connecticut, and in England, Germany, Italy, and Franc.From occasional press notices and illustrations in different papers it may appear that radio communication in mines and in tunnels being excavated is en established fact, and that the method is comparatively simple. As a matter of fact the reverse is the case."

Apr 1, 1924

By P. Yant, A. C. Fieldner

"IntroductionIn its investigations relative to reducing the hazards of carbon monoxide poisoning, the Bureau of Mines recently had its attention drawn to a compound2a sold under a trade name for which claims are reported to have been made regarding its efficacy in reducing that type of poisoning in automobile garages. Accordingly, some of the product was obtained and analyzed for its power to absorb, oxidize, or destroy carbon monoxide; and the results are herein reported.Description of ""Compound"" (quoted from manufacturer's circular)While the circular does not actually state that the ""compound"" protects against carbon monoxide, the inference is therein, because each of the two following quotations is below these respective headings; ""Carbon-Monoxide Poisoning,"" and ""Chronic Gassing Among Garage Workers.""The ""compound"" holds chlorine and oxygen gases in solution with formaldehyde, which unites with the hydrogen to form hydrochloric acid., giving an over-supply of oxygen which burns up carbon just as a piece of wood is burned in the fire. The formaldehyde in the composition of the ""compound"" is a great affinity for ammonia and hydrogen sulphide."

Apr 1, 1924

By M. M. Myers

"Importance pf the small stone problem.Profitable disposal of limestone too small for making lime in the shaft kiln, is one of the most urgent problems in the lime industry. Reports received by the Bureau of Mines from 31 quarries show that the proportion of small stone varies from 2 to 40 per cent, averaging 18 per cent of gross pro¬duction, Modern methods of heavy blasting, and the use of crushers in large quarries tend to increase the proportion of small stone above that produced in early days when light blasting and hand sledging were almost universally used. There is also a growing movement toward underground operation of lime deposits, a method which in general produces a greater proportion of fines than is encountered in open-pit work. Thus the small stone problem is of growing importance, and demands the attention of every progressive lime producer. As the problem is of almost universal interest, it is urgently desired that every operator who reads this report will contribute from his knowledge or experience, answers to the questions on the final sheet.There are several markets in which small stone may be sold but in these markets the competition is generally keen and the prices low. The lime producer's chief product is lime, he understands its manufacture and marketing, and brings him a greater return than can be obtained from most limestone by-products. For these reasons it is evident that the conversion of small into lime is the nest desirable means of disposal."

Apr 1, 1924

By R. R. Sayars

"Carbon monoxide is a gas slightly lighter than air, with which it diffuses readily to make a homogeneous mixture. It will burn and has a wide explosive range, that is, an explosion is possible when the air contains from 15 to 73 per cent of the gas3. This explosive range is about the same as that for hydrogen and over nine times As Tide as that for marsh gas (methane). Like air, it has neither color nor taste and has no odor in concentrations usually encountered, therefore it cannot be detected by the ordinary senses with which men are endowed. It is produced by burning carbon containing fuels, no coal, wood, gasoline, etc., whenever not enough air or oxygen is supplied to burn and oxidize the fuel completely.The human race has probably been exposed to this gas since men first began using fires in confined or sheltered places. The poisoning as usually encountered is an acute condition resulting from breathing atmospheres con¬taining this gas. A number of eases described in the ancient literature Indicate that carbon monoxide was a frequent cause of death by accident, suicide and is a means of punishment or torture. A quotation by Lewin from Aristotle who lived in 384-322 B.C., states that ""animals collapse from harmful odors as men gets a severe headache and often dies through charcoal vapors"". The Roman knew that smoke was poisonous, and used the greenest most smoke-producing wood to put persons to death. The occurrence of carbon monoxide increased in frequency through the years until at the present time it is found in the home as well as in many industries. The following table gives the approximate percentage of carbon monoxide found in gases from various sources of poisoning.4"

Apr 1, 1924

By H. W. Gillett, E. L. Mack

"This report describes the trend of developments in electric brass-furnace practice in the last two years, and supplements Bureau of Mines Bulletin 202, ""Electric Brass-Furnace Practice"", which was published in 1922. In that bulletin it -as pointed out that some of the lines on which electric brass-furnace progress would take place were clear, but others were less so.Developments in foreign countries.Foreign brass-melters have not yet adopted electric melting to an extent comparable to its use in the United States. It is doubtful Whether all foreign countries combined use 100 electric brass furnaces; of these about 35 are of American make (Ajax, Detroit, Baily) and are operating in Canada, Mexico, England, France, Japan, Sweden, Switzerland, Spain, Norway, Germany, Argentina and Czecho-Slovakia.`The Rennerfelt furnace finds some use in Sweden (1)c, notwithstanding its high metal loss on alloys high in zinc, Two German firms are reported(2) to be using the Rochling-Rodenhauser induction furnace on bronze, the average energy consumption being given as 400 kw.-h. per ton. No comment is made on any trouble from the ""pinch effect"", A firm in Switzerland is reported (3) to use three 600-lb., direct-arc furnaces of its own design to melt babbitt, antimonial lead, coinage silver, nickel, copper, and brass. The metal loss on yellow-brass turnings is high. Use Of a direct-arc furnace in England, with precautions aimed to prevent surface overheating, vas abandoned (4) in favor of an Ajax furnace."

Apr 1, 1924

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By Oliver Bowles

"Underground operation.In its broader sense the term ""mining"" is applied to all processes whereby raw materials are taken from the earth to be used as sources of mineral products. In a more restricted sense ""mining"" is applied to underground operations as contrasted with open pit work designated as quarrying. The tern is used in the restricted tense in this paper; for it relates to the exploitation of limestone deposits by modern methods of underground operation rather than by open pit methods.Present tendency toward miningIt may seem to some readers that a paper on mining limestone will find little general interest among lime plant operators, for only a limited number of them have yet resorted to this means of procuring raw materials. It is noteworthy, however, that a growing tendency exists toward underground operation, for one by one quarry owners are faced with increasing difficulties in open pit operation. It seems desirable, therefore, for operators to keep closely in touch with this gradual change in process, to inquire into the underlying causes, to compare costs, and to study the effects of the change in method on subsequent steps in calcining the stone to produce lime."

Mar 1, 1924