Search Documents

By A. W. Fahrenwald

The function of the c1assifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred to as "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particu1ar method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted. Relation of Classifier Efficiency to Grinding Efficiency The energy of crushing, and therefore the cost, according to Rittinger's Law,l is proportional to the new surface exposed in crushing. Since the new surface produced in crushing is nearly proportional to the reciprocals of the diameters crushed to, it is obvious that the cost of crushing in the finer sizes is tremendously greater than in the coarser sizes for equal ratios of reduction. High circulating load of finished sand in the circuit of the classifier and grinding mill is therefore obviously expensive practice. It is the classifier's function to reduce this to a miniMum.

Jan 1, 1930

By R. S. Archer

THE binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.1 Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application.

Jan 1, 1930

By W. E. Mitchell

The ore that is being treated by the present plant lies between the leached zone, or capping, and the mixed sulfide and oxide zone. The principal copper minerals are chalcanthite (CuS04.5H20), brochantite (CuSO4.3Cu (OH)2 and atacamite, (CuC12.3Cu (OH)2). There are, in addition, some other minerals such as cuprite and kröhnkite (CuS04. Na2S04.2H20). These minerals, with many others, occur in a greatly crushed granodiorite rock. most of the copper-bearing minerals occur in the cracks and veinlets, but there are disseminated values and it is probably the relative proportion of these that accounts for some otherwise unexplainable variations in extraction. The entire mineralization of the ore is complex and varies with depth. This variation, the problems presented thereby, and the effect of various constituents of the ore will be taken up in detail. An analysis of :in unweighted composite of the ore treated during 1927 follows: I'Lr Cent. Per Cent. Per Cent. Cu............... 1.58 S................. 2.10 Mo............ 0.01 SiO? ............. 66.10 HNO3 ........0.03 As............ 0.005 Fe.......... 1.41 C1 .............. 0.05 Sb............. 0.005 CnO ..... 0.20 Na................ 0.80 Ba............ 0.01 A1203 .......... 17.70 KI.............. 4.80 H20............ 0.70 mgO.............. 0.68 Mn............... 0.07 0 in sulfates. . . . 3.94 Total..... 100.19 The most important constituents of the ore, as indicated by experience to date, are: (1) The total copper content; (2) the acid-insoluble copper; (3) the acid-making copper mineral, mainly the chalcanthite; (4) the chlorine; (5) the nitrates; (6) the soluble iron; (7) the soluble molybdenum. The total copper content needs no discussion. In Table 1, the values are weighted averages calculated from individual charge analyses. The acid-insoluble copper directly affects the extraction, as the present leach recovers practically no acid-insoluble copper. In Table 1 the values are unweighted averages of the analyses of monthly composite samples. The acid-making copper mineral affects the amount of copper that can be dissolved from the ore without neutralizing acid in the solution. The

Jan 1, 1930

By E. A. Hewitt

This paper describing the mining practices at the Park Utah mine in the Park City district is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Park Utah mine is situated at Keetly, Utah, about 5 miles east of Park City. The Park City district lies on the eastern slope of the Wasatch Mountains, 25 miles southeast of Salt Lake City. The district embraces a tract located between the crest of the main range on the west and the mountain meadows along the eastern foothills. The elevation of the Union Pacific Railroad station at Park City is 7,000 feet above sea level. The town and mines are served by two railroads; one 28 miles long is a branch of the Union Pacific Railroad and connects with the main line at Echo Junction, east of Ogden; the other is 35 miles long and joins the Denver & Rio Grande Western Railroad at Salt Lake City. The district and mines are also accessible by excellent automobile roads from Salt Lake City and surrounding points (fig. 1).

Jan 1, 1930

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

By Alfred H. Bell, Paul F. Simpson

The year 1929 was one of continued activity in the petroleum industry of Indiana and Illinois but the new production obtained has not been sufficient to offset the decline in the production of the old wells. (Table 1). Drilling costs have not changed materially during the year and the prices of crude oil have increased slightly so that the prospects for further testing are good. The total number of completions in Illinois in 1929 (Table 2) was greater than for any year since 1917. More than half of these were in the Dupo field, St. Clair County, and the development of this field was largely responsible for the increased ratio of producers to dry holes in the state as a whole. In the southeastern Illinois field which has produced about 97 per cent. of the state's petroleum the number of completions was greater than in 1928 and the percentage of producers was a little higher. Although a number of scattered wildcat tests were drilled most of them were not located on favorable structure and the only noteworthy discovery was that of a shale-gas horizon at shallow depth in Morgan County in western Illinois where gas has been produced for a number of years from sandstone and limestone. In Indiana the number of completions (Table 2) was only slightly less than in 1928. Most of the new wells were drilled in the southwestern part of the state, which now produces more than 90 per cent. of Indiana's petroleum.

Jan 1, 1930

By F. L. Wolf

THE catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This' means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a, preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of, materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though its importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation.

Jan 1, 1930

By M. R. Campbell

You have just heard several papers on the classification of coal as this subject appears to the chemist; I shall approach it from the point of view of the geologist who, perforce, has to deal with coal as it occurs in the ground and with the miner of coal who knows certain phases of the physical characteristics of coal better than the scientist can possibly know them. The chemist is familiar with coal as it reaches him in the laboratory, but he seldom has an opportunity to see it in its native condition and to study its physical characteristics and its behavior under varying conditions of weather, transportation and use. He naturally regards the chemical composition of coal as the all-important feature upon which to base a system of classification and he is sometimes inclined to ignore as unscientific any scheme of classification that is based on characteristics other than chemical. The geologist, on the other hand, although he is glad to use the data furnished by the chemist, must depend largely upon the differences that he can see and feel. Classification Understandable to the Layman In the very comprehensive program of examination of the coal fields of the West which the U. S. Geological Survey undertook in 1906, it fell to my lot, as the responsible head of the work, to classify the coals in advance of much knowledge of their chemical composition and in regions where mining had not begun. In this work I was forced to devise some sort of classification that would work practically and that would be understandable to the layman in the field. Much of the classification was based on the work of those who had gone before me, but in the low rank coals of the West the field was unoccupied and I was forced to devise a scheme embracing both chemical and physical characteristics. This scheme has stood the test of actual practical application for several years but it needs revision and the sharpening of the limits between the different ranks. I feel that my experience warrants my saying that physical characteristics must be considered and I have faith to believe that some scheme embodying both can be devised.

Jan 1, 1930

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

By R. J. Henry

This paper describing the mining practices at the Teck-Hughes mines at Kirkland Lake, Ontario, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in various mining districts. HISTORY Prospecting was begun in the neighborhood of Kirkland Lake in 1906, but staking did not take place until 1911. Gold-bearing veins were discovered by surface trenching in 1913 on the mining claims which now make up the Teck-Hughes Gold Mines (Ltd.). A small mill was erected in 1916 after the completion of some underground exploration. A transmission' line was built in 1917 to the camp to provide adequate power for a vigorous underground campaign. Also in 1917 the present management took control operations since 1916 have been continuous,' with a steady increase in production to date.

Jan 1, 1930

By F. D. DeVaney

In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley Experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Linn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Joseph and Kinney in writing about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say: "***It has been estimated that 26 to 35 million tons of ore contain 5 to 35 per cent of manganese, and the total domestic tonnage is from 75 to 48 million tons. The mean of these values is 30.5 million and 42 million tons, so it is seen that about 75 per cent of the reserves are in Minnesota." The manganese-bearing ores of the Cuyuna district maybe roughly grouped into two classes. The most abundant ore is of the low-silica, low-manganese, and high-phosphorus type called brown are. The other type is the so-called black ore, which is characterized by a higher manganese and silica content and by a lowe phosphorus analysis than the brown ore. As a general rule the brown ore carries less than 10 per cent of manganese while the black ore contains about 15 per cent and sometimes as high as 22 per cent of manganese.

Jan 1, 1930

By T. D. Thomas

In this paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first. Misfires Caused by Faulty Detonators The important part of an electric blasting cap, to the user where multiple shot-firing is done, as in the steep-pitch, thiek-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire. The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also by a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented. The officials at the mines had to determine the various causes of misfires and have them corrected. The rock contractors who use large quantities of 60 to 80 per cent. explosives and do all firing electrically were thoroughly instructed as to the proper methods of doing their work, and closer supervision was given to their work. The manufacturer's representatives stressed the importance of the use of galvanometers; accordingly these were purchased and used. Larger firing lines were installed under the supervision of a demonstrator of the company manufacturing the caps and explosives. However, misfires again occurred and it was evident that the source of the trouble was not wholly

Jan 1, 1930

By Charles R. Fettke

The outstanding event of the year 1929 in the Appalachian area was the intensive drilling activity in the Bradford and Richburg pools of northwestern Pennsylvania and southwestern New York State, particularly the former, in connection with the continued extension of the five-spot system of water-flooding. More new development work was undertaken and completed than during any previous year since reclamation methods were first applied. This was due in part to an excellent price for oil and in part to discovery of the fact that more intensive methods (five-spotting) yielded greater profit. While several oil wells of comparatively large initial production were completed, no new oil pools of significance were discovered in the Appalachian area during the year. A number of small gas pools were opened in areas already surrounded by producing wells and at least three others in areas located some distance from any producing pools. Petroleum Development According to statistics of the U. S. Bureau of Mines, 33,7,57,000 bbl. of petroleum were produced in the Appalachian field during 1929 as compared to 31,060,000 bbl. in 1928.' Of the total 1929 production, 23,391,618 bbl. consisted of Pennsylvania grade oil as compared to 21,096,710 bbl. in 1928. The 1929 Pennsylvania grade production represents an increase of 37.4 per cent. over that of 1924. This increase can be attributed largely to the rapid development of water-flooding in the Bradford and Richburg pools. The Bradford field of northwestern Pennsylvania and adjaccnt portions of New York State experienced the busiest year since the boom days of the early eighties. Wells completed during the year totaled 2679.2 In spite of the high prices asked for acreagc, which in some of the choicest territory has been as high as $6000 an acre, a considerable number of properties changed ownership during the year. There is at present a pronounced tendency to consolidate the great number of small individually operated properties into larger units.

Jan 1, 1930

By Wilson B. Emery

The Hidden Dome gas field, situated in Washakie County, Wyoming, was discovered Sept. 26, 1917. Subsequently five additional gas wells were completed and a large reserve was developed. For a number of years this field completely supplied the domestic market at Basin and Greybull, as well as the refinery at the latter town, and it is still supplying gas in small amounts to this market. Production is obtained from the sands of the Frontier formation at depths ranging from 1000 to 1500 ft. The original rock pressure was 725 Ib. and initial production ranged from 4,000,000 to 28,000,000 cu. ft. per day per well. Porosity of the sand, determined from the size of the productive area and the amount of gas recovered, is over 18 per cent. Area and Management It is estimated that the productive area is about 640 acres. Its outline is indicated on Fig. 5, on which are also shown the locations of holes drilled on the structure and the area of unit operation. The unit area is owned by the Ohio Oil Co. and development and operation have been by this company. No productive well has been completed outside this area. The entire area was Government land filed on under the placer mining law. Results of Unit Operation With six producing wells, or an average of one to each 160 acres, the pool is completely developed. Location of the wells was made with respect to structural conditions plus the requirement that at least one well be drilled on each 160-acre placer claim. Perhaps a somewhat more uniform spacing of the wells might have been accomplished and one well eliminated, but it must be borne in mind that the holes, on account of their shallow depth, were not expensive and that the object was to develop as reliable a reserve as possible. There is no cause to suspect that these holes have not adequately drained the reservoir and there is every reason to think that any additional wells, which might have been drilled under diversified ownership and operation, would have been an economic waste. Unit operation by a competent company has not only resulted in the elimination of loss of gas through careless development and operation

Jan 1, 1930

Jan 1, 1930

By L. H. Dushak

DURING the war period of quicksilver activity there were a number of departures from what may be termed the classical quicksilver metallurgy. Attempts were made to beneficiate low-grade ores by gravity concentration and flotation; mechanical furnaces began to replace the Scott furnace and the vertical coarse-ore furnaces, and condensers of sewer tile and redwood tanks were used in place of the older brick and stone condensing chambers. Other developments that have occurred during the current period of quicksilver activity are mainly in the nature of improvement and further refinement of those started during the war period. Each period of quicksilver activity has been accompanied by the proposal of various new processes, including wet methods for the treatment of quicksilver ores and innovations in furnaces, retorts and condenser equipment. As far as the author knows, nothing of economic significance in the way of "new processes" has been developed. There is in fact no real need for any essentially new process for the treatment of quicksilver ores; the direct furnace treatment is simple and inexpensive. Moreover, with rare exceptions, the quicksilver industry has no complex or refractory ore problems corresponding to those which are receiving more and more attention from metallurgists in other branches of the nonferrous field. Under these conditions improvements in quicksilver metallurgy must be looked for through the adaptation of current developments in engineering and metallurgy generally to the particular needs of quicksilver practice rather than through the invention of new processes.

Jan 1, 1930

By L. H. de Wald, J. Walter Scott

The removal of lead by fire refining methods from copper of electrolytic quality is growing in importance. Particularly is this true of the refining of secondary copper and copper cathodes obtained from electrolytic cells where lead is used as the anode material, as in the electrolysis of ore-leaching solutions and foul electrolyte. When investigating the removal of small amounts of lead from molten copper in a reverberatory furnace during the refining of secondary copper of otherwise electrolytic copper quality,' it was found necessary first to know something about the distribution of the lead throughout the bath. The authors believe that it is not generally known how small amounts of lead as an impurity are distributed in a molten copper bath; that is, whether the lead is concentrated at the bottom or at the top, or whether it occurs more or less uniformly throughout the bath. The data contained in this report may help, therefore, in the development of a satisfactory fire refining method for the removal of this obstinate element from a molten copper bath. The first step was the development of a method for taking samples from various locations in the bath, at the surface and at various depths. The sampling device used, shown in Fig. 1, consisted of a 10-gram fireclay assay crucible fitted into a ring on the end of a steel rod handle of suitable length. A fireclay scorifier, 2 in. dia., with a ½-in. hole bored in the

Jan 1, 1930

The United States Bureau of Mines frequently receives requests for information regarding the details of its organization and the nature of its activities. In response to such an inquiry a series of articles outlining the work of the bureau as a whole and of its different divisions was prepared and published in the United States Daily, Washington, D. C., during November, 1929. These articles are reprinted here in the hone that they may assist in giving the public a more complete understanding of the aims and purposes of the bureau and the methods by which it is laboring for the attainment of safer conditions and more efficient methods in American mineral industries. An index of these articles, with the dates of 'their publication in the United States Daily, is given below.

Jan 1, 1930

R. F. McELVENNY.- Mr. Oldright has just given me a letter to read to you, which I think it may be of interest. It is headed, "Silver Meeting Dinner". The letter is as follows: "To Members of the A. I. M. & M E.: The annual business meeting and election of officers will take place at the University Club, Wednesday, May 28th, 1930 at 7 p.m., at the Silver Meeting Dinner. The Nominating. Committee for next year's officers have proposed the following names: Chairman, Robert Wallace; Vice-Chairman, G. W. Crane; secretary, C. T. Van Winkle, Other nominations can be made at the meeting. Utah being the leading silver producer of the United States, constructive suggestions regarding the silver situation will be made at this meeting which are new and of general interest to the members. The speak¬ers will be followed by a Round Table discussion of the silver situation and proposed remedies. Speakers will be - W. M. Ferry, President of the Silver Producers' Association, 'Recent developments in the Silver Question'.. Senator Frank J. Cannon, 'The Cannon Plan'. George W. Snyder, 'The Manufacture of Sterling Silver.' Discussion by J. J. Beason, G. W. Crane, J. 0. Elton, J. W. Wade and others. Members of the Conference on Copper Reverberatory Smelting are invited to be present. Chairman J. A. Norden will preside. C. T. Van Winkle, Secretary. Dinner will be $1.50 per plate." The next subject is "Boilers: Proper construction of, so as to secure best utilization of heat from gases, and facility in removing dust and clinker with minimum losses in operation." Who is particularly interested in that subject? The type of boilers is practically a standard practice now. I do not know of anybody that is using the tandem system now. No one is building a plant with a tandem system in it.

Jan 1, 1930

By F. H. Labee

Questionnaires and special letters soliciting information were sent to a great many geologists, petroleum engineers, independent operators, and representatives of large companies in Arkansas, Louisiana, Texas and New Mexico. Replies to more than 50 per cent. of these letters were received. A survey of the facts and opinions presented in this correspondence will be made a little later, but first some of the general aspects of the problem will be reviewed. By "unit operation,"1 we mean the development and operation of a single entire pool, or reservoir, of petroleum by one management, on a systematic and scientific plan which is best calculated ultimately to extract from the pay sand and bring to the surface of the ground the largest possible amount of oil with the greatest possible total profit. No one, as far as the author has been able to ascertain, denies the advantages, both scientific and practical, of unit operation. All are agreed that it is sound in theory. It permits the proper distribution of wells, which should always be spaced on the ground according to a regular geometric plan with the intention of maintaining the same spacing all the way down and into the pay sand, or pay sands. This spacing will be different for different fields, depending on such variable factors as the lithologic character of the pay formation, the nature of the controlling structure, the depth of drilling, the viscosity of the oil, and so on. From the viewpoint of engineering practice, as applied to economical extraction of oil, there is no more important consideration than well spacing—well spacing in the pay formation, and not merely on the surface of the ground —for the method of well spacing has a direct bearing upon all such engineering practices as pressure control, repressuring by gas, the water drive, and SO on. H. C. Miller2 summarized the advantages of an ideal cooperative development plan as follows: "Among the more important advantages of

Jan 1, 1930