Search Documents

By Ionel I. Gardescu

During the summer of 1930 the average daily oil production of Rumania registered a new peak at 128,000 bbl. per day. The estimated potential production as of September, 1930, was as high as 235,000 bbl. per day. During the latter part of the year, by mutual agreement, the operators decided to curtail their output to about 100,000 bbl., which brought the average for the year to 116,600 bbl. The total production for 1930 was 41,572,000 bbl. (last month estimated) as compared with 35,757,000 bbl. for 1929, or an increase of 16.3 per cent. over last year's production. The production for the last 10 years is given in Table 1. The curtailment of production was prorated per company, based on its total estimated potential production as of September, 1930, and not per field. As a consequence, at present there is little development of protected or slightly productive areas; viz., Arbanasi, with an average production of 1750 bbl. per day, dropped to less than one-third after curtailment came into effect. Moreni, with an average production of 92,000 bbl. per day, while producing 58 per cent. of the country's total output in 1929, went to 67 per cent. at the beginning of 1930 and to 75.2 per cent, towards the end of the year. The modified Mining Law of 1929 is still in effect. This law withdraws the restrictions set on foreign capital by the law of 1924. As a consequence a large percentage of proven state land was alloted through competitive bidding to foreign companies. The Romano-Americana (Standard of New Jersey) acquired several leases in the Boldesti and

Jan 1, 1931

By Chu-Phay Yap

This is the first of a series of theoretical papers on the iron-carbon system. A simple critical analysis of the ordinary constitution diagram of the iron-carbon system yields valuable information regarding the nature of the equilibria in the liquid and solid states. It is shown, for example, that the solute in the melt is Fe3C, but in solid Fe (austenite) the solute is carbon. The thermodynamic laws of the depression in the freezing point of solid solutions have been developed and discussed. Using the usual method of plotting the logarithm value of the concentration of the solvent (in this case, the ratio of concentrations of the solvent in the liquid and solid phases) against 1/T, curves are obtained. A rigorous thermodynamic analysis of these curves has been shown to yield considerable information regarding the internal equilibria of the system, with which the phase rule does not deal altogether. In this way, it is shown again that the solute in the melt is Fe3C, but in the solid rFe the solute is carbon. Various heats of reaction (fusion and transition) and other thermal data have been derived: and discussed with a view to correlating the conflicting experimental data obtained by different investigators of the system.

Jan 1, 1931

By Robert Baker

IT has been demonstrated in the laboratory by A. J. Phillips1 that a transformation or conversion from beta directly to alpha may take place in a brass of 61 to 62.5 per cent copper content. The completion of the transformation is dependent on a rapid rate of cooling from the all-beta field through the alpha + beta range to the alpha field. Phillips states that in a slowly cooled alloy containing 62 per cent copper and 38 per cent zinc the copper content of the beta is progressively decreased from 62 to 56 per cent by precipitation of alpha. Rapid cooling tends to prevent the separation of alpha with a copper content of more than 62 per cent by reducing to a minimum the time required for passing through the alpha + beta range. Upon crossing beyond the (alpha + beta.)/(alpha) boundary to the all-alpha region below, the material is transformed from beta to alpha. It is essential that there be no change in composition. Phillips obtained his results by quenching a 62:38 copper-zinc alloy from 850° C. in iced brine at -8° C. No reference to the occurrence of this transformation in a manufacturing process has been found in the literature. An investigation of the microstructures of a number of hot forgings made from leaded brass rods yielded one forging in which this striking conversion from beta to alpha had occurred. The purpose of this paper is to describe the transformation and certain conditions under which it may occur during the hot pressing of brass. The conversion was noted in a shape forged from a leaded brass rod, the composition of which was: Cu, 60.26 per cent; Zn, 37.86; Pb, 1.88. In this study the lead content was disregarded and the alloy was considered to be equivalent to an alloy of 61.40 per cent copper and 38.60 per cent zinc (98.12 parts = 100 parts). The possibility that the lead might obstruct or accelerate the precipitation of alpha was not studied. The lead appears as black globules in the photomicrographs and has a negligible solubility in the alloy.

Jan 1, 1931

Separates of all the Technical Publications published in 1931 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions. Copies of these papers have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Additional copies are sold at the rate of I cent per page; minimum charge, 25 cents. Metal Mining Tech-nical Publi- Title Author Meeting TRanb. cation Volume No. and Page* 411-A.43 Ventilation at the Portovelo Mines, J. P. Harmon New York. T31, 83 Ecuador (18) Feb., 1931 425-A.44 Use of Models for the Study of Mining P. B. Bucky New York, Problems (28) Feb., 1931 Milling and Concentration 375-B.32 Ball Mill Studies, I (53) A. W. Fahrenwald New York, H. E. Lee Feb.. 1931 401-B.33 Experimental Flotation of Oxidized H. S. Gieser New York. Silver Ores (9) Feb., 1931 410-B.34 Flotation of Minor Gold in Large-scale E. S. Leaver New York, Copper Concentrators (32) J. A. Woolf Feb., 1931 414-B.35 Effect of Particle Size on Flotation A. M. Gaudin New York, (23) J. 0. Groh Feb., 1931 H. B. Henderson 416-B.36 Ball Mill Studies, 11.—Thermal A. W. Fahrenwald New York. Determinations of Ball Mill Effi- G. W. Hammar Feb., 1931 ciency (13) H. E. Lee W. W. Staley Iron and Steel Division 38QC.59 Open-hearth Steel Process as a Prob- E. R. Jette New York, C31, 80, 111 Iem in Chemical Kinetics (34) Feb., 1931 381-C.60 Thermodynamic Study of the Phasial Yap, Chu-Phay New York. Equi1ibriain the System Iron-car- Feb., 1931 bon (26) 382-(3.61 Influence of Dissolved Carbide on the Yap, Chu-Phay New York, Equilibria of the System Iron-car- Feb., 1931 ban (19) 383-C.62 Research on Blast-furnace Slags. R. S. McCaffery New York, Three papers (88) Co-workers Feb., 1931 384-C.63 Statistical Analysis of Blast-furnace K. S. McCaffery New York, C31, 60, 70 Data (13) R. G. Stephenson Feb., 1931

Jan 1, 1931

By H. H. Power, C. H. Pishny

When an oil operator becomes a party to a proration agreement he may wonder, with good cause, whether production prorated .today is merely deferred until tomorrow or whether oil might be lost. Various types of evidence obtained from production records when studied quantitatively are of great assistance in arriving at definite conclusions. A study of individual examples cited in this paper leads towards some solution of the problem, particularly when they are considered in the aggregate. Many production curves on various pay horizons were studied. A disappointingly large number of these were of contributory value, but inconclusive. However, there were enough curves of similar type from the Wilcox sand at Earlsboro, Bowlegs, Seminole City, the Cromwell horizon at Little River, and the Simpson dolomite at Valley Center, Kansas, from which reasonably definite conclusions were drawn. Assuming that deferred production is later made up with no increase in ultimate recovery, a curve (Fig. 1) shows the normal flowing and pumping life of a composite well, contructed by the family curve method. The initial production of the well shown is 1700 bbl. daily and the allowed production is 25 per cent. On this basis the average daily allowed rate for the first month is 425 bb1., or the area BCDE, which is equivalent to the area AFDG under the normal decline curve. The potential production for the second month is 1500 bbl. and the allowed production 375 bbl. daily. By this procedure a potential curve for each succeeding month is obtained (points A, H, I, J and K). If the well is opened it should produce somewhere near its potential curve for a short period and then decline at a more rapid rate than the potential curve. This theoretical analysis is basic. Actual examples exhibiting all points raised by the ideal curve are rare. Proration in the Mid-Continent area has been effected mostly by leases rather than by individual wells; hence a well may produce any

Jan 1, 1931

By F. Keller, E. H. Dix

The desirable high strength and hardness of the heat-treated strong aluminum alloys result from two distinct structural changes: (1) the formation of a solid, solution by heating at the required temperature for a sufficient period, and the substantial retention of this solid solution by rapidly quenching; (2) precipitation of particles of constituent and coalescence to a critical size to produce maximum strength and hardness. In alloys of the duralumin type, that is, alloys containing both copper and magnesium silicide precipitation takes place at normal atmospheric temperature, whereas in alloys containing copper without magnesium silicide or magnesium silicide without copper, maximum properties are obtained only after an accelerated aging treatment consisting of heating for 15 to 20 hr. at temperatures of about 150" C. The mechanical properties of these alloys subsequent to quenching but prior to aging are ideal for forming operations. Unfortunately, however, the alloys of the duralumin type age very rapidly during the first 24 hr. and aging is substantially complete after four days. For severe forming, such as the heading of rivets, it is desirable that this be accomplished within ½ hr. or at the most 2 hr. after quenching. Alloys containing magnesium silicide without copper also age at normal temperatures but the aging is less rapid and the material can be satisfactorily worked within several weeks after quenching. Some slight aging of alloys containing copper alone also takes place at room temperature but it is unimportant from the standpoint of workability. Any method of retarding the aging at room temperature of the duralumin type of alloys would be of considerable advantage in that the period during which the material could be worked successfully would be lengthened. For instance, in aircraft plants it is customary to supply the workmen with small lots of rivets that should be used within ½ hr . after heat treatment. Such procedure has the obvious disadvantage of being uneconomical, and furthermore there is always the possibility that the workmen would use the rivets after the time limit had expired, or the supply being depleted might use some that had not been heat-

Jan 1, 1931

By T. L. Joseph

The size and accessibility of the Minnesota manganiferous iron ore deposits make them attractive as a potential source of erromanganese, which is essential in the production of steel. For several years the Bureau of Mines has been conducting experiments to determine the feasibility of producing ferromanganese from these ores by a three-step process which involves (1) the smelting of the ores in the blast furnaoe to produce a high-phosphorus spiegel; (2) the treatment of the spiegel produced from step 1 in an electric or open-hearth furnace to separate the manganese from the phosphorus and the iron; and 3) the smelting of the high-manganese slag from step 2 to produce forromanganese. The details of the first two steps of the process and the results of tests with the experimental furnaces Lave been given in previous reports.5 The m$ or part of the experimental work on the second step has been conducted in a half-ton open-hearth furnace. Some preliminary tests showed, however, that the electric furnace has some distinct advantages over the open hearth for producing, from high-phosphorus spiegel, a slag containing from 45 to 55 per cent manganese and phosphorus and iron in amounts required for ferro-grade ore. The electric furnace tests described in this paper were made to get more information as to the possibilities of the electric furnace in connection with this problem and to study the fluxing effect of alumina on high-manganese slags. Herty, Conley, and Royer have reported' results of laboratory tests which showed that slags containing from 60 to 75 per cent MnO, from 8 to 10 per cent S102, and small amounts of CaO MgO, and FeO, were sufficiently fluid at 1,450° to 1,550° C. to pour readily if 12 to 14 per cent alumina was present. With a normal A1203 content resulting from the A1203 in the

Jan 1, 1931

By Ray W. Arms

The combination wet and dry coal-cleaning process is not an attempt at a compromise between the wets and the drys nor is its merit confined entirely to the limitation of moisture in the smaller sizes. It is more correctly, and more broadly, an application of the sized-coal cleaning principle adapting itself in an ideal fashion to present day multiple-size preparation practice. The purpose of this paper, therefore, is to call attention to the broader significance of the term "combination wet and dry process" and to mention some of the factors that govern its application. In the narrow sense, when considered apart from the sized-coal cleaning principle, the combination process finds its justification chiefly in the ability to limit the moisture in cleaned coal. Larger sizes of coal offer less superficial area compared with their bulk for the attraction of moisture films. They drain more readily in bins or railroad cars, having more interstitial space for the free flow of water. Therefore, they neither attract nor hold objectionable moisture percentages. In fact, there is so keen a demand for certain washed sizes containing some moisture that hygroscopic salts such as calcium chloride are applied to attract and retain it. When coal deliveries are made on a guaranteed moisture percentage the coarser sizes may be washed and mixed back with the fines without adding greatly to the original moisture but the fines must be dry cleaned or dried to control moisture. Thus in all respects moisture in the coarser sizes is less objectionable than in the fines. The implication of this statement, that moisture is always more or less objectionable, is true. It is safe to say that if dry-cleaning apparatus could be perfected to a point at which its technical results, cost and other aspects would be equal to wet washing, water would no longer be used. As it is, we find that good technical results are more difficult to obtain by dry cleaning than by water. Obviously the use of air tables for coarse coal is not ideal, for it involves the attempt to stratify material in a thin bed on a table surface when the load is only one particle deep. Furthermore, the various air cleaning tables on large sizes require a large volume of air for separation, more power to operate, more dust-collecting apparatus and involve more coal breakage.

Jan 1, 1931

By C. P. Parsons

To properly account for the various characteristics of drilling muds obtained in different areas and geological horizons, it is necessary to study the composition of the mud from a chemical and physical standpoint as determined by the proportions and activities of the various solid contituents that are present in various states of division. Briefly summarized, science teaches that there are three states of division into which these solid constituents or particles may be grouped: namely, the suspended state, the individual particles of which are known as suspensoids; the colloidal state, in which the individual particles are termed colloids; and the crystalloidal state, wherein the individual particles are held in true solution and are termed crystalloids. The suspended state is one wherein the particles are fairly large and are present as molecular complexes, having none of the properties of colloids or crystalloids. Since matter varies in physical character and in chemical activities with its state of division, these coarser suspensoids do not themselves materially affect the physical or chemical properties of the solution in which they are suspended. On the other hand, they are distinctly detrimental in drilling muds and it is desirable that they be removed. Under the general classification of suspensoids are included sand, gravel and cuttings which contribute nothing to the colloidal stability or other desirable properties of the drilling fluid. As the state of division approaches but does not reach a molecular simplification, the term "colloidal state" is used in describing this condition. The colloidal state arises when one form of matter is in a very fine state of division and is distributed through a second phase. The material in the finely divided state is called the dispersed phase, while the liquid in which it is dispersed is called the dispersive phase. These particles of matter are in a colloidal state and will not settle out from the dispersive phase so long as colloidal conditions are stable. Moreover, they exhibit the property of having an oscillating movement around a central position in solution (the Brownian movement). In the third state of division, the crystalloidal state, the individual particles are held in true solution and are usually present as single molecules or ions. In a drilling fluid the water content of the fluid contains

Jan 1, 1931

By F. Lynwood Garrison

The future of the Witwatersrand depends upon the possibility of mining and milling profitably the large tonnage of relatively low-grade gold ores known to exist in that area. The problem must be solved if the existence of the gold-mining industry in South Africa is to be saved and continue. To show that this disaster may be avoided, or at least postponed for another decade or longer, the following official statement is of interest: "There is a fairly large area of possible orebody on the East Rand of whose value and depth from the surface we have some though not very accurate knowledge. There is a far larger area south of the Central Rand which probably carries much payable ore, but at depths that at present appear too great to mine. Finally, there is a narrow strip of country over 100 miles in length stretching south from the Rand to Klerksdorp and beyond, which may contain large ore-bodies. The Witwatersrand rocks outcrop over portions of this ground and in places conglomerates occur in it that carry small bodies of payable ore. There is reason to believe that conglomerates of the Witwatersrand system exist over all this strip, though they are for the most part covered by later sediments. It seems probable also that there are large blocks of payable reef in this belt, at any rate in the area that lies close to the present western limit of the developed mines. The structure in this neighborhood is however very complicated and to prove the orebodies will be both difficult and costly." Ores in the Witwatersrand It should be explained in this connection that the conglomerates mentioned here were originally old gravel beds now consolidated into bedded sedimentary rocks, very hard because strongly cemented with secondary silica. The gold exists in this cement and is rarely found in the pebbles composing the rock or bed called locally reef. It is important to realize that these gold deposits are beds; not veins as generally understood by mining engineers and geologists. In addition to these low-grade ore reserves we have also to consider the ore left behind in the old stopes of the upper levels near the surface,

Jan 1, 1931

By J. William Ganser

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically palled to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Fred Burkett, civil engineer, and F. O. Londrey, chief clerk, of the Trinity Portland Cement Co., for assistance in preparation of this paper, "The Geology of Dallas County. 1918," Bulletin 1818, Texas Geological Survey, Austin, Tex., by E. W. Shuler, was also freely consulted.

Jan 1, 1931

By Arthur Phillips, E. S. Bunn

During the past few years considerable interest has been shown in the study of fiber, and its effect, in wrought metals. Fiber has recently been defined as a "condition of parallelism of important lines or details in the structure."' Briefly stated, two distinct types of fiber are commonly encountered. One results from the alignment in the direction of working of constituents, more or less segregated, such as slag, oxides, carbides and dendritic formations. The second, and least understood, type is produced by working the metal below the recrystallization temperature in such a way as to develop a parallelism of the grains. This condition is readily recognized by the pronounced elongation of the grains in the direction of working. Under certain deformational treatments the grain fragments produced by cold working tend to orient in certain definite directions with respect to the axis of extension. Furthermore, even in metals that have been annealed after cold working preferred orientations may be present. It is perhaps logical to assume that such marked parallelism of structural elements would be manifested by directional properties in the metal. As a matter of fact, tests on many kinds of materials have shown differences in varying degrees. In recognition of this condition, proper design, for many purposes, places the fiber axis in such a way as to present the direction of maximum strength to the greatest applied stress. Earlier Investigations Howe2 has written at considerable length regarding the causes and practical significance of fiber in steel and wrought iron. His studies showed that wrought iron and the puddled steel sheets (materials of plastic origin) were weaker transversely than longitudinally. The transverse deficit ranged from 5 to 29 per cent. The longitudinal tests

Jan 1, 1931

By G. Sachs

According to Tammann,' the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes Ïn properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by Ewing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931

By P. A. C. Wilson

Instantaneous outbursts of carbon dioxide in coal mines have occurred in Germany only in one part of the Waldenburg-Neurode mining district.' This mining region comprises the northeastern fold of the "Innersudetian" coal basin. The basin (Fig. 1) is in the form of a geologic trough approximately 60 km. (37 miles) long and 30 to 35 km. (19 to 22 miles) broad and is enclosed on three sides by ancient truncated mountain ranges—the Riesengebirge, the Bober-Katzbachgebirge and the Eulenge-birge. Only the southeastern part of the trough is not enclosed by mountains of older rock formation. The floor of the basin before the building up of the coal measures was formed on the western, northwestern and northeastern borders by the material from Archean rocks (gneiss and mica schists); in the northern part over this was deposited the Silurian formation. The carboniferous period is represented both by the Lower ("kulm") and Upper Carboniferous, with an unconformity between the stages; that is, the kulm was tilted up and partly eroded before the Upper Carboniferous was deposited. The kulm is a salt-water formation (with marine fauna) but Upper Carboniferous rocks are nonsaline water deposits, with fresh-water flora only. The Lower Silesian coal measures were thus formed in a lime basin fed by the running water coming down from the mountains. As already indicated, the bottom series of the Upper Carboniferous formation, termed "Waldenburg strata" were laid down unconformably on the Lower Carboniferous. Over the Waldenburg strata there are the "Weisstein strata," an intermediate barren stage without coal beds, 400 to 500 m. (1300 to 1600 ft.) thick. Another unconformity followed, which is overlain by the '(Saarbrucken" series, which contain the upper coal measures, and the ('Ottweil" strata. In the last named, it is only on the southwestern fold that beds of coal are developed.

Jan 1, 1931

Incidental to the progress of a geological survey of the Kalgoorlie goldfield during 1927-28 a number of specimens of telluride minerals were obtained, chiefly with the help of Mr. F. G. Brinsden, general manager of the South Kalgurli mine, and Mr. Ernest Williams, general manager of the Boulder Perseverance mine. This collection was supplemented by a number of small specimens, including the rare copper telluride, which were collected and preseryed from the Kalgurli mine by Mr. A. E. Paton, and also by a few miscellaneous specimens from the collection o{ Mr. S. F. C. Cook, of the Palace Hotel, Kalgoorlie.An extensive knowledge of the rare tellurium-bearing minerals was compiled during the last century from occurrences in Transylvania and Colorado. The recognition of different species has been based on chemical analyses and crystallographic measurements. In a few species there has been an absence of crystalline form, and these, together with the discoveries in this century of rickardite and "weissite" muthmannite and empressite, have depended chiefly on the chemical analysis for identification. On the other hand, the crystalline form of nagyagite and stiitzite has been described in detail, while their precise chemical formulae were doubtfully defined.

Jan 1, 1931

By F. R. Hensel

ACCORDING to statements by Guertler,1 Smith and Hamilton were the first to study the copper-titanium alloys, but owing to the presence of large amounts of impurities their data are inconclusive. M. A. Hunter and I. W. Bacon later investigated the electrical conductivity and the temperature coefficients at room temperature. The present writers reported their results2 in November, 1930. Recently Droll published data on copper-titanium alloys3 which agree closely with those obtained by the authors. MATERIAL TESTED The titanium used was in the form of square sintered rods, the analysis of which runs as follows: titanium, 95.4 per cent; silicon, 0.7; iron,1.8; aluminum, 1.4; copper, 0.1; manganese, 0.05. . The ingots were prepared in a high-frequency induction furnace in air atmosphere. Their analyses are given in Table 1. Up to 5 percent titanium the alloys could be forged. Above that amount they were red short and broke up easily. Owing to their rapid absorption of nitrogen and oxygen from the air, the alloys with the higher amounts of titanium tend to form surface films which greatly increase the casting difficulties, especially when small masses of metal are handled. It was, however, possible to prepare sound ingots up to 25 per cent titanium.

Jan 1, 1931

By T. A. Rickard

It has been stated, by Sir James M. Barrie, that "the man of science appears to be the only man who has something to say, just now-and the only man who does not know how to say it". The friendly jibe of the novelist contains enough exaggeration to make it humorous to the followers of Huxley and Spencer; but could any litterateur poke similar fun at the exponents of the avowedly utilitarian branches of science-the men of technology-without suggesting an unpleasant truth? Indeed the engineer does bungle language deplorably. He makes a fetish of efficiency, yet he shows no regard for the effective use of one of his most important tools-the pen; he believes devoutly in accuracy, yet he employs an instrument of precision as carelessly as a small boy handles a gun. This inconsistency may be due to causes such as were indicated by the Academic Senate when it undertook to explain the defective writing of the; students in this university.* The Senate suggested that the student is "constantly subjected by his environment to the unedifying influence of myriad examples of poor English", and that he is also affected by "a certain public prejudice against correctness of expression ". With these statements most of us will agree. Our local newspapers, for instance, tend to spoil the student's taste for good English; later in life, as an engineer, his daily contact with illiterate men inclines him to careless speech and slovenly writing. As

Jan 1, 1931

By T. D. Yensen, N. A. Ziegler

The elements aluminum,' arsenic,2 silicon,3 tin2 and vanadium,~.~ when used in relatively small amounts as alloying elements, seem to have a beneficial effect on the magnetic properties of iron—i. e., they increase the maximum permeability and decrease the coercive force—whereas there are definite indications that boron,5 carbon,6 nitrogen: oxygen," phosphorus16 sulfur6 and titaninum,~ as well as the metals of and adjacent to the ferromagnetic group, nickel,~ cobalt,1° copper," and manganese,% have a detrimental effect on these properties. The effects of calcium4 and magnesium4 are small, if any, while the effect of chromium12 in small amounts is unknown and in large amounts is generally detrimental. WeveR's Classification13 All chemical elements may be divided into three classes based on their effect on the allotropic transformation points of iron. Class 1 contains the nonmetallic elements (except phosphorus) and these lower the A3 point and raise the A4 point. Class 2 contains the common metals and

Jan 1, 1931

By W. W. Adams

Lower accident rates were the outstanding feature. of the second annual sand and gravel safety competition conducted in 1930 by the United States Bureau of Mines in cooperation with the National Sand and' Gravel Association. Both the frequency and, severity rates for accidents were greatly reduced as compared with those shown by the first year's contest, that for 1929. Three times as many plants were enrolled, and the number of man-hours of work represented was more than doubled. Seventy-six sand-and-gravel plants, situated in 20 States, participated in the Competition, as compared with 26 plants, located in 13 States, in the year before. The number of man-hours of employment, which indicated the amount of exposure to occupational hazards, was 4,915,592, an increase of more than 100 per cent over the previous year's total of 2,259,572 hours. The frequency of accidents declined from 74.4 per million hours for all plants enrolled in the first year's contest to 42.7 per million man-hours for all plants enrolled in 1930. The accident-severity rate was reduced from 9.7 days of disability per thousand man-hours of exposure in 1929 to 5.9 days of disability per thousand man-hours of exposure in 1930. The actual number of accidents reported for 1930 by 76 plants included four deaths and 206 injuries whereas the 26 plants that were enrolled in 1929 reported three fatalities and 165 injuries. Under the rules of the contest all "lost-time" injuries are reported--that is, all injuries that disable an employee for more than the remainder of the day on which the accident occurred. If the employee is physically able to resume his work on the day following the accident, the injury is not classed as a lost-time injury. The contest covered accidents and man-hours worked by all employees at the plant who were employed by the same company, and included work up to the point of delivery of the material directly to consumer or to independent agency of transportation--in other words, to point of relinquishment of control of the material by the producer.

Jan 1, 1931

By H. C. Vacher

THE limiting concentrations of carbon and oxygen which may co-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen .thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation with elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Herty1,2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550° to 1600 C. and one atmosphere pressure. Kinzel and Egan3 have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550°. C. In. order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume. a value of 0.0102 at 1580° C. for this

Jan 1, 1931