Search Documents

By H. E. Nold

ThE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained. For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. Periodic Kilns Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues throughout the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1934

At its meeting on February 21, 1933, the Board of Directors the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1934

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By H. L. Hopkins, OHIO, L. W. Kemph, CLEVEL AND, E. V. Ivanso

A balanced system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internaI stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced during the commercial heat treatment of aluminum alloy products. As the industrial use of aluminum increases, it is inevitable that products of increasingly large volume will be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling from elevated temperatures is that of the size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high elastic limits. On the other hand, all commercial aluminum alloys have relatively high thermal conductivities, no invariant phase changes, and the quenching temperatures are comparatively low. In the absence of invariant phase changes involving change in the type of crystallographic lattice, the fundamental basis for the development of internal stress

Jan 1, 1934

By T. G. Chapman

This paper has been abstracted from a forthcoming Bureau of Mines bulletin on the concentration of copper ores in North America. GENERAL DEVELOPMENTS IN CONCENTRATING COPPER ORES FROM 1912 TO 1932 During the east 20 years the milling of copper ores as practiced in the larger concentrators has chanced to such an extent that comparatively few of the machines in use at the beginning of this period remain in service today. Concentrating Practice in 1912. In 1912 the usual equipment for concentrating copper ores comprised jigs for the coarser sizes, tables and sand vanners for the intermediate sizes, and vanners for the finer crushed and ground material. Rolls operated in series under graded crushing conditions, were in common use for the liberation of the copper minerals; grinding by Chilean or Muntington mills ordinarily was confined to the coarser tailings of jigs and tables.

Jan 1, 1934

By John E. Lanning

During the last decade, since most smelters have included Cottrell plants as standard equipment for the removal of dust from furnace gases, it has become apparent that smeltermen have had a new problem slowly developing. This problem has manifested itself in accelerated destruction of, or serious injury to, the masonry of flues and chimneys. The masonry either spalls, if the material is of low strength, or acquires large major cracks, either of which conditions attains such proportions that renewals or reinforcing become necessary to maintain the structure in satisfactory condition. This paper describes the failure of a large modern brick chimney to such an extent that its safety was vitally impaired; the investigation of its condition; the methods of restoring satisfactory strength to the structure; and the installation of an acidproof lining. Plant History The Clarkdale smelter of the United Verde Copper Co., which was put in operation in 1915, was primarily a blast-furnace plant. The smelter at Jerome had utilized blast furnaces exclusively, and in the design of the new (1915) plant, blast-furnace smelting evidently was considered of major importance, the smelting equipment consisting of four blast furnaces 48 in. by 26 ft. 8 in. and three reverberatories, each 19 by 101 ft. The latter, supplemented by roasters, were intended mainly for handling dust and fine ore resulting from the crushing operations. The original roasting equipment consisted of six six-hearth Wedge roasters, six more being added in 1917. All gases from blast furnaces, reverberatories, roasters and converters were conducted by means of suitable flues and dust chambers to one central chimney. This chimney, 30 ft. inside diameter by 400 ft. high, is a self-supporting steel structure, lined with 4-in. brick supported on steel shelf angles, riveted to the shell, spaced about 15 ft. vertically. The bricks were of local manufacture, not particularly hard-burned, and were laid in ordinary cement-fireclay-sand mortar. No record is available to indicate that any particular effort was made to secure an acidproof mortar. The same materials were employed in the construction of the reverberatory and roaster flues, and the roaster dust chamber. Parenthetically, it may

Jan 1, 1934

By L. W. Kempf

A BALANCED system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internal stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced luring the commercial heat treatment of aluminum alloy products is the industrial use of aluminum increases, it is inevitable that products of increasingly large volume be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling at elevated temperatures is that of the, size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high

Jan 1, 1934

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural gas through high-pressure pipe lines. This report deals with that part of the study involving the design off pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By Ralph A. Sherman

In these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home. Factors That Govern the Choice of Fuel and Burning Equipment A rational, intelligent selection of fuel and equipment for heating the home would consider two groups of factors: Cost Factors Convenience Factors 1. Cost of potential heat in fuel 1. Attention 2. Efficiency of combustion and heat transfer 2. Dirt 3. Fixed charges 3. Noise a. Interest b. Depreciation c. Repairs 4. Power costs 5. Cost of handling ash and refuse. As just stated, the purpose of this paper is to analyze the relative importance of the five cost factors and not to discuss particularly the relative total costs of different methods of heating. However, to arrive at the percentage costs and to show clearly how they were determined, a statement of the total costs is unavoidable. One example only will

Jan 1, 1934

By L. P. Teas

In spite of the influx of operators into the Gulf Coast anxious to retrieve their depleted production in other fields, and in spite of very active application of the most scientific geophysical methods to locate new producing areas, the results have been very discouraging and the year has failed to produce more than the average results for a Gulf Coast year. During the year seven new oil fields, some of which are still of very little importance, and one new gas area have been discovered. These fields are Tom Ball, Greta, Cleveland, Raisin and Garwood in Colorado County; Louise and Premont in Jim Wells County, and the new producing gas area near Ace in southern Polk County. During the year salt has been found for the first time at Carlos and Esperson. New producing areas have been developed on East Stratton Ridge, Hockley, Hull, Port Neches, near Pettus in Bee County, and on the O'Connor Ranch in Victoria County. The total production for the Gulf Coast for the year was 62,837,435 bbl., an increase of 18,589,000 bbl. over 1932. During the year, 1307 wells have been drilled of which 207 were wildcats, compared with 653 wells and 141 wildcats the previous year. The total daily production at the end of the year was 165,201 bbl. At present there are 3100 oil wells producing. The average production per well is 55.5 bbl. per day. The price of crude fluctuated considerably during the year, beginning at 80c per barrel and closing the year at $1.04 per barrel. Completion data for 1933 are as follows:

Jan 1, 1934

By H. N. Hickey

Wildcat drilling operations in Montana during 1933 did not yield any discoveries of oil or gas that were of major importance. There was comparatively little drilling in the older proven fields, as most of the interest was centered in the Cut Bank field, where 44 wells were completed. The total number of wells completed in the state during the year was 79, of which 62 were productive of either oil or gas.

Jan 1, 1934

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a as supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, sortie fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called "bad gas"--return mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory-scale study of direct oxidation of crude oil.

Jan 1, 1934

By A. W. Gauger

Coal as mined contains varying quantities of inorganic components (mineral matter) which, on combustion, produce the residue known as ash. It has long been realized that the weight of this residue does not equal the weight of the mineral matter originally in the coal, because of the chemical changes that take place during the ashing process. Moreover, the ordinary ash analysis presents the ash as a mixture of oxides with little or no clue to the identity of the mineral species originally present in the coal. It is only for pyritic sulfur that an attempt is made to determine a mineral component. So far as the authors are aware, there are practically no experimental data in the literature as to the percentages of the different mineral species present in coal. The oft-quoted table of Marson and Cobb1 cannot rightly be considered as data, since the authors merely state that the table "shows the probable forms in which these ash constituents exist in coal." In view of the attempts to calculate analyses and determinations of the calorific equivalent of coal to the mineral-matter-free basis, as well as the importance of the mineral species in clinkering, combustion and coking, it seems strange that so few data are available on this phase of coal technology. For example, numerous empirical corrections for use in the scientific classification of coal have been suggested to compensate for the losses from the mineral matter during ignition of the coal to ash. These include multiplication of the ash percentage by various factors such as l 1/10 and 156, the use of the Parr unit coal formula (1.08 A + 22/40 S, where S = total sulfur) as well as certain modifications of the Parr formula that attempt to correct for the organic sulfur present in the coal. Although many experiments have been made to determine the loss on ignition of the clays associated with the coal measures and correction

Jan 1, 1934

By R. A. Brackett

The most effective means of controlling the dust in the drilling of rock has been found after careful investigation to be collection of this dust at the source. By direct collection, all the dust is collected at the collar of the drill hole and deposited into suitable containers. Equipment for handling this work can be either portable or stationary, depending upon the particular requirements and the application. For most work the portable unit is found most advantageous, and with a capacity capable of handling two drills operating simultaneously. Such a portable unit would consist of a metal cap, or hood, placed against the face of the rock through which the drill steel would be inserted. This hood is connected by a flexible rubber hose to a primary separator, where the bulk of the dust is collected. From here a second length of hose connects to the secondary stage of separation, where the fine particles of dust are collected and which is built in as an integral part of the vacuum producer. Hoods are adapted for vertical, horizontal or stope drilling, and mounted so as to become immediately effective when collaring the hole and remain in place continuously. Such dust collectors can be used with either wet or dry drilling. However, in view of the fact that when drilling dry and using the dust collector, the dust count can be maintained within safe limits, wet drilling becomes unnecessary. Furthermore, it has been found that when using the dust collector not only has the dust hazard been eliminated, but also increased footage can be obtained. Samples taken under a wide variation of conditions indicate that where the dust count required is below five million particles per cubic foot, dust collectors will be required. Opreators, in general, accept the use of this additional equipment favorably, and it is generally felt that such means of collecting the dust will soon be universally adopted. Tests made by the Connecticut Department of Health Bureau of Occupational Diseases show dust counts reduced from 203 million particles to 6.05 million by the use of the dust collector, when drilling dry.

Jan 1, 1934

By C. L. Dake

Many proposals have recently been made regarding the broadening of engineering education, often with little consideration of the problems their application involves. The chief purpose of this paper is to point out how many and how complex are the questions that absolutely must be answered, in any conscientious effort to solve the problem of liberalizing engineering curricula. Among proposed additions, more training than is now given has been urged in public speaking, report writing, business law and contra s, general finance, money and banking, scientific management, gene ' economics, economic and financial history, social problems, labor pre lems, public ownership, psychology and similar related subjects. T urge in this direction is widespread and persistent. In discussing the blem, the following questions must be given careful consideration, an he absolutely definite conclusion reached: 1. The Present Curriculum Load.—Is this load actually too heavy? In the face of this load, is there room to add broadening subjects to our curricula? Can elimination of present subject matter make room for such additions? Can an elective system accomplish the desired end? 2. Problem of Early Specialization.—Is early specialization a weak ness? Is industry forcing early specialization? Do our varied degrees demand early specialization? Can broadening be harmonized with the present degree of specialization? 3. Graduate Work to Solve the Broadening Problem.—Can we add the desired work in the graduate school? Are the proposed additions of graduate caliber? Is it desired to reduce graduate standards? Can present undergraduate work be removed to the graduate school, to make room for desired broadening courses? Is graduate work normally broadening, or is it specialization ? 4. Importance of Proposed Additions.—Will they increase entrance salaries? Will they increase the engineer's efficiency? Will they raise

Jan 1, 1934

By G. A. Hellstrand

IN 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-New-foundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicat-ing about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereon, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company's metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company's testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods, under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere.. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1934

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given be- low. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1934

By Charles R. Wraith

The property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N'dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13" south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is profusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposcs, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are conveniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for " dolly " mud and for lining launders is available within a short distance of the smelter. Metallurgy Copper is contained in the ore as chalcocite, chalcopyrite and bornite. Chalcocite predominates in the eastern end of the orebody almost to the exclusion of other copper minerals. The amount of chalcocite decreases with a corresponding increase of chalcopyrite and bornite toward the western extension, where the latter predominate.

Jan 1, 1934

By W. A. Selvig

BY plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Com-mittee on Coal Classification. This scheme was sponsored by Sub-committee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic.. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as follows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group, 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. , The lignitic class of coal was divided into two groups both below 8,000.B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934