Search Documents

By Paul M. Tyler

The value of mica depends chiefly upon the size of the flat sheets into which it can be split and also upon whether it is clear or stained. Muscovite (white mica) and philogopite (amber mica) are the micas of commerce. Biotite (black mica) and other varieties are virtually unsalable. Vermiculite, an altered mica having the extraordinary property of expanding greatly when heated, preferably should not be classed commercially as mica. Mica is marketed as (1) cut or uncut block, (2) sheet, (3) splittings, and (4) wet or dry ground mica. In the United States, mica that will not yield flat films over about 1-1/2 inches square, or that is ruled, rumpled, or flawed in any way, can be sold only as scrap, its sole use being for making ground mica. Only sizes that will yield rectangles 1-1/2 by 2 inches or larger can be classed as sheet quality; slightly smaller sizes may be classed as punch, and under certain circumstances still smaller sizes, down to about 1 inch square, may be used for splittings, which are mostly a thousandth of an inch thick or even thinner. Splittings, however, are produced in large quantities only in British India, where labor costs very little. Even there the work is done mostly by children, who not only work cheaper but have a delicacy of touch that enables them to do the splitting faster and better. No mechanical process yet devised will permit ordinary splittings to be made economically in the United States.

Jan 1, 1938

By Walter C. Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1 1/3 miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1938

[~lis is the f'fth in a ~erieG of reports on properties of commercial motor fuels, made in accordance 1,'Vi t:h fl cooperative ae,ree-ment betwGon tho Cooperative Fuel ReRRarch (e.F.R.) Committee and the Bureau of I ines of the Dcpart~ent nf the Interior. The first report gave data on motor r-asolino~ sold during the wintor of 935-36.31 Thi~ report covers 84 brands of ga~oline represented by l,722 samples exclurling the Pacific Coast. T 3)Se J.rom th~. ?~'tcific Coast IV .ro avnrL)f:od b~r tho Pacific Coa!3t tecilnical group "bofore o8ing submi ttcd ruld arc p~.lbl:'shcd GX Gtl~r as they were submi tted. In some areas r~lJort~ . erc roceivod f~om ~ ix to eicht compD.l1ie~ on the same brands of gasoline. whoruar. in other areas only one company reported on a brond. Thut., it CU .. "! be senn that BO .. 0 uf the dnt ;.U'e more rCY>l'c entat vc thM others. The inclusion of r~0rts fro:n several ci tie. w' thin somo of tho di stricts has ir.rpr,)vcd the report by reducinc; tr.e numb~r of brand rcportel by only ono company.]

Jan 1, 1938

By Albert Hoskinson

PROGRESS on the earth depends to a large extent upon the rapid inter-change of ideas and commodities between the various nations of the world. The smooth flow of commerce, by which these ideas and com-modities move, is accelerated by accurate and complete maps of the various land and water areas of the earth, The production of accurate maps depends upon a complete knowledge of the figure and dimensions of the object to be charted, therefore a knowledge of the shape of the earth is a prime necessity for accurate charting purposes. Gravity observa-tions were first undertaken to aid in determining the shape of the earth so that the geodetic surveys of its land and water areas might be more accurately connected to form an undistorted map. A large part of the earth's surface is water and it is therefore necessary to get gravity values at sea as well as on land before a complete and accurate figure of the earth can be determined. Dr. F. A. Vening Meinesz, of Holland, was the first scientist to perfect a pendulum instrument that would accurately measure gravity at sea. He had previously developed a multiple pendulum apparatus for measur-ing gravity upon swampy and unstable land areas in Holland and it was therefore quite natural that he should adapt the instrument to give accurate results upon a still more unstable support, the surface of the sea. His instrument as perfected gives satisfactory results when mounted in gimbals on any vessel where the roll and pitch are not more than about 5° and where the vibrations from rotating machinery and wave action are not large enough to cause the pendulums to shift on the knife-edges. This degree of stability can be obtained on surface craft only in protected waters or on very calm days. Therefore, Dr. Meinesz mounted his instrument in a. submarine so that he could submerge below the disturbed surface waters and get the desired stability in nearly any kind of weather by simply diving to greater depths. Most of the gravity-at-sea work has been done with a Meinesz instrument and a very large number of the observations have been made by Dr. Meinesz himself. He has occupied nearly 1000 sea stations and probably has traveled as many miles by

Jan 1, 1938

By E. H. Denny

IN the past few years many men, including technically trained engineers, have been asphyxiated in metal mines, coal mines, tunnels and surface wells where a few relatively simple precautions with regard to ventilation and air testing would have saved them. Death from mine gases is analogous in some respects to death from poison and from drowning. The respiratory passages of a victim who has breathed oxides of nitrogen from burning explosives are badly irritated and a few hours or even a day after exposure he may develop a quick and fatal pneumonia; if, however, he enters without respiratory protective apparatus an atmosphere deficient in oxygen (a condition that may occur in unventilated or poorly ventilated parts of all underground mines) he collapses and if not rescued dies more quickly and surely than a lone nonswimmer who falls suddenly into deep water. An example of an atmosphere virtually without oxygen was demonstrated by an air sample taken by a Bureau of Mines engineer wearing oxygen breathing apparatus in a Cripple Creek shaft some years ago, during the recovery of the bodies of two victims of asphyxiation; analysis of the sample by the Pittsburgh laboratory of the Bureau showed the presence of 18.40 per cent of carbon dioxide, 0.27 per cent of oxygen, and 81.33 per cent of nitrogen, although the atmosphere apparently was clear and normal. In a mine one can pass from good, breathable air to an atmosphere that will kill as quickly as one can dive from a board to deep water below. SOME INSTANCES OF ASHYXIATION BY GASES IN METAL MINES The following typical examples of comparatively recent instances of asphyxiation in metal mines were taken chiefly from reports of various kinds of the U. S. Bureau of Mines.

Jan 1, 1938

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

Jan 1, 1938

By H. Dale Nichols

[The growing importance of the Sundance (Jurassic) formation as a source of oil in the Rocky Mountain area has prompted the making off a series of porosity determinations of core samples collected from the reservoir sands of the Lance Creek oil field, Niobrara County, Wyo. These analyses are preliminary to a study of fluid and energy relations in the Basal Sundance reservoir of that field, and the determinations of porosity will be used in subsequent studies requiring calculations of the volumetric capacity of the reservoir and estimation of the reserves of oil and gas.]

Jan 1, 1938

[ ]

Jan 1, 1938

[ ]

Jan 1, 1938

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been puplished5/ describing apparatus and tests made on anthracite to determining the amount and composition of the oxidation products when normal dry air was passed through it at temperatures varying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative prorortions varied with the temperature. From: these results, graphs were prepared by which `he temperature at which the coal was oxidized could 'be estimated, thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

Jan 1, 1938

By Roy E. Dickerson

No important new developments took place during the year 1937 in Cuba. Estimated figures are as follows: Bacuranao field, 100 bbl. per day petroleum; Motembo and Vesubio areas, 120 bbl. per day natural gasoline.

Jan 1, 1938

By R. A. Bowen

THE Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE OCCURRENCE AND CHARACTERISTICS The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and clips north at approximately 62°. The dikes dip south at 45° and bear north 20° from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted ,by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the inter-section of hanging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chest interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging (like. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1938

By The Staff

THE gold mining industry in Canada is today the most important stabilizing influence in the country. This factor was brought out particularly during the 'depression' years, when steady employment was given to men in that industry and the monies spent in supplies and power in turn benefited the country to a great extent. At the same time, a commodity was produced which was saleable in any market of the world, thus maintaining Canada's credit in foreign markets and keeping her trade balances equalized. We have a vast area known as the Precambrian Shield. The agricultural possibilities of this area are practically negligible and it will depend entirely upon the mineral and forest resources to make this district an economic factor in the life of Canada. To date, from the mineral point of view, we have been highly successful. There are, however, still vast areas to be explored. It is tedious and laborious work, entailing great individual hard-ships and the expenditure of much energy and money. During my thirty years' experience in the search for, and operating of, gold mines, I have come to the conclusion that although individuals may give all their time, energy, and money, Governmental assistance is absolutely necessary in the development of hydro-electric power sites and roads. The Governments, to date, have given splendid co-operation along these lines, but in order that this great industry may go ahead they should continue their good work and, if possible, give greater relief from taxation to mines situated at a considerable distance from the railway.

Jan 1, 1938

Jan 1, 1938

[ ]

Jan 1, 1938

By R. E. Heithecker

[The principle of determining volumes of liquid by alternately drawing in and discharging given quantities of the fluid from a confined space or compartment of known volume and mechanically counting the number of displacements is well established. This is true particularly in water measurement. For several years, oil meters employing the same basic principle have beer, used for gaging oil production from individual wells, groups of wells, and in some areas for metering the entire production from a property. Especially in areas where there is town-lot drilling and space for tankage in at a premium, oil meter have been used successfully to gage the oil. This facility has obviated the necessity of installing gage tanks. Oil meters also have been used in pip-line and refinery operations and in loading tankers. Present knowledge of the subject shows that positive-displacement oil meters can be used for measuring crude oil in the field and elsewhere, provided the meter-counter mechanism is in proper adjustment and the oil has been studied sufficiently to determine the proper factor to be applied to the volume as registered by the meter, making possible the adjustment for the shrinkage of the oil caused by liberation of gas from solution.]

Jan 1, 1938

By J. B. Littlefield

[Ata. meeting of the Subcommi ttce on Chemical _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of Mnes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a reference method. 'I'ests ~ ere made aJ,so to aScer ain the effici ency of the recently developed midget i;npi gerS..! for collac ing lead dust. For comparative pur-poses, samples collected by tte large impinger wore included.]

Jan 1, 1938

By Oliver Bowles

When a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibilities of much wider application. A wire saw consists of a 3/16-in. or ji-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1. The teeth of the saw are sand grains carried in the grooves between the strands. Accomplishments in Slate† Initial experiments with wire saws by the U. S. Bureau of Mines in the Colonial Slate Quarry, Wind Gap, Pa., in 1926, attained success so immediate and pronounced that within two years in virtually every quarry in the neighborhood of Wind Gap, Pen Argyl and Bangor, the most productive slate area in the United States, wire saws were substituted for channeling machines. An 80-ft. cut in slate is shown in Fig. 2. The technique of operation has been described in several reports (references at the end of the paper). The present purpose is to summarize the accomplishments in a large, typical slate quarry after nine. years of experience. Parsons Bros. Slate Co., at Pen Argyl, Pa., substituted two wire saws for six channeling machines in 1927. The following comparisons are made between the present method with wire saws and the former channel-ing-machine method. Rate of Sawing.—The average rate of cutting with a wire saw in the early days of its operation, as determined by the Bureau of Mines', wits 14 to 17 sq. ft. per hour. Parsons Bros. Slate Co. estimates the present rate of cutting at about 25 sq. ft. an hour, whereas the channeling-rnarhirle

Jan 1, 1938