Search Documents

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

A special committee on the Classification of Surface Mining Methods was appointed by the A.I.M.E. Board of Directors on Nov. 17, 1939. The committee was headed by Gerald Sherman, and the members were Chester A. Fulton, C. F. Jackson, Earl E. Hunner and Arthur Notman. The following form of classification was reported to the Board by the Committee on May 16, 1940, as its unanimous recommendation. SURFACE MINING Dry Mining Bottom Benching Bank Mining < Top Benching Dry Mining Dry Mining Bottom Benching Hydraulic Mining Pit Mining Dredging Dry Mining Top Benching Wet Mining Top Benching River Bed Dredging Subaqueous Mining Lake Bed or Dredging Ocean Bed (Hand Mining Ground Sluicing Hydraulicking Dredging In most cases the terms used in the accompanying outline define themselves. Bank Mining is distinguished from Pit Mining by its situation. In Pit Mining the ore is taken from an operation below the level of the surrounding surface. In the secondary classification, Bottom Benching is an operation in which a bench is attacked from below, but the material mined might be hauled up out of the pit or moved out horizontally or downward.

Jan 1, 1940

By William Carton, Cyril U. Cooledge

BecauSe the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It mas clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stapes below with disastrous results to men and mine. The method of mining developed during the years 1928,1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. Geological Structure The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1940

By Bruno V. E. Nordberg

Hoisting is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.&apos; In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michigan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualistic types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By T. Suzuki

LABOR. conditions have finally caused rock-drilling machines to supplant hand drillers in the Japanese mining industry, and have encouraged this study. During a period of three years 25,000 tests were made on 67 different American, Japanese, and European rock drills, using, respectively, the Paynter testing machine, and drilling in granite and limestone. Recorded were: air consumption, speed of rotation, torque of rotation, foot-pounds of striking energy, air pressures, input horsepowers, and speed of rock penetration. The author expresses his views on the interrelation of these factors and offers theoretical support, as well, by formulas based upon the mechanics of impact. He discusses the different designs of the valves, cylinders, piston hammers and rotation devices involved in the different types of rock drills, with respect to their merits and defects and offers conclusions about the factors that should be considered in the new design of a superior rock drill. The author&apos;s mathematical demonstrations and arguments for a value of "best feed clearance" of the drill bit from the rock are based upon the hand-operated screw-fed type of hammer drill. Automatic feeds have not been considered in this paper except for the tests on one drifter with air feed, 10 air-feed stopers, and some hand-held blockholers. The following classes of drills, with one of each model, size, or type, were tested: 23 heavy drifters, 34 light drifters and hand-held drills, and 10 stopers. They represented the following makes and models: 40 from the United States—namely, Ingersoll-Rand 18, 148, L-74, 24-70, N-72, N-75, R-72, 26, BAR-33, BCR-430, DCRW-23, RA-12, CA-31, CC-11; Denver 7, 107, WT-21, WT-31, WT-331, WT-337 (models WT with motor rotation, screw feed), 11, Waugh 93, 95; Waugh 16; Sullivan DR-6, DW-64, T-3; DP-321, DP-331; DA-21, DT-44, DT-421; Gilman AX-321 (motor rotation and air feed); Cleveland D-5; AIBQ, 44-SWR,

Jan 1, 1940

By Robert C. Berggan

The hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for conventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs.1 Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Washington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned. The Process Hot-milling performs the function of re-dressing the bit at a forging temperature of about 1650°F., by the removal of metal from the flutes with a milling cutter, followed by a similar cut from the bit gauge. Conventional bits are thus treated following the usual forging operation in a sharpener, and usually in the same heat.

Jan 1, 1940

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By Felix B. Shay

The Agua Fria mine is in eastern Honduras at Lat. 140" 06&apos; N., Long. 86" 36&apos; W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Tegucigalpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle Y. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 Ib. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo servicc. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced. The nearest site for an airport was two miles north of the mine. The necessary grading was done by a small track-type tractor with a wheeled grader, which was brought in overland. Six weeks was required for bring-

Jan 1, 1940

By E. H. Denny

In the past few years many men, including technically trained engineers, have been asphyxiated in metal mines, coal mines, tunnels and surface wells where a few relatively simple precautions with regard to ventilation and air testing would have saved them. Death from mine gases is analogous in some respects to death from poison and from drowning. The respiratory passages of a victim who has breathed oxides of nitrogen from burning explosives are badly irritated and a few hours or even a day after exposure he may develop a quick and fatal pneumonia; if, however, he enters without respiratory protective apparatus an atmosphere deficient in oxygen (a condition that may occur in unventilated or poorly ventilated parts of all underground mines) he collapses and if not rescued dies more quickly and surely than a lone nonswimmer who falls suddenly into deep water. An example of an atmosphere virtually without oxygen was demonstrated by an air sample taken by a Bureau of Mines engineer wearing oxygen breathing apparatus in a Cripple Creek shaft some years ago, during the recovery of the bodies of two victims of asphyxiation; analysis of the sample by the Pittsburgh laboratory of the Bureau showed the presence of 18.40 per cent of carbon dioxide, 0.27 per cent of oxygen, and 81.33 per cent of nitrogen, although the atmosphere apparently was clear and normal. In a mine one can pass from good, breathable air to an atmosphere that will kill as quickly as one can dive from a board to deep water below. Some Instances of Asphyxiation by Gases in Metal Mines The following typical examples of comparatively recent instances of asphyxiation in metal mines were taken chiefly from reports of various kinds of the U. S. Bureau of Mines.

Jan 1, 1940

By John L. Boardman

The Anaconda company has never indulged in any employee activities at Butte which might be termed paternalistic, but it has exerted a vast amount of effort in care of its employees during working hours. The reason for this policy is not lack of interest or that the company does not feel the effect of employees&apos; activities while they are "off the job"; it is that the company and the city of Butte have grown up together and each has been adequate in its own sphere, the company in providing employment at the highest possible wage and the city in providing housing, sanitation, commercial services, medical services, schools, churches, amusements and entertainments. The one exception to this independence between the company and the community is the Butte Water Co., which is a wholly owned subsidiary of the Anaconda Copper Mining Co. Mention of this relationship is made here because the water supply of such a city as Butte is one of the principal factors in determining the health of the people. Very early in the development of the Anaconda company an adequate and dependable water supply for the operations became necessary, therefore the company took over this important community function. So well has this activity worked out that during the whole period of time covered, in which the company has expanded to become practically the sole mine operator and the community has grown from a small mining camp to the status of a modern city, there has been no shortage of water or any outbreak of water-borne, epidemic disease. Conditions Leading to Organized Safety Effort A brief sketch of conditions in Butte prior to 1912 is necessary to an understanding of the reasons for placing accident prevention on an organized basis. As early as the year 1884 there were a large number of small independent mining operations depending principally upon the production of silver, although even then copper was becoming prominent in the value of total production for the district. The Butte camp was then just emerging from the log cabin stage to that of a modern city.

Jan 1, 1940

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. Temperatures and Underground Waters Surface Temperatures.—The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the downcast shafts; however, the variation between winter and summer causes a difference of only 2" to 3" in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.—Rock temperatures on the deeper levels of the mine are as follows:

Jan 1, 1940

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By Willis H. Carrier

Particular interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world&apos;s deepest mine, the Turf shaft of the Robinson Deep in Johannesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly newl-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104" at sea level, insured reasonable safety, since all parts of the machine operated at subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1940

By Donald E. Cummings

Measures appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-l9 has accumulated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors—the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Control of the danger arising out of prolonged contact with pernicious airborne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects—one, medical; the other within the province of the engineer. I—Factors Comprising Degree of Individual Susceptibility Thorough investigations conducted among miners who have labored for years in the presence of recognized silicosis hazards usually reveal an impressive difference in the injury incurred by men whose exposure to dust has been nearly identical. After a quarter century underground, one individual is short of breath and incapacitated with miners&apos; complaint, while a fellow workman suffers no pulmonary embarrassment and is in good health. Physicians ascribe this oft-observed difference in reaction to individual susceptibility and express a universal regret when they deplore the fate that chose to make the predisposed youth a miner rather than a farmer. To trust the health of miners to fate at the present time is even more unfortunate, because many of the factors that influence man&apos;s susceptibility to dust are known, and can be accurately determined by competent medical methods. Among the most important factors comprising susceptibility to injury by dust are the anatomical peculiarities of the individual&apos;s respiratory mechanism, his physiological response to the inhalation of dust, his previous dust, exposure, the existence of pulmonary infections or other pathological processes in his lungs, his age,

Jan 1, 1940

Jan 1, 1940

By L. C. Campbell

The purpose of any accident-prevention program is the curtailment or entire elimination of injuries and fatalities. It is a job that is never finished in the coal-mining industry. Day by day, on shift and off shift, men are exposed to injury and death in varying numbers. Seldom is it possible to lock up at the end of the shift and leave a mine plant in the care of a sleepy watchman, as can be done at most manufacturing plants. Even on off shifts there are maintenance and supply crews, coal cutters, pumpers and ventilation men exposed to danger. The prevention program of The Koppers Coal Co. recognizes two primary facts: First, no program can be successful without the full support of the management and complete knowledge of the job at hand on the part of every supervisor. Second, and equally important, is the full cooperation of every employee in observing the safety rules and practices set up by the management. Conscious day-to-day concern for his safety by the individual worker is the longest stride toward a good safety experience. How to accomplish the education of the individual worker and supervisor for safety is the problem of The Koppers Coal Co., as it is the problem of all coal companies. Safety Rules A simply stated set of Safety Rules and Practices for the government of employees is the starting point with The Koppers Coal Co. There are but 13 of these rules, which are short, easily understood and followed by a campaign of education and inspection. Each employee receives a set of these Safety Rules and Practices and signs a receipt for them, which is bound in at the back of the booklet, and this receipt becomes a part of his employment record. These rules and practices are as follows: Introduction The following rules have been compiled for the safety of employees and are established according to rules number one and number two of the official bulletin

Jan 1, 1940

By C. G. Brehm

The anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal measures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof support and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches. The Lower, or Southern field, is made up of basins of great depth, some being 4000 ft. deep, and its measures are mostly on very steep pitches. In certain sections this Southern field is being mined at an elevation of 1300 ft. below sea level, on a pitch ranging from 50&apos; to practically vertical, and because of the tremendous pressure and the inherent gas in the seams, outbursts of coal frequently occur at the face, locally known as "bumps." These outbursts are accompanied by a rumbling noise, after which gas is usually found. This condition makes mining a difficult and extremely hazardous undertaking, and unusual skill is required on the part of the miner to drive and maintain openings necessary to the production of coal. Miners working in such seams on the heavy pitch must carry face batteries (Fig. 1) to afford proper protection while working at the face, because of the outbursts and free running coal. To drive haulageways or gangways in this field it is

Jan 1, 1940