Search Documents

By Leah L. Naugle, H. H. Lowry, H. G. Landua

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its ('Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

IT is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investigators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from 1100° to 1706°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxidation of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous days burned to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,5 the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery6 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the day, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. Orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By Kendall E. Born

Production of crude oil in Tennessee during 1941 was slightly more than 15,000 bbl., about the same as in the preceding year. Two thirds of the total was from the Mississippi limestone pools in Scott and Morgan Counties. About a dozen small scattered wells in Clay, Pickett, and Fentress Counties, pumped irregularly, produced approximately 5000 bbl. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production by counties is shown in Table I. Drilling activities in the state fell to the lowest stage since 1933. Twenty-seven wells were spudded in during 1941, of which six were drilling or only temporarily suspended on Dec. 37, 1941. Of the 22 completions, four were gas wells of undetermined quantity, but are classed as commercial, and 17 were dry or near-dry holes. One well encountered oil, but it has not been tested. The total footage drilled during the year was 29,916 ft.; the average depth of wells was 1359 ft. The more important wildcats are listed in Table 2; the distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 3480 ft. in northwestern Anderson County, in the highly disturbed Appalachian area, a region long considered the most unfavorable in the state for the accumulation of oil and gas. Another test is now drilling below 2000 ft. in this general area. Cumberland Plateau.—There were two completions in the Cumberland Plateau area. One test, drilled in northwestern Scott County in an area of former Mississippi limestone production,' encountered a considerable amount of free oil at 850 ft., about the same horizon as in the old abandoned wells. No pumping tests have been made to date. A well at Oneida, Scott County, found gas at 1579 ft. in a sandy limestone of lower Mississippian age. The volume was reported doubled by a shot, although no open-flow measurement is available. Eastern Highland Rim.—Six completions on the eastern Highland Rim resulted in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area tested the upper part of the Knox dolomite group, one of which encountered some free oil in a sandy dolomite at 1670 to 1681 ft. A test high on a well-defined structure in Clay County found a considerable amount

Jan 1, 1942

BIRINGUCCIO was born in Siena in 1480, the son of Paolo and Lucrezia di Bartolommeo Biringuccio.* He was baptized on October 20 of that year with the given names Vannoccio Vincenzio Austino Luca. His father appears to have been an architect, for in 1504 he was paid 600 scudi for his work on the walls of the Communal Palace and at the same time he was superintendent of streets for the city. The course of Biringuccio's life followed closely the checkered fortunes of the Petrucci family of Siena. A warm supporter of Pandolfo Petrucci, Biringuccio did not falter in his allegiance to the family and their party during his lifetime. It was probably to the protection and patronage of this lord that he was indebted for the opportunity to travel widely through Italy and into Germany during his early years and so to lay the foundation for the extensive knowledge of the subjects he was to describe in the Pirotechnia. In 1507, as he himself indicates (p. 48), he was 'in Friuli and. Carnia in northern Italy after having traveled in Germany,, and he also visited the, brass, works in Milan. After returning to Siena; he was sent by Pandolfo to direct the iron mines in near-by Boccheggiano. When Pandolfo died in 1512 (in which year Biringuccio's s father also died), Biringuccio continued to support the Petrucci family in the person of Pandolfo's son, Borghese, who succeeded, to the rule. Under his patronage, Biringuccio was appointed to a post in: the Armoury of the Siena Commune in 1513. In ISIS a popular uprising forced Borghese and his followers, including Biringuccio, to flee from Siena. Biringuccio and the goldsmith Francesco Castori, head of the mint, were accused of having debased the coinage alloy with the knowledge and consent of Borghese. When he failed to appear in 1516 to answer these charges-which may well have been invented by the opposing political faction-Biringuccio was declared a rebel and was exiled as a traitor to the Republic. He then traveled about Italy, was in Rome and Naples, and visited Sicily in 1517.

Jan 1, 1942

By A. William Johnson

It was pointed out in an earlier paper1 that our understanding of the atomic mechanism by which diffusion occurs in metallic alloys is scarcely in an advanced state. This unsatisfactory condition is the result not of any lack of interest, but of the difficulty of designing experiments that .will yield suitable data. The diffusion coefficient of an alloy, measured in the usual way, is simply a number specifying the rate of homogenization of a nonhomo-geneous metal; this number, of itself, can furnish neither the rate at which the individual atoms move nor information as to the mechanism by which they move. It does not necessarily follow, however, that such information cannot be obtained, even if the path to be followed is still not clear. Much success has been attained in the study of diffusion in ionic crystals. A number of experiments, for which there are few counterparts in connection with metals, yield information often indicating a detailed mechanism by which diffusion probably occurs. From such work, quite acceptable theories of lattice imperfections have been developed by Wagner, Schottky, Frenkel, Jost and others.2 It is postulated that real crystals of stoichiometric composition contain, in equilibrium, certain imperfections of which the most importarlt types are: (I) vacant cation sites, with an equal number of interstitial ions; (2) vacant anion sites, with an equal number of interstitial ions; (3) equal numbers of anions and cations in interstitial positions; (4) equal numbers of vacant anion and cation sites. The classification of a particular crystal according to this scheme then follows from studies of the variation of electrical conductivity with pressure of the electronegative component surrounding the crystal, with ion size, and with temperature; other physical phenomena, such as the Hall effect, have aided in establishing the classification. The relative mobility of the anion and cation may be determined by chemical analysis of the salt at the electrodes following electrolysis. With such information, and knowing that one ion never occupies the lattice site normally belonging to an ion of opposite sign, it is usually possible to ascertain the diffusion mechanism. It is clear that the same experiments are not applicable to metal crystals, and substitute experiments that yield as much information have not yet been devised. Much can be learned, however, about the mobilities of the two* kinds of atoms in alloys by the use of radioactive metals as indicators. Only one such experiment has been performed in the past. In 1933, Seith and Keil,3 in an effort to explain the great difference between the rate of diffusion of gold in lead and of lead in lead, measured the rate of diffusion of radioactive lead in 3 gold-lead

Jan 1, 1942

IN my opinion antimony* is a composition made by Nature to create a metallic mineral that is overflowing with an undue proportion of hot and dry material and with its moisture poorly mixed, with an effect wholly contrary to the composition of metals. Therefore, it comes to be, like quicksilver, a mineral deformity and monstrosity among metals. Or it might be a material that is about to reach metallic perfection, but is hindered from doing so by being mined too soon. I am persuaded to this opinion by seeing in it so many parts similar to those of metals, considering first its clear and brilliant color and its great weight and then the regulus† that it leaves at the bottom of the vessel on melting. Obviously it has in it much earthiness, as is attested by the odor of its sulphurous burning, its imperfect blending, its defective mixture, its difficult fusion, and finally the character of its regulus, for although this is very white and almost more shining than silver, it is much more brittle than glass. [28] The practical philosophers make great use of it in their alchemistic work in order, they say, to make an oil that they believe gives the color of gold to fixed silver. For this reason many of them hold it in high repute, especially the kind that has long thin fibers like a bundle of bristles. And they say that they can obtain greater results with it than with sulphur. I believe this, however, in case it is aided by sulphur, since it is nearer the metallic species than sulphur is. This I know for a certainty because I have seen them extract from it a bloody liquor in the form of an oil. The alchemist who made that which I saw told me that it had not only the

Jan 1, 1942

By S. S. Clarke

THE opening of zinc-lead ore bodies in the lower chert beds of the Tri-State district, locally called sheet-ground deposits, [ ] presented several new economic operating problems to be solved before the low-grade deposits could be mined profitably. Drilling was the first high-cost problem and loading and haulage difficulties followed. At this time, the sheet-ground mines are producing about 2000 tons per day. GEOLOGY The geology and ore deposits of the Tri-State district have been covered in detail by [ ] Fowler and Lyden.* Briefly, the sheet-

Jan 1, 1942

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution's research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof's rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel's photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

TO metallurgists generally, Arthur S. Dwight is no stranger even to those who do not know him personally. He is one of those contributors to technical progress whose names will go down to posterity because of their being attached to a successful machine or process, such as Dorr, Hardinge, or Marcy, or Wedge, MacDougall, or Herreshoff. The roasting and sintering method and equipment developed by Colonel Dwight and his associate, the late Richard L. Lloyd, may be found in lead smelters throughout the world, and also in many metallurgical works dealing with other ores, including those of iron. It is ordinarily used to desulphurize and agglomerate fine ores for subsequent smelting. Colonel Dwight's citation as James Douglas Medalist reads: "For his contributions to the art of smelting nonferrous ores; and particularly for his pioneer work in developing equipment and technique for sintering such ores and metallurgical products." The medal was awarded at the last Annual Meeting of the A.I.M.E. but unfortunately the medalist was unable to leave Florida at the time to receive it in person.

Jan 1, 1942

There are no data available of shipments until 1858, and then estimated, when railroad service became available. By reason of the iron made in the county, and the large amounts of salt, the tonnage used locally was quite large, and until 1860 these are estimated from the probable salt and iron production. After 1859 the tonnages shipped by rail are partly estimated from the total shipments of the Allegheny Valley Railroad from four counties. It is believed that the totals are below, rather than above, what the actual production was. While considerably larger for the same years than figures given by the Secretary of Internal Affairs and census reports, these data were always too low in those days, partly because of lack of facilities for gathering them, but more largely because of the strong prejudice existing in those days against furnishing such data to any governmental agencies.

Jan 1, 1942

By Foster Fraas

MOST commercial electrostatic separators utilize the electrical property of conductivity, but although based on the same principles, they are constructed in a variety of forms, a common one being the simple roll type. Some information obtained during an investigation of that type of separator, and which indirectly is applicable to other types, is presented here. NUMERICAL RELATIONSHIP In Fig. I material discharged from hopper 6 is fed onto grounded rotating roll 2. Electrode 3 is at a high electrical potential with respect to roll 2, and any conductive particle in contact with roll 2 therefore acquires an electrical charge of such polarity that, when present in the electrical field, the force on it is in the direction of electrode 3. A detailed description of the charging by conductance as utilized in electrostatic separators may be found in a previous publication.1 As a result of this force, the path of the projected particle is changed in increasing amounts in the direction toward region C as the magnitude of the charge is increased. With the dividing edge 4 the projected particles may be divided into two fractions -those in region C designated as "deflected" or " deflectant " and those in region B designated as "residue." [ ] When material is passed over the roll only once, a complete separation is seldom obtained, therefore most commercial separators contain several roll-separator units in series, and some practical machines use as many as 12. In this paper a "pass" means the passage of material over a single-roll unit. The procedure is to repass either residue B with a low potential on electrode 3 or deflectant C with a high potential on 3. Most electrostatic separations follow a flowsheet of roughing and cleaning either the concentrate or the tailing, on both. In a specific instance, a dry, heated mixture of wet cleaned chromite and garnet from an

Jan 1, 1942

During the latter part of the Civil War an income tax was placed upon coal and the production of coal in the various collection districts during the life of this tax is shown in the tabulation that follows. The counties that include coal deposits are shown for each district. No record exists now of the production by counties, but it is calculated here on the basis of tax collected. The table, of course, does not include any territory not under the control of the northern armies, and not all of that in some cases.

Jan 1, 1942

By Morris Muskat

ANALYTICAL calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/3 in., and to approximately one half for a perforation radius of 1/4 in,, regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings.

Jan 1, 1942

By B. K. Miller, R. S. Bradley

The principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. Most of the semiplastic‡ fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north centra! Ozark district. High-alumina diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semi-plastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1942

Jan 1, 1942

A USEFUL and very ingenious idea was surely that of the inventor of AN a short way of extracting gold and silver from the sweepings of all those arts that handle them as well as every particle that smelters of ores might have left in the slags, and also that in some ores themselves. This is done without using great labor in smelting but by the sole means and virtue of mercury. To do this, first make a large bricked pan of stone or wood and arrange a millstone inside which rotates in the hollow of this pan like that of a flour mill. In the hollow of the pan put some of your material containing gold after it has been crushed well in a mortar and then washed and dried. Grind it in the said mill, moistening it meanwhile with vinegar or water in which sublimate, verdigris, and common salt have been dissolved. Then enough mercury to cover these materials is poured over them. They are agitated inside for an hour or two, by turning the mill either by hand or with a horse, depending on the device that you have arranged. Remember that the more the mercury and the material are rubbed together in the mill the more it can be believed that the mercury absorbs the substance that the materials contain. Finally, thus prepared, the mercury is separated from the earthiness with a sieve or by washing and thus the mercury is retrieved. Then, make it rise with a little cucurbit or pass it through a purse and there will remain at the bottom the gold, silver,. copper, or whatever metal you placed in the pan under the millstone to be ground. Wishing to know this secret, I gave to the one who taught it to me a ring with a diamond worth twenty-five ducats, and I also pledged myself to give him the eighth part of whatever profit I should gain from this

Jan 1, 1942

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942

Data about production are very meager. In this county from the earliest days until after the Civil War, the amount of coal used locally greatly exceeded that shipped on account of the iron produced; for many years the furnaces used raw coal for melting the ore. In 1846 it was stated that in this county one ton of iron required three tons of iron ore and three tons of local coal used raw.1 In 1864, eleven furnaces in Pennsylvania using 102,230 tons of raw coal produced 44,671 tons of iron, or 2.3 tons raw coal per ton of pig iron .2 This was probably as good a record as was made, as nearly all furnaces changed to coke some years later. Neither of these figures include the coal used for steam and other purposes around an iron plant. The Beaver and Erie Canal was opened in 1845 and the shipments shown from then to 1865, inclusive, are of coal received by the canal at Erie, and do not include any used at local points along the canal. From the completion of the Erie and Pittsburgh Railroad in 1864 the tonnage shipped by canal decreased. rapidly, and, while the canal shipments after 1864 are supposed to be those received at Erie by canal only, they may include some rail tonnages. Tonnages on Erie and Pittsburgh Railroad may, and probably do, include some used locally; those on the Jamestown & Franklin Railroad do not. It is likely that both canal and Erie and Pittsburgh Railroad figures include some coal originating in Lawrence County, and possibly a little from Beaver County. These tonnages are not duplicated in the data for either of the other counties. Not all of the railroad reports can be found now.

Jan 1, 1942