Search Documents

By Lyman Taylor, Alexander R. Troiano

STUDIES of the transformation of austenite at constant subcritical temperatures have been numerous since the work of Davenport and Bain.1 Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of austenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. EXPERIMENTAL PROCEDURE Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8-in. round bars. Bars were softened at 650° to 700°C. before the specimens were cut. [ ] Metallographic Method Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examination of partially reacted specimens. Thees specimens were approximately ½ by ¼ by 1/8 in. in size. Specimens of the 9 per cent Cr steel were held 10 to 12 hr. at 1200° to I225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 ½ hr. at 1200°C. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. No. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed in Table I. X-ray Methods Constituents were identified and martensite axial ratios determined from Debye

Jan 1, 1945

By James Terry Duce

The gross production on the Island of Sahreirl during 1944 was approximately 6,700,000 U. S. bbl. No additional wells were drilled in the field during the year, but a number that were plugged off during the critical days of the war were brought back on production. This work is continuing. The construction of the extension of the refining plant was continued during the year and the new crude still was started in November. In Arabia, the production for the year 1940 was 5,074,838 U. S. bbl. Four wells were completed in Dammam field and all were commercial producers. Production for 1941 was 4,310,110 U. S. bbl. Seven more commercial producing wells were completed in Dammam field, and Well No. I at Abqaiq was complcted at 6180 ft. and was also a commercial producer. In 1942 production was 4,530,492 U. S. bbl. Abqaiq No. 2 was drilled to 5785 ft. but was left standing because of mechanical difficulty. The 1943 production was 4,868,- 184 with one well drilled, Abqaiq No. 3 completed at 6488 ft. and a commercial producer. Total production in Arabia for the year 1944 was around 7,800,000 U. S. bbl. and at the close of the year was running at approximately 40,000 bbl. per day. The small refinery, built in 1939, at Ras Tanura was in operation in the fall and a new refinery is being constructed. Only three wells were completed during the year—the El Jauf well in Northern Arabia (completed at 10,974 ft.) which did not bring in commercial production and Wells No. 4 (completed at 6270 ft.) and No. 5 at Abqaiq (completed at 6751 ft.), which were brought in as substantial commercial producers. Production for the year was entirely from the Dammam field. In this field, some of the wells that had been plugged off early in the war were brought back in production and this work is continuing. At the close of the year, one well was drilling in the Abqaiq field and an additional well was drilling at Qatif, the latter being a wildcat. Neither of the wells in question had reached producing horizons on the first of January.

Jan 1, 1945

By Howard C. Dunkle

Various factors can affect the quality of BIII2 and BIII3 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. Significance of Steel Manganese, Mixer Silicon and Steel Sulphur as Quality Factors In order to obtain the highest grade of material it is necessary to control many factors—not just one or two, as operators

Jan 1, 1945

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945

By James A. Barr

THE writer's first experience with flotation was during World War I, in the beneficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added. The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals Separation mechanical flotation machines were used in another graphite mill. Pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"[t] using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the Phosphate Recovery Corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for beneficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., subaeration types, with weir control of pulp between cells. The sand bleeders were very small-about 1 ¼ -in. diameter. As the feed contained 15 to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. I and details of the cascade construction in Fig. 2. The cascade installation in plant No. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1945

By W. J. Kroll

Despite the fact that barium minerals are plentiful and widely distributed in nature, this element is one that we do not yet know how to prepare cheaply in metallic form. This is due to its chemical activity, as evidenced by its great affinity for fluorine, chlorine, oxygen, nitrogen, hydrogen, and sulfur. Furthermore, it forms a very stable subchloride and subfluoride, which prevents isolation of the metal by fusion electrolysis from a halide bath. A good survey of the metallurgy of barium calcium, arid strontium has been made recently in Light Metals (54,55).3/ Metallic magnesium (46), calcium (83), barium, and strontium (27) reduce each other's oxides. Proof of this can be found in the activation of BaO after reduction with Mg, which leads to the formation of so-called "Maquenne" mixtures (58) used for absorbing gases. However, it is impossible to extract the reduced metal- from the residue, a fact that Guntz (25) attributed to the formation of barium suboxide. There is no necessity for presuming the formation of such a compound, as it has boon established that in the reduction there is always formed an alloy of the alkaline-earth metal with the magnesium, which is capable of producing hydrogen when brought into contact with water. The reduction of alkaline earth-metal oxides with aluminum was observed by Mallet (57) in 1877, but recent investigations have shown that the end product of the reaction is an alloy of aluminum with the alkaline earth metal (1,2). Silicon also has been suggested as a reducing agent, and the results obtained are the same (84,85).

Jan 1, 1945

By Rex W. Woods, Morris Muskat

A leastmsquare analysis procedure has been developed and applied for the study of the deviations in estimations of oil in place as given by the material-balance equations. The data used were those obtained from field observations on the Jones sand in the Schuler pool, Arkansas, and the Monroe dolomite in the Reed City pool, Michigan. Possible effects of water intrusion were taken into account by expressing the cumulative water influx in terms of various functions previously proposed in the literature. Formulas were developed and values calculated for the minimum deviations and minimal percentage deviations in the calculated volumes of oil in place from the average values, as could be obtained by suitable choice of the water encroachment and initial gas-cap volume parameters. The results show that the fluctuations in these calculated volumes are very insensitive to the values chosen for the rate of water intrusion and initial gas-cap volume, and hence cannot be safely used in discriminating between spurious values for these parameters and such as actually pertain to the producing reservoirs. Moreover, the exact form of the water-intrusion function seems to have but little effect on the fluctuations in the computed oil in place. Accordingly, it is concluded that the material-balance method does not of itself provide a satisfactory criterion for determining the basic physical unknowns of producing reservoirs or in making conclusive decisions regarding the production mechanism, unless independently established geological control data are available for eliminating unreasonable values for the reservoir parameters, even though they may still satisfy the material-balance formulas. If, however, from core or logging data the initial oil in place and the gas-cap volume can be established in advance, the material-balance formulas can be inverted to find the water intrusion. Moreover, by determining by such calculations the water-intrusion coefficient, the iuture production performance can then be predicted by the aid of the materiaI-balance formulas for specified operating conditions. This type of application may be of particular value in predicting the results of Pressure-maintenance operations. Introduction The evaluation of the forces acting upon an oil reservoir is a problem of considerable interest to the operator as an aid in determining the proper method of operation for the reservoir to obtain an optimum recovery of oil. In many pools, the nature and magnitude of the forces acting upon the reservoir remain unknown until an appreciable amount of ultimate recovery is obtained. To be of value to the operator, a reliable interpretation of reservoir performance should be available in the early life of the pool to permit an optimum plan of operation. Progress has been made in an understanding of reservoir behavior and the importance of the different factors involved. The material-balance method of estimating oil in place has been proposed as a tool in analyzing reservoir-performance problems.l The solution of such problems by this method ordinarily involves two or more unknown values relating to the nature of the reservoir, and the results

Jan 1, 1945

By C. W. Phillips, R. S. Busk

With most cast metals the grain size may vary within wide limits, depending upon the conditions at the moment of freezing. These conditions are subject to control in magnesium-base alloys, by proper melting and superheating techniques, enabling production of quite uniform and fine-grained castings, almost independent of section thickness. However, such variations of grain size as do exist, in common with all metals, are reflected in corresponding changes in mechanical properties. It is the intent of this paper to present data giving the relationship between grain size and mechanical properties. Data are also included on the combined effects of grain size and micro-porosity. In addition, a short discussion of factors influencing the grain size of sand castings is included. Measurement OF Grain Size By grain size is meant the statistical distribution of volumes occupied by the individual crystallites in a metal section. Since this is almost always impossible of direct measurement, several methods of estimating and expressing the size have been evolved. Most exact methods make use of the microscope. This involves study of a single plane cut at random through the metal. What is seen in the microscopc are polygons, each the cross section of a grain. The diameters or areas of these polygons are then measured and the grain size is expressed as an average diameter, number of grains per unit area, average area per grain, or, rarely, average volume per grain. Rutherford, Abom, and Bain3 have discussed extensively the errors involved when using a plane section to estimate volume. They clearly point out that the tendency is to underestimate the true grain size because of the nature of the measurcment. The A.S.T.M. recommends that measurement be made by comparison with a standard chart, by means of Jeffries' planimetric method4 or Heyn's intercept method. The Society recommends that the notation be in terms of the number of grains per unit area (as is the grain-size number used for steel) or as an average diameter, expressed in inches or millimeters (as for copper and brass). The method of measurement used for this study was comparison with a standard chart, which has been described by P. F. George.5 The chart was constructed by photographing at Ioo diameters a uniform specimen with an average grain diameter of 0.003 in. The average diameter of this specimen was determined by numerous measurements, using both the Jeffries and Heyn methods. The other grain sizes were then obtained by appropriate enlargemcnt of the master sample. Careful comparison of the chart method with other methods on identical samples indicates that though the differences be-

Jan 1, 1945

By Lowell B. Moon

Regardless of how a mineral deposit in first discovered or by whom, any mining enterprise based upon it must pass through a preliminary stage of exploration. The common understanding of ?exploration? among mining engineers is well-expressed by Jackson and Knaebel:3/ Exploration work ranges from that performed by the individual prospector employing only the simplest tool, and equipment to elaborate campaigns involving the expenditure of largo stuns of money end the use of churn- car diamond-drilling equipment, large test-pitting crews, or sometimes a regular mining organization. In any event, the object is to determine as accurately as possible, with the funds available, the size, shape, and other characteristics of the ore bodies and their average value or grade.

Jan 1, 1945

By L. H. Bergmann

THE blasting practices described are fairly representative of those employed in the coal mines of Eastern Canada. As such, they may be of interest to Western Canadian coal mine operators. The treatment of the subject is general, no attempt being made to discuss blasting operations at any particular coal mine in detail. All the mines dealt with are mining bituminous coal and are classified under the Coal Mines Regulation Act of the Province of Nova Scotia as 'closed light' mines. As such, they are required to use only 'permitted' explosives and to apply them in a 'permitted' manner, except where authority is given by the Mines Department to do otherwise.

Jan 1, 1945

By Edward Pesout

THE McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.1 EARLY PULVERIZING PLANT Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a finer product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. [ ] It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. 0-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1945

By G. S. Hume

During the war years the drilling activity in Canada has been steadily increasing and still further increase is expected in 1945. The production of oil, which in the past has come largely from the Turner Valley field in Alberta, shows a decline since 1942, the peak year. New discoveries made in 1944, however, give promise of replacing the decrease from Turner Valley where the crude-oil production in 1944 was nearly 1,800,000 bbl. less than in 1942, but with an increase of 145,000 bbl. in natural gasoline, a product of great value to the war effort. A very considerable part of the decline in Alberta has been offset by new production of more than a million barrels in 1944 from the Norman Wells field, in the Mackenzie River area of the Northwest Territories. It should not be forgotten, however, that this is largely due to the Canol development, a war project, the future of which is dependent on many factors not connected with an ordinary commercial operation. The year 1944 has been the best in new discoveries in Alberta for all time. The discovery of a new deep field at Jumping-pound, 20 miles west of Calgary, with the hopc of a type of product similar to that of Turner Valley is the culmination of many years of effort to interpret the subsurface structures in relation to the complicated surface foothills faulting and folding. In this case the subsurface structure on the Paleozoic limestone was inferred from geological investigations but precisely defined by seismograph. In addition to Jumpingpound the discovery of oil of 34.5 gravity at a depth of less than 5000 ft, in the Devonian of the Plains at Princess, 125 miles east of Calgary, is of great significance since this is the first substantial production from the Devonian in Alberta, although previously some oil had been obtained at two places from the Devonian in the foothills. The effect of this discovery is already apparent in the number of wells now drilling to the Devonian in the southern Plains. In southern Alberta a new producing area has been found in a Lower Cretaceous sand at Barnwell, a few miles west of Taber. Also, at Conrad, 20 miles southeast of Taber, an important new discovery has been made at a depth of about 3000 ft. in a sand in Jurassic shales, in a strali-graphic trap on the northeast flank of the Sweetgrass arch. In northeast Central Alberta an important extension has been found in the Lloydminster area, where only a few wells have so far been drilled. A new well 3 1/2 miles south of the previous producers found a coarser sand at the productive horizon and as a result will have an increased daily yield. At Blackfoot, 9 miles west of Lloydrninster, a new producing area in the Lower Cretaceous may have been discovered at a depth of 2004 ft. At the end of 1944 the well was being tested. Forty-four unsuccessful wildcat wells were drilled in Alberta in 1944. The decline of Turner Valley, the major producing field, was anticipated at the beginning of the war and in an effort to offset this and encourage new development the Dominion Government put into force tax concessions and other measures that,

Jan 1, 1945

By Cleveland Meeting

Jan 1, 1945

By F. H. Wilson, R. M. Brick

With the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made. to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45' to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the caring behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass Earing BehavioR oF Brass Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (II3)[I12] This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;' Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photo-grams for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By C. J. Bonnecarrere, P. A. Jr. Bloomer, J. Hunter

Since 1941 not more than 15 per cent of aii wildcat wells drilled in Louisiana have been successful. This figure is not too discouraging, especially in view of the fact that during the same period approximately 80 per cent of all wells (average 701 wells per year) drilled in or adjoining producing areas were successfully completed. However, a somewhat discouraging aspect concerning Louisiana's wildcat completions is that in 1942 only 12 out of 20 fields found were oil fields; in 1943, only 13 out of 24; and in 1944, only 8 out of 21. This means that an operator has less than a 50:50 chance of finding an oil field. In other words, it is more likely that he will find a gas-condensate field. This fact has become increasingly evident as the data for each year are compiled and compared. Yet, strangely enough, operators are reluctant to accept this fact and plan accordingly. Certainly they cannot continue to search for oil fields and, for the most part, end with shut-in gas-condensate wells. The reason for shutting in is that there is no immediate and satisfactory market for all the gas being discovered. The solution, and it is a very satisfactory one, as experience in Louisiana has already demonstrated, is cycling. The advantages of this type of operation of gas-condensate fields, especially where the entire field is pooled and unitized, should be self-evident. These advantages will become increasingly more important, especially now that legislatures, regulatory bodies, royalty owners, and others are beginning to realize that "reasonable development" in a field is not indicated by the number of wells completed, but rather by the method of development. To complete a great many wells that can produce at only, partial capacity is waste. Producing hydrocarbons from these wells and not subjecting them to processing by surface operations, in order to recover all liquefiable hydrocarbons, is waste. Permitting bottom-hole pressures to drop or gas-oil ratios to increase because of excessive production is waste. Loss of leases and of wells because of inability to produce or to meet lease obligations is waste. Therefore, it is becoming increasingly apparent that a reservoir entirely pooled and unitized with a minimum number of completions, but over which there is exerted careful control so as to provide maximum recovery and the processing of all hydrocarbons brought to the surface, is the only logical and reasonable method of developing a gas-condensate field. Oil Production Twenty-one new fields, including three rediscoveries, were found during 1944. Three of these new discoveries—Delhi in northeast Louisiana, Good Hope in southeast Louisiana, and West Tepetate in southwest Louisiana—should add considerably to Louisiana's oil reserves. The other discoveries were either gas condensate or of apparently little consequence. State-wide productioll for 1944 was 1366 million barrels of crude oil and condensate; amounting to about 8.1 per cent of the

Jan 1, 1945

By E. Lee Cameron

The old mine workings on four barite-fluorite veins of the Lake Ainslie district, Nova Scotia, were opened recently and channel sampled. The samples were then forwarded to the Ore Dressing Laboratories, Bureau of Mines, Ottawa, for chemical analyses. Following the analyses, the sample rejects were combined to form bulk samples, representing ore from each vein, for small-scale batch test work. Tonnage samples from the veins, for pilot mill testing, were submitted when requested by the Bureau. The results of the analyses on the channel samples showed that there are two grades of ore in the di strict, represented, for test purposes, by the Trout River vein and Johnson vein ores. Small-scale and pilot-plant test work was undertaken on both these ores. The Trout River ore is amenable co concentration but, because of the high-barite-co-fluorite-co-calcite ratio, a fluorite concentrate was not obtainable from the Johnson vein ore as received. However, Johnson ore blended in a 1 :1 ratio with Trout River ore gave a mill feed that was readily concentrated. The test work on these ores showed that the following concentrates are obtainable : (a) A barite concentrate, with a recovery of 85 to 95 per cent of the available barite, analysing 93 co 96 per cent BaS04, 4 co 6 per cent CaF,, and 0.5 co 2 per cent CaCO3. (b) A fluorite concentrate, with a recovery of 80 co 85 per cent of the available fluorite, analysing 94 to 97 per cent CaF, , 1 to 3 per cent BaSO., and 1 to 3 per cent CaCO3

Jan 1, 1945

By D. J. McAdam

As shown in three recent papers by the author, in two papers by McAdam and Mebs, and in a paper by McAdam, Mebs, and Geil," the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stressest as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strength1 nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. rb and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses. with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. ib shows stress combinations with Sz equal to The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. u shows stress combinations with S2 equal to St. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-II In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1945

By L. D. Jaffe, J. H. Hollomon

The effect of tempering temperature and time upon the properties of quenched steel is clearly a subject of great practical importance, as well as of considerable theoretical interest. It would be very desirable to be able to predict the properties of a quenched steel when given any selected tempering cycle, with a minimum of experimental work upon that heat or even type of steel. Two problems are involved: one consists of relating the structure obtained to the physical properties, and will not be discussed here; the other, with which this paper deals, involves the relations of time, temperature and composition with the structure obtained 011 tempering. Indentation hardness is perhaps the most convenient quantitative measure of the tempered structure, or of what might be called the "degree of tempering." Undoubtedly, it is not an exact measure, and in some cases (as when temper-brittleness occurs) pieces of the same quenched and tempered steel may have widely differing properties at the same hardness. However, hardness has the advantage of being simple to determine and is certainly the most widely used indication of the degree of tempering. Moreover, for fully quenched steels that are not temper-brittle and do not contain retained austenite when quenched, it appears that, in general, if the hardness of the steel is the same, the tensile and impact properties will also be identical, whether a high or a low tempering temperature is used. The tempering charts available in the metallurgical literature usually give the hardness as a function of tempering temperature for only one tempering time. However, in practice, tempering times frequently vary, and a method of converting tempering curves for one time to tempering curves for some other time would be very valuable. It is also advantageous, in determining the tempering treatment necessary for a given part, not to have to temper samples at several temperatures for the time used for the commercial tempering operation. A more satisfactory procedure would be to employ times of the order of 10 to 30 min., rather than 5 or 10 hr., and if possible to use only one temperature. Furthermore, it is frequently desirable, for reasons such as temper-brittleness,* to obtain a given hardness with short times at relatively high temperatures, and it would be convenient to be able to compute without tests the time required to produce this hardness. Remarkably few quantitative studies of the hardness of quenched steel tempered over wide ranges of temperature and time

Jan 1, 1945

By Albert J. McIntosh

With petroleum consumption declining temporarily after V-J day, the oil industry is urged to use this period as a kind of stopgap to rebuild its war-depleted inventories and help cushion the effect of this decline on producers and refiners. Higher inventories should be reestablished, since recent experiences have indicated that, by and large, the present inventories of crude oil are too low even with the tremendous current production available. The following analysis indicates that inventory levels could be built up to about 490,000,000 bbl. by the end of 1947, an increase of about 40,000,000 bbl. over the reported stock estimated for the war's end. If at the end of the war the military have some 20,000,000 bbl. on hand, this inventory will either be resold to the industry or certain demands that have been assumed to be met by industry will be supplied out of these military stocks, which would leave about 20,000,000 bbl. (net) to be built up from current production. For stock rebuilding the industry could use 10,000,000 bbl. of crude plus 10,00,000 bbl. of products, totaling 20,000,000 bbl. If this were spread over a year, this would mean 55,000 bbl. a day. By analyzing the average inventories held in a year with the total quantity of goods handled during the year, the following study and tables indicate how far the inventories should increase in the immediate postwar period. Introduction For the period immediately following V-J day, most of the petroleum economists have forecast a considerable decline in the total consumption of petroleum and its products in the United States. This will be caused by the elimination of most of the military demands and the inability of civilians to immediately replace automobiles, burners, etc., and thus increase their requirements to make up for the military decline. When the automobile industry has been back on full production for two or three years, civilians will be able to consume much larger quantities of gasoline. Delay in the manufacture of new oil burners and the time it takes to construct new homes, adds up to the same story for distillate fuels. In reviewing this outlook, the question has arisen whether the petroleum industry should not use this period of lower consumption as a kind of stopgap to rebuild its war-depleted inveritories and help cushion the effect on producers and refiners of this sudden drop in requirements. Some persons have indicated that hundreds of thousands of barrels a day could be used for this purpose extending over a year or more. Refineries will be in existence, which could run over 5,000,000 bbl. of crude oil a day and crude-oil production might be running 600,000 to 700,000 bbl. a day above the demands now forecast for the period after V-J day. Reasons for. Making Inventories In order to plan intelligently for this period, the petroleum industry should determine the needs for the establishment of higher inventories for crude and petroleum products than have been carried during the war. The reasons for trying to make such a determination are as follows:

Jan 1, 1945

By Roland D. Parks

CORUNDUM, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to our allies. Optical elements of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mohs' scale index of o, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent of this paper to deal only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. ORE PRODUCTION AND CONSUMPTION For the past two decades, South Africa has been the world's sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world's principal consumer of corundum ore; imports for the period 1934 through 1940 averaging 3000 short tons per year. The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the United States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918. Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912,

Jan 1, 1945