Search Documents

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

By John J. Collins

Page Purpose and scope..................... 521 Core sampling......................... 521 Sludge sampling....................... 527 Combining core and sludge assays ...... 533 Deviation and surveying of drill holes. . . . 537 Conclusions........................... 544 Acknowledgments...................... 545 Bibliography.......................... 545 Purpose and Scope The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described,25,26,31,32,50,65 but more informa- tion is needed on the results shown by actual mining operations. Core Sampling The accuracy of diamond-drill-hole Sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says; in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change; often indicated by a color change in the sludge water, should be a a for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By Martin C. H, Met B

INDEX OF CONTENTS:1. Introduction, Explanatory; and Reasons for Coal Cleaning.2. Principles on which Coal Cleaning is based.3. Location of Broken Hill Proprietary Co. Ltd. Plant.4. Description of Processes Selected Barvoys Bath Process; Barvoys Medium Preparation and Treatment; Static Dry Cleaning Plant.5. Detailed Description of Plant.6. Typical Results of Cleaning Operations.INTRODUCTION, EXPLANATORY, AND REASONS FOR COALCLEANING:The Institute proceedings have not previously published any matter on coal cleaning and the reasons thereof; in consequence it has been deemed advisable to allot a part of this paper to explanatory matter, prior to entering into a detailed explanation and description of the Newcastle plant.At the outset it would be as well to consider briefly the kinds of materials from which coal has originated. All coals represent some stage in the decomposition and transformation of vegetable matter laid down in prehistoric times, the vegetable matter undergoing numerous geological changes, such as submergence, overlaying by sediment, with subsequent pressure and re-elevation; these processes may...

Jan 1, 1946

THE Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated: 1924 What is Steel? By Albert Sauveur. 1925 Austenite and Austenitic Steels. By John A. Mathews. 1926 Twenty-five Years of Metallography. By William Campbell. 1927 Alloy Steels. By Bradley Stoughton. 1928 Significance of the Simple Steel Analysis. By Henry D. Hibbard. 1929 Studies of Hadfield's Manganese Steel with the High-power Microscope. By John Howe Hall. 1930 The Future of the American Ironand Steel Industry. By Zay Jeffries. 1931 On the Art of Metallography. By Francis F. Lucas. 1932 On the Rates of Reactions in Solid Steel. By Edgar C. Bain. 1933 Steelmaking, Processes. By . George B. Waterhouse.

Jan 1, 1946

[NORTH AMERICA UNITED STATES ALABAMA America.-Dyar, 0. C. Anniston.-Klugh, B. 0. Ashland.-Pallister, H. D. Auburn.-*Poor, R. S. Bessemer.-Creveling, J. 0. Lindstrom, W. A. McKenzie, W. 0. Mitchell, F. R. Birmingham.-Abbott, C. E. Aldrich, T. H., Jr. Armstrong, 0. R. Beard, A. H. Benjamin, F. S. Blackburn, E. 0. Blair, A. J. Blair, 0. S. Blair. H. W.]

Jan 1, 1946

By R. D. Longyear

[Some Problems Involved in the Interpretation of Diamond-drill-hole Sampling and Surve ing (paper by J. J. Collins, Mining Tech., Jan. 1946). ............... I Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota (paper by R. H. B. Jones, Mining Tech., July 1946) ................... 2] DISCUSSION R. D. LONGYEAR.*-Mr. Collins is to be commended very highly for the brief summary he has made of the currently used methods of taking diamond-drill sludge samples and the principles involved in evaluating the results. This paper should stimulate further discussion and research on this vitally important problem. It is particularly imperative that geologists and engineers know when assay results on sludge recovery can be accepted quantitatively and when they must be considered only qualitatively. In most cases where the sludge recovery is less than 95 per cent or more than 125 per cent, it is safest to consider the assays as of qualitative value only. Certain cases, however, are known where a relatively small proportion of the sludge sampling will give a reasonably accurate measure of the value of the total sample. One such case is ore in which the valuable mineral is of approximately the same specific gravity as the waste mineral, such as chalcopyrite in a massive pyrite body. The essential point is to determine the degree of accuracy of sludge sampling in any given drilling project and to weigh the results accordingly. It should be emphasized, however, that sludge sampling can be made reliable in many localities where careless practice produces unreliable results. In many instances, it is desirable to empty the core barrel in the core shack instead of at the drill, so that the engineer can examine the core as it first comes from the core barrel. It should be pointed out, however, that the drill * E. J. Longyear Co., Minneapolis, Minnesota. runner should be permitted to study the core to guide his future drilling. It is hoped that with the return of more normal conditions after the war geologists, engineers, contractors, and manufacturers will be able to carry on more research along the lines of improved core-barrel design and drilling technique with the objective of increasing core recovery so as to eliminate as far as possible the necessity of relying upon sludge samples. H. M. ROBERTS.*-Whoever in the future will have to do with the search for ore bodies and their exploration will have frequent occasion to refer to the clear and comprehensive summary on diamond-drilling methods by John Collins. His review of the experience of the last 40 years in this technique is invaluable. As Dr. L. D. Ricketts wrote in 1932, "The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be intrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reinforcing detail that clothes and tends to disguise them."[t] Ricketts went on to say that since the beginning of the century there has been much

Jan 1, 1946

By A. F. Brock

The cut-and-fill mining methods in use in the mines of The International Nickel Company of Canada Limited, at Falconbridge Nickel Mines Limited, in the Sudbury District, and at McIntyre Porcupine Mines Limited in the Porcupine District, are typical of the general cut-and-fill practice in both the base-metal mines and the gold mines in the Province of Ontario. The following pages describe the methods in use. HORIZONTAL CUT-AND-FILL STOPING Horizontal cut-and-fill stoping, as practiced in the mines of The International Nickel Company of Canada Limited, falls into two main classifications: (I) transverse cut-and-fill stoping, where ground conditions or wide ore bodies make it necessary to establish narrow stopes and pillars across the width of the ore body; (2) longitudinal cut-and-fill stoping where ore body widths and ground conditions allow safe mining of the full width of the ore body. Transverse Cut-and-fill StopiNg General Stoping Layouts Stope and Pillar Widths.—For transverse stoping, experience has indicated that narrow stopes and pillars, 27 ft. 6 in and 22 ft., respectively, are most satisfactory. These width are multiples of 5 ft. 6 in., which is the center to center dimension of a standard square set. Thus any stope, or block of stopes, can be readily converted from cut-and-fill to square set-and-fill if ground conditions should warrant such a change. Formerly, pillars were established 16 ft. 6 in. wide, the equivalent of the width of three square sets, with the intention of extracting the pillars by mining an overhand slice one set wide and an underhand slice two sets wide. However, subsequent experience proved that a two-set overhand slice is so much more efficiently mined than a one-set slice, and 22-ft. pillars have been made standard. Chutes.—The stope chutes are established on the longitudinal center line of the stopes and are spaced at 22-ft. centers from footwall to hanging wall. The footwall chute is usually from 5 to 10 it. from the footwall of the stope. It is offset where necessary at an angle of 52° and vertical chutes are carried from the offset at 22-ft. centers. In sections of the ore body where a flat hanging wall would cut off hanging-wall chutes within a few cuts of the sill, it has proved to be more economical to use temporary chutes or slushers, or both, for these first few cuts, rather than to el permanent chutes at the hanging wall.

Jan 1, 1946

By Ernest N. Patty, Sherwin F. Kelly

The present case history deals with the examination of an almost forgotten nickel prospect, near Winesap, Chelan County, Washington. Although the final results yielded no ore body of commercial importance, the integration of surface and underground exploration, geophysical survey and diamond drilling endow the story with interest. The program is significant because it is illustrative of how the most disappointing expenditures in mining exploration, the "not-finding" costs, could have been reduced had geophysical methods been applied at an appropriate stage in the prospecting work. The Chelan nickel deposit was discovered about 1900, on a sage-brush-covered hillside with a southerly slope, adjacent to Winesap Canyon; the paved highway now extending from Wenatchee northward, up the Columbia River and into Okanogan Valley, is only a mile away. After the deposit was found, three short prospect tunnels were driven into it, and the prospect then remained dormant for 40 years. No. x tunnel was 80 ft. long, running north into the hillside. For the first 35 ft. this adit exposed a typical, iron-stained gossan with streaks and stains of malachite, and small seams of water-soluble nickel sulphate. Beyond this, it encountered a relatively fresh peridotite, well mineralized with blebs of pentlandite. Systematic sampling yielded an average assay of 1.5 per cent nickel and 0.3 per cent copper. Down the hillside to the south and 35 ft. lower in elevation, No. 2 tunnel was driven under No. I and in the same direction, traversing 50 ft. of gneiss before it reached the peridotite. At this point the latter formation showed only scattered blebs of sulphides, not of commercial grade. To the west, on the same contour line as No. I tunnel, and 800 ft. around the hillside from it, No. 3 tunnel was driven 50 ft. into the hill to explore a strong gossan outcrop that assayed 0.5 per cent nickel (Fig. I). From the geological exposures on the hillside and in the tunnels, it appears that the main mass of the hill is formed of an ancient and altered gneiss complex. Into this, a sill-like injection of amphibolite (altered peridotite) was intruded, which, at least in some places, contains commercial quantities of nickel sulphide. Its structure is obscure, but it appears to dip into the hill at an angle of about 15°. In the vicinity of No. 3 tunnel a large dike of quartz diorite cuts the peridotite or amphibolite; about 140 ft. north of the portal of the tunnel, a dike of andesite 00 ft. wide cuts boldly up the hillside to break the continuity of the peridotite in that direction. The geological evidence available was not adequate to decide whether the peridotite forms a continuous sill, or occurs as isolated bodies in the gneiss. Not all of this peridotite carries commercial amounts of pentlandite, but if the mineral-

Jan 1, 1946

By John Wulff, Richard P. Seelig

THE importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by sub- sequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be con- trolled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper. In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshin1 on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin1 and Rakovski.2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,1 based on a hydro- dynamic analogy, however, leads to but another way of plotting density and pres- sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. DENSITY GRADIENTS IN COMPACTS The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

[E. E. SCHUMACHER, Chairman ARTHUR PHILLIPS, Past-Chairman L W. KEMPF, Senior Vice-Chairman E. A. ANDERSON, Vice-Chairman H. A. MALONEY, Treasurer FRANK T..SISCO. Secretary 29 West 39th Street, New York 18, N. Y.]

Jan 1, 1946

By R. F. Marande, R. S. Busk

THE magnesium-aluminum-zinc system contains most of the magnesium-base alloys used commercially, although in practice the ternary, alloys are usually modified by the addition of a small amount [ ] of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the object of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.1 [ ] All alloys reported were made in 15-lb. melts, superheated to 1700°F. for 15 min., cooled to 1400°F. and poured in sand molds. The test bars produced had a ½ in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. CONSTITUTIONAL DATA Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By Coolbaugh, Franklin

CRUSHING of Climax mine-run ore is carried out in two plants: No. 1 plant (flowsheet in Fig. 1) has a capacity of approximately 5000 tons per day. It is used as a stand-by except when maximum production is required. No. 2 plant (Fig. 2) has a top capacity of approximately 17,000 tons per day. The No. 2 crusher is more efficient to operate on reduced tonnages regardless of the wide variation in peak capacities. The system of crushing is similar in both plants: Mine ore, of a size which can be drawn through 48 by 96-in. slusher openings underground, is dumped into the crusher bins from ten-ton mine cars and fed into 48 by 60-in. Buchanan jaw crushers by means of chutes and Ross chain feeders. The jaw crushers are set to discharge at approximately 9-in. size. Jaw crusher discharge is conveyed to 7-ft. Symons standard cone crushers where it is broken to minus-2-in. size,

Jan 1, 1946

By George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond county, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1914, the derrick spans, 2,000 feet or more long, became unwieldy. To overcome this, and also to eliminate hand labour as much as possible, steam shovels and railway haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type.

Jan 1, 1946

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By E. A. Gulbransen, J. W. Hickman

ONE of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film A comprehensive program has been undertaken to study these phenomena This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C Before the introduction of the electron diffraction technique, it «as necessary to use either direct chemical analyses or X-ray diffraction analyses to determine the nature of the oxide film formed on the metal or alloy Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry In special cases the information obtained may be identical, but in general both view-points are necessary Much of, the early work was carried out on the oxidation of bulk samples where thick films were obtained The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses Although much useful information has been obtained in this manner, little could be learned about the character of the protective oxides during the period when the films were actually protective Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective LITERATURE The oxidation of iron has been extensively investigated by X-ray and electron diffraction Jackson and Quarrell1 found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe304, between 515° and 900°C the stable film was FeO Above the upper change point of iron the oxide was found to be Fe304 prom 400° to 515°C , FeO, Fe304 or a mixture of the two oxides was found Recrystallization of the air-formed film below 400° and above 900°C led to the formation of Fe304 In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described

Jan 1, 1946

[ARIZONA Established July 10, 1915 CHARLES R. KUZELL, Chairman GILBERT C. DAVIS, First Vice-Chairman ALBERT MENDELSOHN, Second Vice-Chairman MORRIS G. FOWLER, Secretary-Treasurer Phelps Dodge Corporation, Douglas, Ariz. LYLE M. BARKER P. D. I. HONEYMAN A. T. BARR H. M. LAVENDER T. G. CHAPMAN WALTER C. LAWSON GEORGE M. COLVOCORESSES W. H. LOERPABEL EDWIN H. CRABTREE, JR. CARL F. MILLS WALTER I. GARMS P. M. MOSIER WESLEY P. Goss J. A. RICHARDS 11. C. HENRIE JOSEPH A. WILCOX C. F. WILLIS]

Jan 1, 1946

Jan 1, 1946

TO THE. BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following committees: Membership, Admissions, Papers and Publications, Mining and Metallury (Magazine), and Library. In this review of the year by the Secretary reference frequently will be made to the "Paul" Committee and to the "hotter" Committee. The first is the special committee on Divisional Relationships and the second the special Committee on Ways and Means. These two important committees, appointed by President Harvey S. Mudd under authorization of the Board of Directors on March 21, 1945, were composed as follows:

Jan 1, 1946

[ ]

Jan 1, 1946

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946