Search Documents

By John Taber, Robert D. O'Brien

"INTRODUCTION The Bozeman corundum deposit was first examined in May 1944 by an engineer of the Bureau of Mines. In August 1944, the property was re-examined because of a sharply increased war demand for corundum. A small program of trench exploring was undertaken after the second examination. The work was started in October 1944 and was completed in December 1944. This report presents the essential data obtained by the exploratory work.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that, they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The field work on the Bear Trap project was supervised by E. W. Newman, district engineer Montana District office. The microscopic examinations and. the grid grain-count analyses of the samples and the beneficiation tests were made at the Bureau's laboratory at Salt Lake City, Utah, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

May 1, 1947

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947

By X. B. Starnes

"INTRODUCTION The Eva Tanguay property is in Crittenden County, Kentucky, about 1 mile south or the village of Mexico, and can be reached from Marion, the County seat, by travellng south on State Highway 91 for 6.8 miles and then turning southwest on State Highway 70 and traveling 2 miles farther.Although the property lies between the Huffaw and Pigmy properties, which together have produced 200,000 tons of fluorspar ore, production from the Eva Tanguay has been estimed at only 1,000 tons. Geological factors on the property indicated the likelihood of an ore occurrence, and the author examined the property in April 1944. Shortly thereafter, the U.S. Geological Survey wrote a report on the property, which was not published. A drilling program was initiated by the Bureau of Mines November 1, 1944, and continued until eight holes totaling 3,137.5 feet were drilled.The holes showed that the Tubb fault system on the Eva Tanguay property is composed of three members, all of which contained commercial ore. The line dividing the Haffaw and Tanguay properties crosses the vein outcrops, causing a part of the ore indicated to be on each property.The mineral rights, which are leased by Robert Frazer of Marion, are owned by Mrs. O. S. Denny and W. C. Bohn, both of Marion."

May 1, 1947

By James V. Kelly

"INTRODUCTION In the course of Bureau of Mines investigations of iron ores near Scappoose, Columbia County, Oreg. during 1942, occurrences of laterite were noted in road cuts and outcrops at many localities in the county. In 1944, the State of Oregon Department of Geology and Mineral Industries completed a preliminary examination of alumina-iron-bearing laterite occurrences in Washington County north of Hillsboro, Oreg.3/ Their report suggested that the lateritic material might be amenable to treatment by the Pederson process for the commercial production of iron and alumina. In order to determine the extent and character of some of the reported lateritic occurrences, the Bureau conducted preliminary explorations in Columbia County near St. Helens, Oreg., from January through June 1945. Almost simultaneously the Alcoa Mining Co. began to explore nearby areas. Their work was continued and expanded after the Bureau's work had been discontinued. This report presents the data obtained from the exploratory work of the Bureau of Mines.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral re¬sources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.Samples were assayed at the Reno, Nev., laboratories of the Bureau of Mines under the supervision of A. C. Rice, acting supervising engineer, and at the Albany, Oreg., laboratories under the supervision of Dr. B. A. Rogers, chief, Albany Division, Metallurgical Branch."

May 1, 1947

By Guy E. Dent, Hugo E. Kuehn

"SUMMARYFor making a comparison of magnetic surveys measured from the ground and from the air, Worcester County, Maryland, was chosen as a proving ground. Vertical magnetic intensities were observed on the ground, and total magnetic intensities were observed from the air. A comparison of the two magnetic maps reveals similar large magnetic features, but these are displaced in some instances by distances greater than a mile. Magnetic terrane in the two charts is of the same type but often differs greatly in respective characteristic features.The sacrifices in accuracy that may be expected from the use of different systems of diurnal magnetic corrections on ground observations constitute a part of this report.INTRODUCTIONThe value of magnetic surveys for gaining information concerning the crystalline basement is recognized increasingly. That this topography is often reflected to a major degree in the overlying sediments with certain offsetting is well understood. Even where such sediments are deep, the surface topography of upper formations often reflects this bedrock topography to a certain degree."

May 1, 1947

By William E. Dennis

"INTRODUCTION The San Antonio Canyon prospect was examined by engineers 3/ of the Bureau of Mines in March 1943 and again in October 1944. In July 1944, the United States Geological Survey mapped the prospect and submitted a report 4/ recommending core drilling by the Bureau of Mines. The drilling project, which was supervised by the author, was started on January 10 and completed on May 10, 1946.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. Acknowledgment is made to W. D. McMillan, engineer in charge of the Austin field office, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, for general direction and advice. The samples were analysed in the laboratory of the Metallurgical Branch at Rolla, Mo., C. Travis Anderson, chief."

May 1, 1947

By Nan C. Jensen, Oliver Bowles

"INTRODUCTION Limestone (which consists essentially of calcium carbonate) and dolomite (calcium magnesium carbonate) occur widely in the United States. Their presence is of vast economic importance, because they are used much more extensively than any other form of rock. In 1945, limestone (which, broadly, includes dolomite) was quarried in every State except Delaware, New Hampshire, North Dakota, and Rhode Island, and also in Hawaii and Puerto Rico. Total production (including that used in cement and lime manufacture) exceeded 151,700,000 tons, or 79 percent of the quantity of all kinds of stone sold or used during that year.Important well-known uses of limestone are as concrete aggregate, road material, railroad ballast, for liming the land, for cement manufacture, as riprap for shore protection, harbor work, and spillways at dams, and as building stone.. None of these uses, however, are considered herein. The purpose of this paper is to discuss the industrial and chemical uses that are less widely known and yet are of tremendous importance in a great variety of processing industries. Important examples are dolomite as a refractory furnace lining and limestone as a fluxing agent in blast furnaces, and as a raw material employed in sugar, paper, glass, and alkali manufacture.PRIOR REPORTIn May 1941, the Bureau issued a report 4/ that described these uses in some detail. As new and important developments have taken place during the ensuing years, a revision and representation of the salient features of these uses seem desirable. Asphalt filler and mineral wool uses included in the earlier report are omitted from this paper because they are identified more closely with the highway and building industries, respectively, than with the industrial applications."

May 1, 1947

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By H. L. Bibbs, H. D. Snedden

"INTRODUCTION The use of beryllium and its alloys has increased rapidly during the last decade. Further expansion of its use is limited; in part, by lack of adequately developed ore reserves. The principal commercial beryllium mineral is beryl, which is found chiefly in pegmatites and produced for market as a byproduct of the mica and feldspar industries. The coarse beryl is mined selectively, sobbed and sorted by hand, and then sold without further beneficiation. The known reserves of coarse beryl are small. No method has been available for concentrating small disseminated beryl crystals, so ores of this type have not been mined or have been left on waste dumps. Disseminated ore in low-grade unmined areas and waste dumps on developed properties is a potential source of beryl, provided a method is developed for its beneficiation.Published literature on the concentration of beryl is lacking in detail or deals chiefly with tests on artificial mixtures of pure minerals, and procedures as given were not applicable to the beryl ores tested at the Salt Lake Station. The testing procedures described in this report are independent developments. By employing these procedures, beryl was satisfactorily con¬centrated from several run-of-mine and dump ores, although these ores wore low in grade and part of the contained beryl was finely crystalline and disseminated.Beryl, quartz, and feldspar, when ground to flotation sizes, are so alike in color and general appearance that they cannot he distinguished by visual observation. The progress of the work depended on rapid determination of the grade of test products by means of the petrographic microscope. Small samples of concentrates and tailings were often cut after each addition of reagents, dried, and examined under the microscope."

May 1, 1947

By S. S. Dean, B. Silkes

"INTRODUCTION The metallurgical-research program of the Bureau of Mines .for the past 15 years has emphasized the production of high-purity nonferreus metals through the utilization of our available resources, ores, reducing agents, fuel, and power.Ore dressing or concentration, has always been a vitally important part of nonferrous metallurgy, and the Bureau continues to give most of its attention to it. In the field of the traditional nonferrous metals, the Bureau staff has developed natural-gas reduction of zinc, the application of glomerule technique to preparing high-grade lead concentrates for Scotch-hearth smelting, the production of electrolytic antimony from precious metal-bearing ores, and the recovery of nickel from nickel-chrome-iron ores.In the field of light metals, the Bureau staff has developed several improvements in both magnesium and aluminum production and in alloys of these metals. In the so-called ""rare-metal"" field, Bureau activities have included the production of pure ductile titanium on a larger scale than heretofore attempted, the electrolytic production of cobalt, chromium, and manganese which may now take their proper places as bases for nonferrous alloys as well -as ingredients of special steels. The Bureau staff has investigated many of these new alloys. Investigations of methods of recovering vanadium from its low-grade domestic ores have given promising results. Methods for the preparation of metallic zirconium have been improved."

May 1, 1947

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By W. E. Young

Iron ore occurs in abundance in Iron and Washington Counties in southwestern Utah. Outcrops are encountered over a wide area extending from Paragonah on the northeast to Bull Valley on the southwest. Outcrops also occur on the Wah Wah Range and on Blue Mountain on the north edge of Iron County. The greater concentration of known deposits occurs in and around the margins of three mountainous uplifts - Iron Mountain, Granite Mountain, and Three Peaks - comprising a belt about 3 miles wide and 23 miles long (fig. 1). This area was partly explored by the Bureau of Mines in cooperation with the Geophysical Division of the Bureau of Mines and the Geological Survey under the strategic minerals program during 1942 to 1945. The exploratory work comprised geological and topographic mapping, geophysical prospecting with a magnetometer, diamond drilling, trenching and test pitting, sampling ore exposures and old workings, and constructing and repairing roads. The Pinto-Iron Springs district is the most important known source of iron ore for the steel plants of the West. The future economic status of the Intermountain and Pacific coast regions will depend largely upon the successful development and exploitation of substantial iron-ore bodies in this district.

May 1, 1947

By Frank J.

The increased demand for aluminum for military purposes during World War II necessitated the development of domestic deposits of alumina-bearing ores. Kaolin, siliceous bauxites, anorthosite, and diaspore-containing clays have been investigated and studied in the laboratory and pilot plant. The Bureau of Mines is preparing a series of reports covering investigations of these ores. The tests contained in this report are restricted to sintering and leaching tests on kaolin from South Carolina, where extensive deposits were proved to exist. The leach liquors were found to have substantially the same composition as those produced from the diaspore-containing clays, and therefore it would be expected that no difficulty would be experienced in producing calcined alumina of relatively coarse particle size and with other properties conforming to the specifications for metallurgical-grade alumina.

May 1, 1947

By McHenry Mosier

This paper is one of a series recently undertaken by the Mining Branch of the Bureau of Mines to describe current practice in diamond drilling for production at various mines throughout the United States and to discuss the relative merits of this method compared with drilling by percussion rock drills . The Bureau of Mines and the mining companies that are cooperating with it in this ' investigation have the objective of developing information on diamond -drilling blast holes for the benefit of all who are interested in the possible improvement of mining operations .

May 1, 1947

By K. L. Kreamalmyer, A. B. Neeham

The Alice mine is one of several zinc deposits in Ozark and Howell Counties, Missouri. It was selected as the first to be investigated by the Bureau of Mines in an effort to demonstrate reserves of sulfide ore under the shallow carbonate ores from which all production of the district had come up to World War II. The property was worked first about 1890 and was most productive prior to 1900. Its output was the bulk of the district’s total up to 1940, which is believed to have been about 85,000 tons of washed and sorted ore carrying 17 to 36 percent zinc. The firm of Doane & Ives owned and operated the Alice on a scale of a few to 25 tons a day from 1940 to 1946. An open pit about 300 feet long, 250 feet wide, and 30 to 50 feet deep comprises the mine working. Numerous old drifts and shafts in the walls and bottom of the pit are now inaccessible. The ore consists of zinc and iron minerals replacing and filling openings in dolomite. Sulfides are absent or scarce to a depth of 40 to 50 feet; smithsonite was the chief ore mineral in the oxidized zone. The individual ore bodies are irregular in size, shape, and zinc content, and “horses” of waste occur within the pit. The Bureau of Mines recommended churn drilling to test the depth, extent, and richness of the zinc sulfide ore. Four holes were drilled by a private company and seven by the Bureau in and around the pit; several penetrated considerable thicknesses of material containing a few to 10 percent (metallic) zinc in the form of sphalerite.

May 1, 1947

By P. L. Russell, M. E. Volin, F. L. C. Price, D. H. Mullen

Tin deposits in Catron County, New Mexico, were explored by the Bureau of Mines under authority of the Strategic Minerals Act of August 1939. The investigation covered both lode and placer deposits and was later extended to deposits in Sierra County. Six of the known deposits were examined by E. D. Gardner, supervising engineer of the Southwest Experiment Station of the Bureau of Mines, and S. G. Lasky, a geologist of the Federal Geological Survey, in June and July 1939. It was recommended that the more promising occurrences be explored by test pitting, trenching, and sampling. Field work, under supervision of M. E. Volin, began in September and continued through December 1939. The area was mapped by Carl Fries, Jr., of the Federal Geological Survey, in 1939 and 1940. The La Cruz Development Co. acquired control of the Squaw Creek placer claims in 1942 and began active sampling and development preliminary to large-scale operations. The result of this work showed a considerably higher tin content than that found by the Bureau of Mines in 1939. Because of this report and reports from other parts of the district that large-scale operations for the production of tin from lode deposits were possible, it was recommended that the Bureau of Mines resample parts of Squaw Creek and conduct a mill test of lode material to determine whether a concentrate could be made that was high enough in tin and low enough in iron to be acceptable in American smelting practice. This work, under the supervision of Paul L. Russell, was begun in November 1942 and completed in January 1943, during which time the Sierra Metals Co. acquired control of a large area in Sawmill Canyon. At the suggestion of the Federal Geological Survey and the War Production Board, which had reason to believe that a great deal of commercial material existed on certain flatlands and gully slopes, the project was extended to include test pitting and sampling of those areas. This work was completed in February 1943.

May 1, 1947

By J. H. East

Potash is one of the essential chemicals used in fertilizing soil deficient in natural minerals . Europe uses a large tonnage of potash in the form of easily soluble salts , and this is particularly true of those countries where the natural minerals in the soil have been exhausted owing to intensive cropping of the land . The application of potash to the soil in these countries is essential if normal crops are to be obtained ; during the war , some European countries were unable to obtain sufficient potash , and productivity of the farming areas declined seriously . • The largest -known deposits of potash in the world ; with the possible. exception of Russia , occur in Germany , and the German output of processed salts constituted about 65 percent of world production prior to the war . The German potash-plant installations are large , modern , brick and steel construction and apparently built for a planned operation of many years . Two districts produced approximately 80 percent of the German potash; the Werra -Fulda district , near Vacha , had the largest production , and the Sudharz district , near Nordhausen and Sonderhausen , was second . (Fig . 1. ) Hannover and Stassfurt were two smaller producers . Potash fertilizers are rated in terms of potassium oxide (K20 ) . The usual basis for calculation of production or application of the salt is to reduce the potash content to 40 percent K₂0 .

May 1, 1947

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By John H. Soulé

"INTRODUCTION The Peerless mine was examined by W. R. Storms, an engineer of the Bureau of Mines, on June 2, 1944, in conjunction with a mineral survey of the adjoining For Bayard Military Reservation. Storms again studied the mine on January 13; 15 and 16, 1945, to determine the possibilities of finding new ore reserves to replace these depleted by mining. A project to explore the Peer-less vein at depths below and to the south of the principal mine workings was proposed. Special attention was given to the possibility of exploring favorable beds in the Magdalena and Lake Valley limestones at points near the Peerless fault.The proposed project was approve and exploratory work started on January 2, 1946, and was completed on June 5, 1946. The mine was not in operation during the project, and all equipment had been removed."

Apr 1, 1947