Search Documents

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By The Staff

Introduction It is the purpose of this paper to discuss a number of the metallurgical improvements in the technology of copper-nickel ore treatment which have been introduced during recent years in the plants of ?the International Nickel Company of Canada, Limited. In common with other ore treatment processes, the procedure for extracting nickel and copper is changing almost continuous! y. These changes are necessitated by reason of changes in ore grades and characteristics, rising material and labour charges, and the constant drive to maximize metal recovery and to minimize production costs. It is not possible to present a comprehensive list of all the changes made, and only a selected number of the improvements in the milling, smelting, and refining operations are covered. It should be clearly understood that some phases of the procedures described have been pioneered by others in kindred fields and due acknowledgment is given to their foresight and efforts. Articles have been published over the years describing the operations of the International Nickel Company plants and the reader is referred to the Engineering and Mining Journal, Vol. 130, No. 9, November 10th, 1930, and to the Canadian Mining Journal, Vol. 58, No. 11, November, 1937, and Vol. 67, No. 5, May, 1946. Other references are the Transactions of this Institute, 1932, 1938, and 1946; Metals Technology, American Institute of Mining and Metallurgical Engineers, February, 1938, and Canadian Chemistry and Process Industries, April, 1940.

Jan 1, 1948

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations, of which this is the seventh. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in , this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of .1 minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Robert N. Roby

The Hornsilver lead-zinc property was examined by the Bureau in 1942 and again in 1944. A project was started on the property in April 1946 and completed in January 1947. Silver was first discovered in this district in 1883, and while complete production records are not available, it is known that a substantial tonnage of high-grade silver ore was shipped before 1887. All of the ore was mined from surface or near-surface workings. When the high-grade oxidized ore was exhausted, the district became inactive and remained so until the 1920's. In 1928 and 1929 some activity was shown in the district, but the Hornsilver mine was not reopened until November 1937. Between 1939 and 1946, the mine produced about 16,000 tons of ore of 531 ounces of gold, 283 ounces of silver, over a million pounds of load, and nerdy 2 million pounds of zinc. The property is now controlled by the Era Mining & Development Co., which has acquired the Last Chance and Ella groups of claims, in addition to the Hornsilver mine.

Jan 1, 1948

By Edward P. Barrett

This investigation was a part of the Bureau of Mines program for the production of critical and essential materials needed for the war. The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from the low-grade iron ores of Minnesota. This investigation was conducted by the Bureau of Mines to determine the workability of the proposed shaft-furnace process and its possible use in connection with an experimental plant for the gasification of lignite operated by the Coal Division of the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1948

By Stuart Bjorklund

This paper is one of many reporting various aspects of the Bureau of Mines program initiated in August 1939 by passage of the Strategic Minerals Act J the scope of which was greatly expanded by subsequent legislation. In its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The occurrence of chromite in the Knik Valley near Palmer, Alaska, was brought to the attention of the Bureau of Mines in September 1941 by George Johnson, of Anchorage. At that time a preliminary investigation was made by Robert S. Sanford, an engineer of the Bureau of Mines. The area was investigated on June 4 and 5, 1943, by Henry R. Joesting and Leo H. Saarela, engineers of the Territorial Department of Mines. In August 1942, a second chromite occurrence, the Highway deposit, in the Knik Valley, was reported to the Territorial Department of Mines by John E. Ryan of Anchorage.

Jan 1, 1948

By Donald W. Scott

This paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the *preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizeis and organic dyes, and 35 parts of water are added to 100 parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the over-spray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1948

By James E. Bell, Clyde B. White

"INTRODUCTION The Friedensville district was one of the most important zinc-producing areas in the United States from 1859 to 1893. The ore minerals near the surface were principally calamine and smithsonite, but with depth sphalerite was found in increasing proportions. The ore bodies of the district are reported to have been in chimneys, occurring in folded and faulted beds of Beekmantown limestone of Ordovician age.The Correll was one of five mines near Friedensyille that were exten¬sively exploited. The high-grade ore shoots were mined to a depth of several hundred feet, but it is believed that inability to compete with lower-cost production elsewhere, rather than exhaustion of the ore bodies, compelled the mines to close.There is no record to indicate that any attempt was made during the period of operation to explore for additional ore in the limestone beds down the dip below the mine workings. The possibility that exploration might reveal additional ore in the limestone beds below the known ore shoots led the Bureau of Mines to diamond-drill the Correll property between September 1943 and January 1944."

Jan 1, 1948

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By William H. Baer, George M. Carlton, Blake M. Loring

IT is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen.1,2,3 Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). EXPERIMENTAL PROCEDURE The material for this investigation consisted of extruded rods 1 ¼ to 1 ½ in. in diam. The chemical compositions were as follows: [ ] The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0-015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to ±3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements.

Jan 1, 1948

By C. E. McCarthy, A. George Stern, Stanley J. Green

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By Robert S. Sanford

Intensive investigations of domestic manganese deposits were conducted by the Bureau of Mines and the Geological Survey during the earlier part of the war minerals investigations when there was doubt that the quantity of manganese needed to produce the greatly increased tonnage of steel demanded for war supplies could' to obtained from its customary sources. Domestic deposits of ores that contain sufficient manganese for direct production of ferromanganese essential in steel Manufacture are generally small, and the bulk of the supply is imported. One of the few large deposits of low-grade manganese ore known in the United States is in the Artillery Peale district in southern Mohave County, Ariz. Manganiforous sediments underlie a very large area. Several large groups of claims, covering the most of the manganese-bearing ground, wore assembled in 1929 and 1930. The greater part of this area was leased by the M. A. Hanna Co. in 1937. Investigations by engineers and geologists for this company revealed that the average content of manganese is very low; but that the Maggio Canyon area, about 180 acres, contains higher-grade material. The company put down 28 vertical diamond-drill holds to explore this ground, under the direction of B. N. Wobbor, geologist.

Jan 1, 1948

By John G. Koert, Koert D. Burnham, John G. Broughton

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.' Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation's pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3'4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

Jan 1, 1948

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948