Search Documents

By D. Harker, W. E. Seymour

CERTAIN alloys of iron and nickel, when rolled and annealed, possess a preferred crystal orientation: (001) in the rolling plane and [loo] in the rolling direction, when recrystallized at 850" to 1050°C after approximately 98 pct cold reduction. Since the preferred orientation makes a direction of easiest magnetization coincide with the rolling direction, these alloys, especially a 50 pct iron in nickel alloy, have found wide application in the electrical industry' for choke coils and special types of transformers. The rate of the recrystallization reaction was studied at temperatures ranging from 500° to 600°C. The heat of activation for the reaction was calculated from the observed rates, and crystal orientation determinations were made before and after re-crystallization. A vacuum melted iron-nickel alloy* analyzing 49.6 pct nickel, 0.018 pct carbon, and 0.30 pct manganese was used for the experiments. The alloy was cold-rolled 98 pct into strips 1/2 in. wide by 0.002 in. thick. Specimens 1 in. long were sealed under a vacuum (approximately 10-8 mm Hg) in 1/2 in. ID pyrex glass tubes. For heat treatment these tubes were fastened to Nicrohm wires and submerged in a molten salt bath controlled to ±2°C. (The maximum measurement error was within 3°C.) The time at temperature was varied logarithmically from one sample to another, and runs were made at 500°, 525", 550" and 575°C. A molten lead bath was used for a run at 600°C which was controlled to the same accuracy. To determine the extent of recrystallization after a particular time at a given temperature, a method was used suggested by the work of Decker, Asp, and Harker.3,4 This method employs an X-ray spectrometer whereby X rays are diffracted from crystallites whose diffracting atom planes are parallel to the rolling plane of the specimen. The intensities of the diffracted rays are measured by a Geiger counter. The counter can be rotated through a range of angle, and can be motor driven through this range at a speed of 2" per min. The measured intensities are plotted vs. angle by a potentiometer recorder. In a 50 pct iron-nickel alloy it was found that only (200) reflections were obtained from the rolling plane with recrystallized material, and that only (220) reflections were obtained from the rolling plane with unrecrystallized material. No other reflections were obtained under these conditions over a range of Bragg angle of 0 to 45" using either type of specimen. As a consequence, the intensity of the (200) reflections from the rolling plane was taken to indicate the amount of recrystallized ma-terial present in a specimen, and the corresponding intensity of the (220) reflections was taken to indicate the amount of unrecrystallized material present. To insure flatness and proper alignment of the reflecting specimen in the spectrometer, the sample was laid in a slot 1/2 in. wide x 0.001 in. deep which was machined in a 3/4x2x1/2 in. steel carrier. The specimen then was taped down with cellophane tape. This steel cradle was mounted vertically in the specimen holder of the spectrometer so that the bottom edge of the carrier rested against a horizontal shoulder. Intensity data used in plotting the percent of recrystallized material vs. time at temperature were obtained by directly counting the diffracted beam of nickel filtered copper Ka radiation used throughout the work. The X-ray spectrometer was employed also in obtaining pole figure data to be used for orientation determinations. At the beginning of this investigation a transmission pole figure holder was used." As a thickness of 0.002 in. of this alloy was found to be opaque to the copper Ka radiation, it was necessary to reduce the thickness of the pole figure specimen. A cold-worked sample was etched in a 50 pct HCl solution for 5 min and was found to transmit a

Jan 1, 1951

By W. A. Dickinson, H. F. Hendershot

THIS paper is a brief discussion of the past and present methods employed by the Huntington Works of The International Nickel Co., Inc., in the production of nickel and high nickel alloy seamless tubing. The various operations for both hot and cold processing will be considered in their natural sequence, together with the processing characteristics of the high nickel alloys and some descriptions of the equipment used. The tools and lubricants currently in use will be described. This discussion will relate primarily to nickel, Monel,† and Inconel,† since these are the most common of the many alloys processed into tubing at the Huntington Works. The nominal compositions of the materials are shown in Table I. CONVERSION FROM SOLID BILLETS TO TUBE SHELLS History The commercial production of seamless nickel and high nickel alloy tube shells is a comparatively recent development, the first nickel shells having been produced in 1922, Monel in 1930, and Inconel in 1931 on rotary-type piercing mills. Rolled or forged billets, ranging from 3 ½ - to 7 ½ in. diam, were pierced to produce shells ranging' in size from 4 3/8 in. OD X 0.180 in. wall to 8 3/8 in. OD X 1.0 in. wall. After piercing, the shells. were further processed by hot rolling, reeling, and sizing. Subsequent to these operations the shells were either supplied to the trade as "hot finished" tubes, or were processed by cold drawing to smaller sizes at the Huntington Works of the International Nickel Co. The extrusion of nickel and high nickel alloys also may be classed as a relative newcomer to the field of hot-forming methods, for it was not until 1928 that the commercial extrusion of these alloys was begun on a 600 long ton vertical extrusion press installed at Zenith Works of Henry Wiggin and Co., Ltd., Glasgow, Scotland. This press did considerable pioneer work and the results were so favorable that in 1937 a -2200 long ton horizontal press was installed. The quality of the inside surface of the tubing produced on this press was superior to that produced by piercing on a rotary-type mill and, as a result of this experience, a 4000 ton horizontal extrusion press was installed at the Huntington Works in 1943. Billet Preparation The first step in the extrusion, process is the selection of ingots with good hot malleability, as indicated by the test described by Martin and Bieber.1 Ingots then are forged into rough rounds which are machined to the desired billet diameter on a "bar peeler." This machine consists of a rotary head which carries the cutting tools and is driven by a 200 hp, dc motor. The feed mechanism consists of hydraulically driven input and output carriages on the respective sides of the cutter head. The diameter of the forgings used and the machined size or "billet diameter" that corresponds to the four different sizes of

Jan 1, 1951

Jan 1, 1951

THERE are two general types of scientific approach to a problem. One approach, which is the more widely known, involves an analysis of the situation at the beginning of the experiment; this is followed by an analysis of the situation at each instant of time during the experiment and leads to a-detailed description of the prevailing conditions at the end of the experiment. Suppose, for example, we wish to predict the final rest position on a billiard table of a ball moving initially in a certain known direction with a known speed. The obvious approach is to estimate or measure off its course by consideration of angles of rebound, taking account of the "English" or spin if necessary and finally estimating from experience (or calculating from coefficients of friction) the slowing down occasioned by friction, thus establishing the point of the course at which the ball may be expected to stop. Any interference with the calculated course occasioned by collision with an unanticipated object would obviously cause us to revise drastically our estimate of the rest position. This general method of approach characterized by detailed description of how one situation developed from another seems intuitively appealing and is the most widely known method. There is no doubt that it gives very satisfying results when it can be used. There is a second general method of approach. In this method, the final state of a system is predicted from knowledge of general broad principles and their application, considering only the restrictions imposed upon the system. It is unnecessary to follow the course in detail; intermediate steps are not even considered. For example, if the billiard table mentioned in the first paragraph were tilted to one corner, one could predict that the final resting place of the ball would be in that corner; this prediction can be made independent of any particular course the ball may follow. This second general method of attacking problems is the one used in thermodynamics. There its use is so outstand-

Jan 1, 1951

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.' Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By L. C. Brichta

The Melrose zinc-lead. deposit is in an area of structural disturbance of sedimentary rocks in the Melrose mining district in Cherokee County, Kans., 25 miles west of Joplin, Mo., adjacent to the northwest limits of the Tri-State district. Mining and milling in the Melrose district has been sporadic and. very limited, largely due to the high cost of exploration through great thicknesses of barren rock, 350 to 440 feet overlying the ore deposits. No mining has ever been done on the Melrose zinc-lead tract, but it has been drilled extensively. The drill-hole logy indicate extensive structural deformation, silicification, and zinc-lead deposits in the Boone limestone-chert formations of the Mississippian series, which is overlain by thick-bedded Pennsylvanian shale and sandstone. Analyses of samples from Bureau of Mines drilling indicate the ore minerals are sphalerite and galena with no evident oxidation. During the period from November 2, 1949, to March 13, 1950, the Bureau of Mines investigated the deposit by churn drilling and sampling 23 holes aggregating 10,405 feet of bore. Factual data on the investigation and logs of holes drilled by private parties and the Bureau of Mines are presented in this report.

Jan 1, 1951

By Arno C. Fieldner

From July 1, 1949, to July 1, 1950, the Bureau of Mines conducted the research and technologic work on coal and coal products that is summarized in this report. The research, described in this fifteenth of a series of resumes, is presented in more detail in publications (see footnote references) that appeared during the fiscal year, though in some cases research data are given that have not been published elsewhere. Results of research in the experimental coal mine, on explosives, and on gas and dust explosions will be found in Bureau of Mines Report of Investigations 4228, Annual Report of Research and Technologic Work on Explosives, Explosions, and Flames, Fiscal Year 1950. An over-all view of our coal, oil, end natural-gas reserves was presented, and the future possibilities for the, production of synthetic liquid fuels from coal were delineated.3/

Jan 1, 1951

By M. Leva

WITH the development of new processes for the production of synthetic liquid fuels, an extensive literature search was undertaken to uncover fundamental relationships between fluid and heat flows and the operating variables of new types of converters. Examination of published correlations revealed that considerable uncertainty existed in the correlation of the operating variables of such equipment with the pressure drops which could be expected through packed and fluidized systems; correlations proposed in the literature differed from each other frequently by as much as 75 to 100 percent. Because new processes, especially more recent modifications of the original Fischer-Tropsch process, must compete with old, firmly established processes on the basis of unit product cost, the pressure-drop correlations in the literature were considered to be too inaccurate for use in calculating the energy required to pass fluids through packed beds. The following study was begun in 1946 to develop correlations that would be suitable for the design of new equipment in which fluids are brought into contact with granular materials. To arrive at general relationships, systems were chosen that did not involve chemical reactions, and a, particular effort was made to give the correlations only in terms of quantities that are ordinarily available from general process and design specifications.

Jan 1, 1951

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

By Bernard Lewis

This report summarizes fundamental research and technical studies conducted by the Explosives and Physical Sciences Division of the Bureau of Mines from July 1, 1949, to June 30, 1950. It is the fourteenth of a series of annual reports whose aim has been to bring to the reader a résumé of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report.

Jan 1, 1951

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

By Glenn C. Reed

This report is one of a series describing investigations within the Missouri River Basin in Montana made by mining engineers of the Bureau of Mines Minerals Division, Region II. The primary purpose of these investigations is to provide information to agencies of the Department of the Interior and and others concerned with the planning of Federal power developments in the basin. The report contains such factual data as have been authorized for public distribution. The field investigations in Broadwater County were made during the late fall of 1948 and the summer of 1949. Virtually all known metallic mineral deposits and some nonmetallic mineral deposits within the county were investigated. However, some long inactive mines and prospects on which little or no information is of record may have been omitted inadvertently. Many of the mines and prospects have been inactive for extended periods. Most of the underground workings now are inaccessible. Because of such conditions, impressions gained by the inspection of surface features have been supplemented necessarily, where possible, by information obtained from Federal and State publications.

Jan 1, 1951

By McNeely DuBose

INTRODUCTORY PROSPECTING for aluminum has always been, and still is, a peculiar combination of the technical with the physical approach, and 1 want to explain my conception of the term 'prospecting' when applied to aluminum, which differs in some respects from the ordinarily accepted idea of prospecting. In the early days of gold mining, prospecting was a search in the hills and the river beds for the metal, not for its chemical combinations. And so it was in the early days of aluminum, with the difference that the search for the metal was carried on, not in the hills and dales, but in chemical laboratories. Aluminum is never found in the elemental state and at that time the metal bad never been seen, but scientists of that day bad forecast that such a metal must exist and in 1807 Sir Humphrey Davy went so far as to give this unseen metal a name, aluminum, from the Greek word alumen. This word applies to our alum, and it was from alum that Davy sought to produce the metal. It is strange to think that, in laboratories throughout England and on the continent, prospecting for aluminum was busily under way by men who had never seen the metal they were searching for. Their situation was something like that of the fisherman and the 'big one' that got away. They could describe the metal, give its exact weight, and even name it, but they could not produce visual evidence of its existence. Eventually, however, the efforts of the scientist 'prospectors' were rewarded and in 1826 the metal was actually produced, possibly first by Wohler, though Oerstedt, a Danish chemist, is usually credited with the achievement.

Jan 1, 1951

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951