Search Documents

By C. S. Barrett, D. F. Clifton

THE transformation that occurs in lithium and its solid solutions containing magnesium1,2 is similar in many respects to other diffusionless transformations of the martensitic type. This general similarity makes it desirable to investigate the transformation curves in detail. The current interest in the phenomenon of stabilization in martensitic transformations has created a need for a careful appraisal of possible stabilization effects in both cooling and heating transformations in lithium alloys. The effect of prior heat treatment on the temperature at which transformation begins and the effect of various temperature cycles in partially transformed alloys also merit attention. Limited data on some of these features were presented previously,' but the present studies have been made with improved apparatus, in which erratic fluctuations were smaller than in the earlier work, and include many independent determinations of certain critical observations. Material and Methods Geiger counter X-ray spectrometers were used: a Norelco instrument, original model, and a General Electric XRD-3. The low-temperature specimen holder has been described elsewhere." Specimens 10 mm in diam and 1.5 mm thick were held in firm contact with a copper block which was attached to the lower end of a stainless steel tube that extended up to a reservoir of liquid nitrogen. A heating coil on the tube permitted a controlled temperature gradient along the tube, so that desired temperatures and rates of heating and cooling could be obtained by controlling the heating current. The specimen was surrounded by an atmosphere of evaporated nitrogen in an insulated chamber having double cellophane windows. The temperature of the specimen was read by a thermocouple imbedded in it close to the irradiated area; the specimen could be held at constant temperature within 1°C for long periods. The body-centered cubic 200 reflection near 8 = 26" was used as the index of the amount of b.c.c. material present; occasional checks were made using the most suitable line of the low-temperature phase, the close-packed hexagonal 110 line near 8 = 29". Copper radiation was used throughout. A continuous record was made of the reflected intensities on a strip chart recorder, both when the peak intensity of a line was being followed and when the lines were being scanned at constant temperature. On the continuous recordings of peak intensity, periodic checks were made on the background intensity between the lines, and on the setting of the spectrometer for maximum intensity. The lithium-base solid solution containing 12.4 atomic pct Mg (33.3 wt pct) that had been used previously' was chosen, as it had a transformation range at relatively high temperatures, so as to permit wide temperature cycling within the range. Just prior to use a pellet was cut from the ingot,

Jan 1, 1951

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleysl and Gathmann,2 who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1951

The first difficulty encount.ered in preparing this paper was to find a definition of the word "special" as applied to steel. The first thought is "obviously any grade not mild steel" but this is an over-simplification, because the term "mild steel" covers a series of carbon ranges, each found from experience to be especially suited to the production of a particular rolled section.Even if the Australian structural mild steels are excluded it is found that no part of the plant here is independent of special steel.The face-man on Iron Monarch makes his bench safe by barring down with a 0.6% carbon steel bar. He bores a hole into the ironstone with a 0.75-0.8% carbon steel drill, driven by a jackhammer which is built of a variety of special steels. After it is shot down, the stone is lifted by an electric shovel, very few of whose steel components fall into the general category of structural grades of mild steel.Further special steels are met with in the truck into which the stone is loaded, the hauling electric locomotive, and the rails on which these .run. Even the permanent way uses more than one grade, e.g., the crossings experiencing heavy service have their frogs built with austenitic manganese steel inserts.Special steels play their part in the overhead crane which tips these trucks, and in the crushers into which they discharge, and so they can be followed right through the production line, and they are still there at the seaward end of the ship loading boom at the head of the WhyalIa ore jetty.

Jan 1, 1951

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

Jan 1, 1951

By Henry A. Stiff

The classification and correlation of water analysis data presents many problems which can be solved by graphic methocis. The pattern system, a new type of graphic procedure described in this communication, is believed to have several advantages over older methods. Examples of the application, of the pattern system to the solution of problems encountered in petroleum production are given. INTRODUCTION Several graphic methods for presenting analytical water data have been developed and are now in use.1,2,3,4 It is believed, however, that a recently developed type of graph called the "pattern" offers several advantages over other methods. This system presents a better picture of the total salt concentration than is usual in such graphs. The effect of dilution or concentration has been reduced to a minimum, and at the same time distinction between various types of water has been improved. The system is extremely versatile, yet so simple it can be plotted on ordinary graph paper and adapted to almost any type of filing system. DISCUSSION The essential feature of the pattern system is the graph shown in Fig. 1. Horizontal lines extending right and left from a vertical line at zero form the graph. Positive ions are plotted to the left while negative ions are plotted to the right. The figure immediately beneath each ion gives the scale. Most oil field waters can be plotted on a scale where 100 milli-equivalents of sodium and chloride and 10 milliequivalents of each of the other ions are represented by one scale unit. For highly concentrated brines, 1,000 milliequivalents of sodium and chloride and 100 milliequivalents of each of the

Jan 1, 1951

By M. J. Ankeny

Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the prevention of such accidents will materially improve progress in safety in the coal-mining industry. Beginning March 1950, Federal coal-mine inspectors were made responsible for completely investigating all fatal accidents in and around coal mines. During these 10 months, Federal coal-mine inspectors investigated 447 fatal accidents. This is a study of 121 of the fatal haulage accidents investigated, which constituted 27 percent of fatalities from all causes. Haulage employees represent only 12 to 15 percent of mine personnel, but, on the basis of accident frequency, their work is the most hazardous in coal mines. Fatal haulage accidents occurred in 53 bituminous coal-producing counties representing 14 States and Alaska. The physical conditions represent a cross section of' producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of modern mechanized mines.

Jan 1, 1951

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By Elliot P. Rexford

IN the early days of concrete construction, the question of quality of sand or gravel to be used as aggregate in concrete was given little or no consideration. If the construction engineer had sufficient quantity for his structure within a reasonable distance, he was contented and gave no thought to the possibility that the material might have adverse physical, chemical, or thermal properties which could cause future deterioration of his concrete and possible failure of his structure. Today a very different situation exists. With the building of larger and larger concrete structures, with a longer and longer life expectancy, the quality of the aggregate material has become of major importance. Even in small concrete structures aggregate quality cannot be passed off lightly and the quality of the aggregate must be such as to give the anticipated life without costly maintenance. The first question to arise in the selection of an aggregate is what makes a sand or gravel suitable or unsuitable for use in concrete, and how can its quality be judged. No one rock type can be depended upon to furnish sound durable material in all instances. Granitic rocks, for example, make very satisfactory aggregates in some cases, but they are among the most unsuitable of materials when they are fractured, weathered, or highly micaceous. Limestones make excellent concrete aggregates on the one hand, and on the other they may be unsound and lack durability if they contain appreciable clay, they may have a harmful chemical reaction with the cement if they contain amorphous silica, or they may have thermal characteristics which make them highly unsuitable for use in concrete. Each rock, gravel, or sand must be proved on its own merits for the particular job under consideration. The selection of suitable aggregate materials may be divided into two major phases, the geological phase which is carried on largely in the field, and the testing phase which of course is a laboratory problem; both are important. Very often the geological phase alone is sufficient for the selection of satisfactory aggregates for minor structures but for major structures both phases must be thoroughly investigated. Geological Phase In the southwest part of the country nearly every major rock type, igneous, metamorphic, and sedimentary, may be found with all imaginable intermediate phases and in all imaginable stages of alteration. Frequently very different rock types, different as to geological age, composition, and condition occur very close together. Alluvium and stream-bed sands and gravels will consist of many different rock types and even ledge rocks may vary radically as to texture and composition within the area of a quarry site. Some of the rocks make suitable aggregate materials whereas others are highly deleterious in concrete. Too often the good and the bad occur together and more than ordinary caution is required in aggregate selection. Aggregate Sources: Concrete aggregates are usually obtained from stream-bed sands and gravels or from ledge rocks. Each has certain favorable and unfavorable characteristics and it is sometimes necessary to investigate both types to determine the most suitable source for a specific structure. Stream Beds: The predominant sources of aggregate materials in southern California and Arizona are stream beds. Vast quantities of sands and gravels are brought from the mountain ranges by the rivers during times of flood but most of these streams are dry a large part of the time and hence these deposits make easily accessible sources of aggregate materials. From many standpoints stream-bed materials make very acceptable aggregates. The gravel pebbles and the sand grains are

Jan 1, 1951

By E. J. Ripling

TUBES may be produced by a large number of forming processes, the most common of which will be discussed analytically in this paper. In no case will the stress analysis for any given tube producing process be derived formally for where such analyses are available, they may be referred to readily. Rather, emphasis will be placed on the interpretation of the theory of the different processes, few of which are developed to a state that will allow rigorous mathematical analyses, in an attempt to give a rational description of the effects of the different variables involved in each method. Tube producing methods can be divided into two groups: Those used to form shells, and those used to further work these shells into a shape more suitable for their final use. Among the first group are included roll piercing, extrusion and cupping for seamless shells, and bending with welding for welded tubes. The re-forming processes include sinking, drawing with a plug, and drawing with a rod. Only the plastic forming operations will be discussed here; other forming processes such as casting shells will not be considered. PRODUCTION OF SHELLS Shells for Seamless Tubing Piercing: The extremely important process of forming an axial hole in a billet by oblique rolling never has been analyzed satisfactorily, although a certain amount of experimental work relating to this process has been conducted. There are a number of factors that make piercing difficult to analyze; one of these is the fact that piercing is not a problem in plasticity, but one in fracturing, and the laws of fracturing are even less well understood than those of plasticity. If, however, it is assumed that fracturing occurs on a surface as a result of tensile stresses acting normal to this surface, piercing can be analyzed qualitatively by examining the stresses established in the oblique rolling process. To determine the origin of the tensile stresses that are thought to effect piercing, it will be necessary to know the angular relationships between the maximum stresses that are established in piercing. These angles quite frequently can be determined in a plastic deformation process by an examination of the deformed product. For example, consider the stresses established when a tensile test is conducted on a rectangular cross-sectional specimen of pearlitic steel. When stretched, this material first flows plastically, exhibiting the well-known yield jog on a stress-strain curve. The formation of the slip areas that give rise to the yield jog can be detected during the straining, since these flowed areas cause depressions on the specimen surfaces which can be seen if the surfaces are polished highly. The plastically strained areas also can be found after the specimen has been stretched to a strain not exceeding the yield jog, by sectioning the test piece and. etching these sections with Fry's etch. With this etchant, it is possible to dis-

Jan 1, 1951

By E. S. Bumps, M. Baeyert, W. F. Craig

SOME time ago during a study of impact properties of tempered martensite,1 it was postulated that the consistently good ductility of tempered martensite might be caused by its relatively small and peculiarly shaped ferrite grains. The fer-rite grains of tempered martensite have approximately the same size and shape as the martensite "needles." Thus they form an interlocking mass of needle-shaped grains quite different from equiaxed or lamellar ferrite grain structures. When the common mechanical test methods are applied to steel, variations are often observed in the ductility of specimens that have closely similar hardness and tensile strength values. The ductility so measured appears to be structure dependent. When steel from the same heat has been heat treated to produce different structures with the same hardness, the elongation and reduction of area values from the tensile test and the transition temperature determined by the notched-bar impact test vary according to whether pearlite, tempered martensite, or other structural constituents were produced by the heat treatment. It has been widely recognized that tempered martensite gives a consistently good performance, when tempered to the same hardness as many other structures with which it has been compared. In recent years the isothermal transformation of austenite to specific structural products and the quantitative evaluation of the character of these products with respect to their nature and response to deformation has received considerable attention. The objective of the present study was to pursue somewhat further the dependence of ductility upon structure; specifically, it was desired to ascertain whether ferrite grain structure, including both shape and size of the grains, can account for the consistently good performance of tempered martensite in the notched-bar impact test. It was thought that a simple experiment would indicate whether the ferrite grain structure plays any part in the good ductility exhibited by tempered martensite in contrast to other steel structures with different types of ferrite grains. By determining the impact transition temperature, it was proposed to compare spheroidites having similar carbide particle size and spacing but obtained in such a manner that their ferrite grain structures would be very different. Spheroidite obtained by tempering martensite, with its small, needle-shaped grains, was to be compared with spheroidite from pearlite. If the latter is produced by sub-critical annealing, the ferrite grains correspond to the pearlite colonies. Thus, if the pearlite was not too coarse, the ferrite grains of spheroidite from pearlite are equiaxed in contrast to the needle-shaped grains of spheroidite from martensite. It was thought that the ferrite grain structure of spheroidite from martensite might depend to some extent upon the grain size of the prior austenite. The austenite grain boundaries limit the maximum attainable size of the martensite needles and thus of the ferrite grains in the derived spheroidite. In order to evaluate any possible influence of prior austehite grain size, spheroidites were to be prepared from martensites that had been formed from fine-grain austenite and also from coarsened austenite. As the carbide particle size and distribution were to be essentially alike in the various spheroidites, the difference would be in the ferrite grain size and shape. Thus any marked difference in transition temperature could be attributable to the character of the ferrite grain structure. There are certain considerations in assuming that these spheroidites would be equivalent in all respects except ferrite grain structure, and an attempt was made to take them into account. One of the considerations was the choice of the carbon content of the steel. An approximately eutectoid steel was selected for two reasons. First, the pearlitic structure would contain no proeutectoid ferrite which might complicate the picture by producing a non-uniform ferrite grain structure in the resulting spheroidite. Then, too, the high-carbon content would inhibit ferrite grain growth during the sub-critical treatment. Another factor to be taken into account was the choice of an alloying element to assure a martensitic structure throughout on quenching the impact specimens. Nickel was chosen, because it is a common alloying element and resides in the ferrite both upon its formation from austenite and throughout tempering. The formation of alloy carbides, or even a large solubility of the alloying element in cementite, would have complicated the interpretation by changing the composition of the ferrite .during spheroid-ization. The possibility of temper brittleness was minimized insofar as possible by using a tempering temperature as high as consistent with the 1 pct of nickel in the steel, namely, 1150°F. While it certainly is not claimed that no difference other than ferrite grain structure could exist between the spheroidites, nevertheless, reasonable precaution has been exercised within the limits of steel metallurgy. It is believed that any large difference in transition temperatures would reflect the difference in ferrite grain structure and that relatively good ductility in the spheroidites from mar-

Jan 1, 1951

By H. H. Gardner

INTRODUCTION THE problem of mechanization is one of the most vital in the minds of Alberta coal operators today. In these times of constantly increasing operating costs, any way of decreasing the cost of a ton of coal must be explored to the limit. There seems no better field for such effort than the successful application of power to the mining and loading of coal. We are fortunate in having neighbours to the south who have made .remarkable progress in recent times along these lines. Higher tonnages per man have resulted in higher wages to the employee and lower cost to the employer. It might seem that our problems could be solved merely by imitating our neighbours. Unfortunately, neither practice nor experience substantiate this conclusion. It is with the purpose of reviewing our accomplishments, as compared with practice in the United States, and at the request of the Prgoramme Committee for this meeting, that this paper is written. The Committee believes that such a general discussion and comparison may well lead to further advances in our mining methods. SUMMARY OF PRACTICE IN THE UNITED STATES A visit to the highly mechanized coal mines of the United States is always most instructive and encouraging.

Jan 1, 1951

By A. B. Irwin

Abstract The techniques used in recognizing, recording, and interpreting structures in the Slocan sedimentary ceries in the West Kootenay district of B.C. are presented here in the hope that they will be of use to others working in complexly folded areas. The general pattern of folding in the Central Slocan area is obscured by lack of outcrop over a large part of the country, lack of marker horizons, local complexities of folding, and several systems of faulting. 1t was found necessary to observe and record in great detail all primary and secondary structural features and to analyse those observations on a statistical basis. The determination of bedding tops as well as bedding attitudes proved to be of fundamental importance in determining the pattern of folding. The interpretation of secondary linear and planar structures confirm:; this pattern. Accordingly, the thickness of the Slocan sedimentary series is computed to be several times that formerly postulated. Introduction The data upon which this paper is based were collected largely during the field seasons of 1947 and 1948 when the writer was employed by the British Columbia Department of Mines on detailed mapping in the Slocan mining camp. Additional observations were made by the writer during 1950 when engaged in property examinations for the Geological Survey of Canada. This presentation is largely a condensation of part of a more comprehensive thesis (5) and is restricted to observations and conclusions pertaining to the mapping of complex folds, stripped of any hypothetical discussion. Except for some unique occurrences of primary structures, there are no features or techniques described here which are not presented in standard textbooks on structural geology. It is felt that the major contribution of this paper is the method used in applying these standard techniques to a specific field problem and in interpreting the results.

Jan 1, 1951

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1951

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson' reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."' A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By Finlayson J. F

The advantages of rapid and accurate analyses are becoming appreciated in many industries today and have resulted in a great increase in the number of samples received by their laboratories. This has caused some firms to consider the installation of one or more of the instruments available for analytical chemistry. In this country there are relatively few people with experience of instrumental methods and it is difficult for a firm considering the installation of such equipment to assess the advantages which instruments may give them, and to decide which instruments, if any, will be of most use to them. The object of this paper is to give a brief survey of instrumental methods in the field of inorganic analysis. Instrumental methods of analysis have numerous advantages when used correctly. They enable extremely rapid analyses to be made in many cases, e.g., analysis of refined lead by purely chemical means takes about two days whereas spectographically the analysis can be completed in approximately one and a half hours. The accuracy ofinstrumental methods, generally between 1 and 5%, is higher than most chemical methods for small percentages of impurities. Furthermore, if the instrument can be calibrated against absolute standards the errors are usually random and not biased to one side of the correct result. The sensitivity is high, enabling in many cases the detection and determination of smaller percentages than can be detected chemically. This high sensitivity enables and, in some cases, requires the use of very small samples, and results in considerable savings in reagents, allowing the analysis of considerably more samples without undue loss...

Jan 1, 1951

By D. E. Furman

The thermal coefficients of linear expansion for several stainless steels have been determined over the temperature range from —300° to 1000°F. The steels studied include types 301, 304, 316, 347, 310 and 330. This wide selection of compositions allows an insight into the effects of austenite stability and alloy content on the expansion characteristics. THE recent increased use of materials in low temperature applications has created a field for which the properties of austenitic iron, chromium, nickel alloys are particularly suited. Tensile and impact values of stainless steels at subzero temperatures have been made available in the technical literature but, as yet, little information has been published with respect to expansion characteristics. In order to supply this need, a study was made of several of the more common compositions. Those selected were types 301, 304, 316, 347, 310 and 330 stainless steel. Both the mean and instantaneous coefficients of linear expansion were determined over the temperature range from —300°F to 1000°F. Procedure The materials used were commercial grades with the exception of type 301 which was made in a 10# high frequency furnace. The compositions are listed in table I. All steels were given an anneal at 1950°F for 30 min and water quenched prior to machining the expansion specimens. Expansion readings were taken on specimens 0.250 in. in diam by 4.000 in. long with a fused quartz tube expansion apparatus similar to that described by Hidnert and Souder.1 Temperature measurements were made with a chromel-alurnel thermocouple calibrated for use at subzero temperatures. A bath of propane was used for temperatures from —300° to —100°F and one of alcohol from —100°F to room temperature. These baths were contained in large mouthed Dewar flasks and cooled to the desired temperature levels by passing liquid nitrogen through glass cooling coils placed in the flasks. The baths were stirred constantly for temperature equalization and were heated by immersing metal rods which were replaced frequently enough to give a heating rate of approximately 150°F per hr. A resistance wound furnace was used for heating from room temperature to 1000°F and throughout this range rates of about 450°F per hr were maintained. The furnace was designed so that the temperature gradient over the specimen was within 5°F. In most instances, the expansion readings were taken during heating from —300° to +300°F at

Jan 1, 1951

By C. G. Dunn, F. W. Daniels, M. J. Bolton

J. P. Nielsen—The data that Dr. Dunn and his associates have been obtaining are welcome checks on the theoretical aspects of grain boundary energies. With reference to the comments on the validity of the inter-facial tension concept, I should like to say that I have been having considerable difficulty myself in untangling the confusion between "interfacial tension" and "interfacial energy." The confusion however resolved itself for me when I learned that "interfacial tension" for solids, or at least crystals, is used with two distinct meanings. One meaning12. ' "hat is implied for "interfacial tension" is the work necessary to produce or increase the surface of the solid in question by a unit area, temperature and pressure held constant. This comes from the somewhat surprising but simple fact that surface tension and surface energy in the case of liquids are identical quantities. This synonymity has carried over to crystals, where it should be kept in mind that the tension connotation has meaning only by analogy with liquids and that no real stresses are being referred to. The only reason that there is apparently a set of stresses acting at a grain boundary junction is the optical illusion that liquid interfaces are being observed for the grain boundaries. The other meaning3,14,15 for the term has to do with actual states of stress in the surface of a material as would be measured by a system of forces applied to the surface to equate the surface stress state with that in the body of the crystal. J. B. Hess—Since the authors have proposed that the surface tension concept should be discarded in order to deal with the general case of interface energies in solids, their attention should be called to a recent paper by Gurney." The latter has shown, from a thermodynamic argument, that surface tension is a valid concept in solids. In fact, Gurney has rejected the idea that surface tensions are merely mathematical fiction and, instead, has given an interpretation of their physical reality. Finally, he has concluded that, as long as appreciable atomic migration takes place, specific surface energies and surface tensions must be equivalent in solids as well as in liquids. Accordingly, the authors' eqs 2 and 3 can be written with equal accuracy in terms of interface tensions, simply by replacing each E,! with its numerically and dimension-ally equivalent Interfacial tension ?,,. If the interfacial tensions (or specific energies) are independent of interfacial orientation, as is true in liquids, then the general equations that define the geometry at equilibrium of the common junction of three interfaces reduce to eq 1. However, neglect of the effect of boundary orientation is never completely justified theoretically' in dealing with crystalline solids; hence, use of eq 1 in such cases must always be considered as an approximation, though clearly a reasonable one for many purposes.1,2 At the same time, one should not be surprised that the assumption that interface tensions in solids are free from orientation

Jan 1, 1951

G. A. Moore—The tin-fusion method has been a very favorable possibility for many years. The authors apparently have settled the question that delayed the method for a long time by showing that no hydrogen is absorbed in the tin. This, of course, is very important. I want to make a few remarks concerning the absolute accuracy of analysis, which must be the final basis for deciding among the various methods. From the figures in the paper, there seems to be some re-maining slight discrepancy on the actual amount of hydrogen present in various samples which may be presumed essentially identical. (This is of the order of the precision of individual analyses but appears in averaged results.) From the analyst's viewpoint, the tally of hydrogen content can be regarded as occurring in three portions. First is a large portion which comes off easily and automatically during sample storage and later on heating in the apparatus. This is fairly easily analyzed. Second is an item which may be either positive or negative in the tally sheet. In warm or hot evolution, this is a portion which, in practice, can never be re-

Jan 1, 1951