Search Documents

By Alton B. Cook, G. B. Spencer, F. P. Bobrowski

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951

By Victor Formanek, Paul Chataignon, Maurice Rey

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By R. C. Ferguson, Harlowe Hardinge

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By V. Runolinna, R. T. Hukki

Preliminary separation of precious metals by flotation can offer a simplification of the conventional method of treatment of anode slimes. Laboratory flotation experiments show that rich gold and silver concentrate can be obtained with excellent recoveries. THE purpose of this paper is to present the results of an investigation into the possibilities of separating precious metals from anode slimes by selective flotation. The work was carried out at the State Research Institute in Helsinki, Finland. The sample of anode slimes tested was submitted by the Outo-kumpu Co. in Finland. In 1947 the average assay of filtered and dried anode slimes in the Outokumpu refinery in Pori was as follows: Au, 0.50 pct; Ag, 9.38 pct; Cu, 11.02 pct; Ni, 45.21 pct; Pb, 2.62 pct; Fe, 0.60 pct; Sn, 1.00 pct; Sb, 0.04 pct; As, 0.70 pct; Se, 4.33 pct; S, 2.32 pct; SO,, 2.17 pct; SiO2, 2.25 pct. The daily assay naturally varies considerably from the figures presented above. The present conventional method of treatment of anode slimes consists of the steps shown in the flowsheet in fig. 1. As seen from this simplified flowsheet, the present method of treatment involves many steps by which the components of the anode slimes are removed one after another until the main products, gold and silver, may be separated. Due to the small scale of operations, the above procedure is carried out in small batches requiring considerable amount of manual labor. If, however, the anode slimes could be treated in

Jan 1, 1951

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

Jan 1, 1951

Jan 1, 1951

By J. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies. THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.'-" This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications. Geology The geology of the Picher mining field is similar to that of the entire Tri-State district because the sedimentary horizons that are found here are found throughout the district, and the ore bodies in the respective horizons have similar characteristics. The beds that contain the ore bodies in the Picher field are illustrated and described in fig. 2. The five unconformities found in the mines of the Picher field are indicated on the geologic section, fig. 2. The unconformity shown at the base of Meramec (B bed) is relatively unimportant since B bed was mostly eroded from the area of the Picher field before the Chester beds were deposited. B bed has been observed in the cuttings from only a few churn drill holes. The Pennsylvanian (Cherokee shale) formation is the top horizon found in the Picher mining field. It has been eroded from the southeastern part of the field, but because of the regional dip of the sedimentary beds to the west, it attains thicknesses of 100 ft to 200 ft along the west edge of the field. It is 200 ft to 300 ft thick in the Miami trough. It was deposited on the Boone limestone surface, which contained relatively few shallow erosion channels and very few depressions. Subsequent to the deposition of the shale, solution of limestone from underlying limestone horizons by circulating solutions caused the overlying beds, including the Cherokee shale, to slump into the larger openings formed by the solution and removal of the limestone. Chert The origin of the chert in the Tri-State district has been a controversial subject among geologists. Tarr7 advocated a syngenetic origin for the chert, postulating that it formed from colloidal silica deposited in the Mississippian seas. Leith, Dake and Leighton' argued in favor of silicification of erosion

Jan 1, 1951

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20' and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines. Partly because of more limited coal reserves, the traditional German mining system is largely the longwall method, which gives an almost complete coal recovery. Backfilling must be extensively practiced to protect the longwall faces, the over and underlying seams and workings, and especially the surface industrialized areas and barge canals. The German engineers have accordingly concentrated their efforts on the design of cutters, loaders, and conveyors suitable to longwall methods rather than room and pillar methods. Undercutters with cutter bars like American models have been in use in the Ruhr since well before World War 11. In 1941 they accounted for 8.5 pct of the production. This percentage, of course, includes coal which was undercut but nevertheless had to be broken down with air hammers or with explosives. The most common of these cutters is the Eickhoff Standard cutter (see fig. 1). This machine does about 95 pct of the undercutting in the Ruhr today, and is available with either compressed air or electrical power and in at least four different sizes. A variation of the cutter is this one with two cutter bars (fig. 2). At the end of 1947 about 200 of these machines and similar cutters were accounting for 13.2 pct of the total production, a production which was, however, only 60 pct of the 1941 production rate, so that the actual cutter tonnage was only up to a small amount over 1941. In 1941 about 3 pct of the production was accounted for by shearing machines making their cut perpendicular to the longwall face. They were similar to those used in the States. These machines are today considered obsolete and now account for only 0.7 pct of the total production. They are located at only a few mines and at present do not seem to have much of a future in the Ruhr. For the future, the Ruhr miner is looking forward to rather extensive mechanization of face work, with two major types of equipment being developed almost simultaneously. On one hand there is the development of cutter loaders for use in relatively hard coal. They represent the further extension of ideas developed after relatively long experience with the Eickhoff cutter. On the other hand there has been since 1942 an intense interest in the Ruhr in the development of face-stripping methods, particularly by the Kohlenhobel (coal plow) and its modification. At the end of 1947 these cutter loaders, Kohlen-hobels and scrapers together were actually accounting for only about 1.4 pct of total production while air hammers still broke 77.1 pct and as much as 1.2 pct was actually broken by hand picks. However,

Jan 1, 1951

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By J. J. Strohl, H. J. Schwellenbach

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible. THE MacIntyre mill of the National Lead Co. has four parallel sections in which magnetic and gravity separations are made. Ore from a 5000-ton bin is fed by Hardinge constant weight feeders to a 6x12-ft open-end Marcy rod mill in each section. Rod mill discharge is bucket elevated to two 4x10-ft Tyrock screens whose oversize is returned to the rod mill. Screen undersize is pumped to Crockett separators for magnetite removal, and the Crockett tailings are sized and tabled to make an ilmenite concentrate. Minus 200-mesh material, overflowed by the Crockett and Dorrco sizers is thickened, de-slimed, and concentrated by flotation.' By 1948, the development of a successful slime flotation process and numerous improvements in the gravity circuit of the mill had increased the capacity of the available concentrating equipment. At the same time, improvements in the operating techniques of the dry crushing plant and improved feeding of the crusher by the mining department had appreciably increased the production rate per operating hour in that plant. Therefore, it was decided to take advantage of the added crusher capacity to produce a finer rod mill feed and in that way increase grinding capacity. At approximately the same time, finer screens were installed in the rod mill circuits to give finer grind and thus improve liberation of the magnetite and ilmenite from the gangue and from one another. Prior to the first part of 1948, a 3/4-in. limiting screen was used for sizing rod mill feed. The first reduction in crushing plant screen size was to 1/2 in. With this screen, the circulating load in the tertiary crushing circuit was too high and plant capacity dropped below a practical hourly rate. A 9/16-in.-sq opening screen, installed next, proved satisfac-

Jan 1, 1951

By F. M. Hamilton, H. F. Ameen

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951