Search Documents

By R. I. Jaffee, H. R. Ogden

AT the present time, there appear to be two conflicting opinions on the solubility of boron in titanium. P. Ehrlich' has indicated from X-ray diffraction work that boron is soluble in titanium up to TiB0.8 (17.8 wt pct, 44 atomic pct). The X-ray diffraction pattern for titanium was found in compositions up to TiB0.05_0.07 (1.1 to 1.6 wt pct); then, without a phase gap, superlattice lines appeared up to TiB0.8 On the other hand, Craighead, Simmons, and Eastwood' have estimated the solubility of boron in both alpha and beta titanium to be less than 0.1 wt pct, based on results of metallographic analysis. In some recent work done at Battelle, results were obtained which shed more light on the titanium-rich end of the titanium-boron system. Iodide-type titanium and high-purity crystalline boron were used in this investigation. The boron was prepared by hydrogen reduction of boron tri-bromide and deposition on a hot tungsten wire. The alloys were prepared by arc melting in an argon atmosphere of 10 cm Hg pressure on a water-cooled copper hearth. The ingots were hot rolled to strip at 850°C. Alloys containing up to 1 pct B could be hot rolled. Those containing 2 pct or more B could not be hot rolled. Metallographically, it was found that a second phase was present in alloys containing as little as 0.4 pct B, and that the quantity of second phase increased with increasing boron content. This is illustrated in Figs. la and lb, which show the microstructures of a Ti-0.4B and a Ti-1B alloy annealed in argon at 850°C. X-ray diffraction patterns of alloys containing 1 and 5 pct B revealed the presence of extra lines which correspond to the superlattice lines reported by Ehrlich.' However, no evidence was found of a shift in the lattice constants of alpha titanium indicating that there is very little, if any, solubility of boron in alpha titanium. This fact, coupled with the fact that the alloys were definitely two-phase, indicates that the extra lines are not superlattice lines, but are more probably the result of a second phase of a hexagonal structure almost identical in cell

Jan 1, 1952

By W. W. Agey

As a part of the program of investigation of domestic sources of manganese in the western United States, engineers of the Bureau of Mines examined. and obtained samples of ore from two properties in the vicinity of Barstow, San Bernardino County, Calif. In addition to these, samples from two other properties in the same vicinity were submitted by the owners. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration by ore dressing. The Big Reef manganese claims axe about 140 miles east of Barstow, Calif. The claims were leased by W., E. Thurber of San Gabriel, Calif., from the owner, C. S. VanDoren of Daggett., Calif. Manganese oxides occur as a replacement deposit in heavily brecciated andesite along a fault plane. Four samples were taken by an examining engineer of the Bureau of Mines from the ore zone, which, when composited, were representative of all the exposed ore. Preliminary tests were made on lot B, and final tests wore made on the composite sample. The Trans-Oceanic property is about 20 miles southeast of Barstow, near Newberry, in the. Pisgah mining district, Calif. The sample, submitted by the owners, was taken from a 1,000-ton reject clump from a hand-sorting operation. The ore occurs as a replacement of rhyolite.

Jan 1, 1952

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By Oliver B. Hopkins

"WE HAVE patterned our lives on the things we take from under the earth's surface. Our civilization is built upon the ore from which we obtain our metals and the fuels which power the world as we know it.Today I should like to discuss with you a newcomer to the ancient mining industry. This lusty infant of which I speak is just a century old - the oil industry.While one doesn't commonly think of oil men as delvers in the earth, It was by sinking a shaft that the first oil was obtained commercially in Canada. Men sank a shaft in a ‘gum bed' in southwestern Ontario's Lambton county, not far from Petroilia, and distilled from the gum a burning oil That was just a hundred years ago. The gum was originally liquid petroleum which had seeped to the surface and lost most of its volatile components.Later, the miners dug down to •bed-rock and soon after they were not digging but were drilling wells, as they have been ever since. From the wells they obtained erode oil.What is crude oil? It is not an element like gold, silver or lead, •but a complex mixture of compounds. These compounds are made basically from two elements, carbon and hydrogen, and are called hydrocarbons (Figure 1).The remarkable ability of these. Two elements to combine in different ways gives crude oil its physical and chemical character. The lighter hydrocarbon compounds in it are gases, at normal temperature and pressure, and these are dissolved in the other, heavier compounds."

Jan 1, 1952

By O. C. Blade

A summary of the characteristics of motor gasoline for the summer 1951 is presented in table 1, and for comparison, a similar summary for the summer 1950 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. As indicated, octane numbers of motor gasolines sold in the United states decreased approximately one-half to one octane unit from the record levels attained during the winter of 1950-51 and are a little below the octane numbers of summer 1950. However, average vapor pressures of the summer gasolines did not change, and certain distillation temperatures varied only slightly from those of the year before.

Jan 1, 1952

By Cleland N. Conwell

APPLICATION of seismic methods to the location of buried channels in placer mining is fairly common knowledge, yet some of the facets of seismic refraction surveys have remained obscure in their application to mining. This description by a member of the U. S. Bureau of Reclamation team investigating bedrock at the Oso Dam site, may offer a lead to wider application of the method for bedrock determinations in engineering of mine and mill plants, tailing disposal, and water supply. It may also offer assistance in planning geological exploration in areas covered by overburden. Pertinent, and perhaps more than passingly significant, is that the seismic survey of the Oso dam site started at noon and was completed the afternoon of the next day. Location Oso dam site is on the Navajo River, Archuleta, County, Colo., 30 miles southeast of Pagosa Springs, Colo., 10 miles northwest of Chama, N. M. Bedrock at the proposed dam site is Mesa Verde Formation, Cretaceous age sandstone. The nearest good sandstone exposure is about 5/8 of a mile upstream from the location of the seismic determinations. The material above bedrock is sand and gravel with sandy loam soil covering benches above the river. The site appeared favorable, after a geologic and topographic reconnaissance, but overburden thickness was unknown. Exploratory drilling was not contemplated in the near future so a short seismic investigation was selected as the most suitable method of determining depth to bedrock. Field Procedure Geophysically, a seismic depth investigation is simply the measurement of depth from ground surface to the top of a layer which transmits seismic waves at a higher velocity. In this case the high-velocity seismic layer tentatively correlates with the Mesa Verde sandstone. Field procedure required a seismic explorationline or "spread" with 12 geophones set at measured intervals. Explosive charges were buried at few feet in the ground and detonated at shotpoints near the ends of the spread, and at intermediate points. The time of travel of the seismic waves from the shotpoints through the ground to each of the geophones along the spread was measured and recorded photographically with equipment housed in a field truck. The seismograph on each spread provided a time-travel graph. From it were computed the speed of seismic waves in various layers below the surface and depth to each different seismic layer below the shotpoint. In the case of the Oso dam site it was possible, in addition, to determine the depths below certain geophones, because there were only two seismic layers involved. Interpretation In seismic exploration waves are refracted from the top of layers which often correspond to divisions between subsurface formations. When drill holes are available the geologic logs offer a means of correlating stratigraphic breaks with seismic layers, improving reliability of seismic interpretation in terms of depth to bedrock or other geologic terms. There were no drill holes available in the case of the work at the Oso dam site. Geologic conditions appeared favorable for seismic technique because of excellent contrast in seismic wave velocity between the overburden and the Mesa Verde formation. The upper layer had a velocity of approximately 2500 fps and was interpreted as overburden, the lower layer had a velocity of approximately 9000 fps and was assumed to be the sandstone. These velocities are of the order expected in these materials. The seismographs obtained at the Oso dam site were excellent. The energy from the shot came in strongly at each geophone, giving an easily read record. Time-travel graphs plotted from wave arrival times were uniform and made interpretation comparatively easy. In Spreads 1 and 2 near the river the lower velocity layer was 12 to 15 ft deep. For the spreads on higher ground, or the bench south of the river, it was from 15 to 29 ft deep.

Jan 1, 1952

By W. T. Turrall, D. Porter

THE crystal laboratory, Dept. of Physics, Massachusetts Institute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF2) for use in growing synthetic CaFe2 crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF2 crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO2, BaSO4, CaCO3, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, -4 mesh +10 mesh, from a feed containing over 99 pct CaF2. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1952

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant's future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant's 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952

Here, published for the first time, is the group of Anaconda officials (New York office) concerned with the planning and operations of the company's copper properties in Chile.

Jan 1, 1952

By R. V. Riley

IN the metallographic examination of the alloys of iron and silicon, several investigators1-' have reported on the occurrence of an unusual type of etched structure, particularly in the alloys of higher silicon content. This, the so-called "barley shell" structure, has been observed with iron-silicon alloys over a wide range of silicon content, and under certain circumstances it can be seen upon the micro-sections of pure iron. The barley shell structure may be demonstrated most easily with iron-silicon alloys in the range 8 to 20 pct Si after etching in a hydrofluoric acid base etchant. Two etchants which produce the structure are: Corson's reagent, which is 2 parts hydrofluoric acid, 1 part nitric acid, and 2 parts glycerol; and picric acid reagent, which is 1 part hydrofluoric acid and 1 part saturated solution of picric acid in alcohol. Both when freshly prepared and used for etching commercial silicon-iron alloys containing 14 to 16 pct Si, invariably produce the barley shell structure shown in Fig. la. It is now well known that the barley shell structure is a pseudomorph and the true structure of an alloy of this composition consists of a single phase of silico-ferrite together with graphite as shown in Fig. lb. Lower silicon alloys and even pure electrolytic iron may also be etched in the above reagents to give the barley shell provided the etchant has been either: 1—Stored in contact with glass or silica, or 2—used previously for etching an iron containing silicon. Pure iron etched in perfectly pure hydrofluoric acid base etchants free from silicon contamination gives a normal structure free from the barley shells. Therefore, although the hydrofluoric acid in the reagent primarily is responsible for the barley shells, silicon, or its compounds, also must be present, either in the etching reagent or in the specimen. It was of considerable interest to the author to read the paper by Wachtell,? in which the barley shell etch was deliberately used for the identification of the boundaries of high and low silicon areas in diffusion experiments made upon laminate bars of compacted and sintered pure iron and ferrosili-con powders. This method of utilizing the barley shell etch is novel and in the hands of the investigator gave a useful differentiation between the high and low silicon areas in those specimens. For the reasons already given, however, the technique is not to be regarded as of universal application. Misleading results might be obtained, for example, if two or more specimens were etched in the same etchant. Fresh pure reagents only must be used each time. Provided this is done and the investigators are well aware of the limitations of the method, then the barley shell pseudomorph can be made of limited use in distinguishing between higher and lower silicon areas in a microspecimen of a ferrous material. The greatest of care must be exercised in the interpretation of the results which may be regarded as qualitative only and may, in fact, not be specific to silicon alloys.

Jan 1, 1952

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By D. S. Colby

Statistics on the volume of natural gas produced in the United States were first collected for 1906. A summary of those statistics covering 1906-35 was incorporated in the 1937 Minerals Yearbook. This summary, covering 1936-50 presents, by States, a number of the more important statistics that have appeared in the natural-gas chapter of the Minerals Yearbooks. The period covered has been one of rapid expansion, especially of long-distance transmission lines. Natural gas was made available to some States for the first time; in other States the degree of dependence upon supplies transported from outside their boundaries changed rapidly. Thus, an isolated series of statistics cannot be studied without considering other regional influences that reflect in the overall operations of the industry. These tables accordingly have been designed to show for each State the simultaneous changes taking place in the various sectors surveyed. The tables show production data in the upper portion and consumption data in the lower portion. They are arranged alphabetically, by States. A copy of the 1906-35 production summary from the 1937 Minerals Yearbook has been included.

Jan 1, 1952

PRESIDENT Michael Lawrence Haider New York City PAST PRESIDENT Willis McGerald Peirce New York City VICE-PRESIDENTS 0. B. J. Fraser, New York City J. B. Morrow, Pittsburgh, Pa. J. L Gillson, Wilmington, Del. ' L F. Reinartz, Middletown, 0. Philip Kraft, New York City R. W. Thomas, Tucson, Ariz

Jan 1, 1952

The new saw mill at Cache Bay of the Geo. Gordon & Co., Ltd., a subsidiary of International Nickel Co., of Canada, is equipped with the first fully electric saw carriage drives in Ontario. It has a capacity of 120,000 ft of lumber in an 8-hr shift. About half of the mill's production is high grade white pine lumber which is shipped to the general market. The other half, red pine is used in the mining operations of International Nickel in the Sudbury district, 55 miles west of Cache Bay. [ ] Inco with a potential need of 77 million board ft a year, gets only part of its supply from the new mill. The milling firm became an Inco subsidiary Jan. 1, 1948.

Jan 1, 1952

By D. Turnbull, R. E. Cech

THE supercooling behavior of pure liquid metal droplets has been described.' The solidification behavior of small droplets of Cu-Ni alloys as a function of composition is described herein. The Cu-Ni system is of interest for such an investigation because the components are miscible in all proportions in both the liquid and solid state and the phase diagram of the system, Fig. 1, is a type often encountered in metal systems. It was noted by Van Riemsdyk2 and others that the nature of the "blick" of gold droplets during assaying is not perceptibly affected by the content of the platinum group metals that are soluble in both liquid and solid gold. With the exception of these very qualitative observations there appear to have been no prior investigations of the supercooling of alloy droplets. A series of nine alloys varying in composition by 10 pct (nominal weight) steps was made using certified OFHC copper, 99.996 pct purity, obtained from the American Brass Co., and electrolytic nickel pellets, 99.92 pct purity, obtained from the International Nickel Co. The alloys were melted and cast in vacuo in a high frequency induction furnace. Segregation was minimized by chill casting into 1-in. diam steel molds. Each alloy rod was homogenized at a temperature 50°C lower than the solidus for 100 hr in dry hydrogen. Samples for solidification experiments and chemical analysis were machined from the same portion of each rod and at a depth of in. from the rod surface. A Car-boloy tool was used in taking turnings to minimize contamination of sample by the cutting tool. As a check, a number of samples for microscopic observation were chipped from the ingot with a fragment of pyrex glass. The resultant data in all cases agreed, within experimental error, with the data obtained from machined turnings. A number of small particles, 30 to 50 micron diam, of a Cu-Ni alloy were placed in a quartz vial 1/32 in. diam x % in. long. This was inserted into a platinum ribbon heater and mounted in a high temperature microscope stage. The general procedure followed in inserting samples into the stage and measuring the temperature of melting and solidification was the same as described in an earlier paper.' A chromel-alumel thermocouple was used to study alloys of 88.93 pct Cu, 80.62 pct Cu, and 72.27 pct Cu. A platinum-10 pct rhodium thermocouple was used for the remainder of the alloys. Procedure The assembled high temperature microscope stage was first evacuated and the sample given a 2 min in situ treatment at 900 °C in dry hydrogen to remove surface oxides which might otherwise catalyze crystal nucleation. After this treatment the atmosphere was changed to purified helium and melting and solidification were observed microscopically. It was not possible to determine the solidus with certainty. However, the liquidus temperature was measured very accurately since the surface of the particle changed in appearance from coarse and uneven to smooth, mirror-like within a few degrees. The visually determined liquidus temperature was checked by finding the highest temperature to which the particle could be heated such that it did not supercool upon lowering the temperature. This temperature which checked within experimental error with that found by observing surface change was assumed to be characteristic of the thermody-namic liquidus. In order to minimize the effect of selective evaporation of copper from the alloy, samples were changed frequently and the droplets were heated no more than 50 °C in excess of the liquidus temperature T,. When the latter conditions were fulfilled, T, values were reproducible. After melting, the temperature was decreased slowly until the particles solidified. The sudden release of heat of fusion on solidification caused the

Jan 1, 1952

CONTENTS:1. Introduct'iona. Previous Accountsb. Summary of Geologyc. Physiography2. Morgan Groupa. Lithologyb. Structurec. Faulting3. The Mineral Deposita. Descriptioni. Size and Shapeii. Compositioniii. Effects of Oxidationb. Relationship to Structurec. Genesis of Ored. Mount Morgan Orebodye. Sugarloaf Orebody4. Granitea. Mount Morgan Graniteb. Town Granite'c. Moonmera Granite5. Calliungal Beds6. Razorback Beds7. Acknowledgments8. References

Jan 1, 1952

[JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington) D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I- 18th St. S. W. B'ham, Ala., Phone 56-5566]

Jan 1, 1952

By A. T. Robinson, J. E. Dorn

The electrical resistivities of aluminum alloys containing CU, Ge, Zn, Ag, Cd, and Mg were found to increase linearly with the atomic percentage of the solute atoms. Application of Linde's rule to these data suggests that each aluminum atom contributes 2.5 electrons to the metallic bond. ALTHOUGH aluminum invariably exhibits a Jt\. valence of three in ionic solids, it does not follow necessarily that its valence in the metallic state is also three. As a matter of record, many properties suggest that the number of bonding electrons in metallic aluminum is less than three. For example, as shown in Fig. 1, the atomic radii1 of the metallic elements in the solid state decrease with increasing atomic number at the beginning of any one period. The atomic radius of aluminum, however, is greater than that which would result from a regular decrease in atomic radius with increasing atomic number, suggesting that the number of bonding electrons in aluminum is somewhat less than three. Correlated with the anomalously large atomic radius of aluminum is its abnormally low melting temperature. As the atomic numbers increase in any one period, the melting temperatures of the metallic elements increase.' As shown in Fig. 2, however, the melting temperature of aluminum (13) is only slightly greater than that of magnesium (12). Again the number of bonding electrons in metallic aluminum appears to be nearer two than the expected value of three. In addition Ageev and Ageeva3 alculated the electron density distribution in the aluminum lattice. A comparison of such electron density curves for various assumed valence states of aluminum with experimentally determined curves suggests that the actual number of bonding electrons in metallic aluminum is between two and three. Hume-Rothery and Raynor', " have suggested that the above-mentioned abnormalities are associated with the overlapping of the Brillouin zones of metallic aluminum when it is in the usual face-centered cubic structure. The importance of the number of bonding electrons in metals has been extended recently into the field of mechanical properties. While formerly it was thought that the plastic properties of alpha solid solutions were primarily dependent upon the lattice strain induced in the solvent by the solute, it is now known that the difference in the number of bonding electrons of the solute and solvent also has its influence on the plastic properties."1' In order to achieve a satisfactory correlation of the effect of alloying elements on the plastic properties of aluminum alloys,"'T however, it was necessary to assume that the number of bonding electrons contributed by aluminum was about two rather than the expected value of three. It appeared to be desirable, therefore, to seek other criteria for evaluating the number of bonding electrons contributed by aluminum to its alpha solid solutions, especially in view of the practical as well as the theoretical importance of the effect of valency on the plastic properties. Norbury' was perhaps the first to illustrate that the increase in resistance of alpha solid solutions is associated with the differences in valence of the solute and solvent metals. In a series of illuminating investigations Linden-'' has shown that the electrical

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. B. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 158, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfleld Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction 1-18th St. S. W. B'ham, Ala., Phone 56-5566]

Jan 1, 1952

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation's bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952